All modelsUPDATED: A low profile case for the Raspberry Pi Large open logo with sloped edges so the pcb board is visible and an open bottom frame with LEGO feet. The pcb board can be clicked in the bottom part. The USB connector will stick out the front.Component locations are based on the Beta board. Unknown if this is the same for the production model, which depends on the dimension of the used connectors (especially the sd slot). If you would like to purchase this, please note that if it does not fit, understand that I can not and won't give a refund. Minor adjustments can be done with an exacto knife if it doesn't fit exactly. When I get a production Pi, I will adapt the design if needed.

All modelsA low profile case for the Raspberry Pi. More expensive because the full bottom and thicker walls, so extra material costs. Large logo on top with some holes for some air circulation. The USB connector will stick out the front. The case overall height is 22.4 mm.Case dimensions are based on the Beta board. Unknown if this is the same for the production model, which depends on the dimension of the used connectors (especially the sd slot). If you would like to purchase this, please note that if it does not fit, understand that I can not and won't give a refund. Minor adjustments can be done with an exacto knife if it doesn't fit exactly. When I get a production Pi, I will adapt the design if needed.

All modelsA low profile case for the Raspberry Pi To save cost the bottom is open with some corners with screwholes for fastening the case to a wall. Large logo on top with some holes for some air circulation. The USB connector will stick out the front. The case overall height is 22.4 mm. Case dimensions are based on the Beta board. Unknown if this is the same for the production model, which depends on the dimension of the used connectors (especially the sd slot). If you would like to purchase this, please note that if it does not fit, understand that I can not and won't give a refund. Minor adjustments can be done with an exacto knife if it doesn't fit exactly. When I get a production Pi, I will adapt the design if needed.

All modelsA case for the Raspberry Pi Large open frame on top so the pcb board is visible or it can be used to stack another model on top with feet which fit inside the frame. The pcb board can be clicked in the bottom part. The USB connector will stick out the front. Case dimensions are based on the Beta board. Unknown if this is the same for the production model, which depends on the dimension of the used connectors (especially the sd slot). If you would like to purchase this, please note that if it does not fit, understand that I can not and won't give a refund. Minor adjustments can be done with an exacto knife if it doesn't fit exactly. When I get a production Pi, I will adapt the design if needed.

All modelsA low profile case for the Raspberry Pi Large open logo on top so the pcb board is visible and an open bottom frame with a corner with screholes. The pcb board can be clicked in the bottom part. The USB connector will stick out the front.Case dimensions are based on the Beta board. Unknown if this is the same for the production model, which depends on the dimension of the used connectors (especially the sd slot). If you would like to purchase this, please note that if it does not fit, understand that I can not and won't give a refund. Minor adjustments can be done with an exacto knife if it doesn't fit exactly. When I get a production Pi, I will adapt the design if needed.

All modelsCase for the Raspberry Pi Large open logo on top so the pcb board is visible and an open bottom frame. The pcb board can be clicked in the bottom part. The USB connector will stick out the front.Case dimensions are based on the Beta board. Unknown if this is the same for the production model, which depends on the dimension of the used connectors (especially the sd slot). If you would like to purchase this, please note that if it does not fit, understand that I can not and won't give a refund. Minor adjustments can be done with an exacto knife if it doesn't fit exactly. When I get a production Pi, I will adapt the design if needed.

All modelsA low profile case for the Raspberry Pi Large open logo on top so the pcb board is visible and an open bottom frame. The pcb board can be clicked in the bottom part. The USB connector will stick out the front.Case dimensions are based on the Beta board. Unknown if this is the same for the production model, which depends on the dimension of the used connectors (especially the sd slot). If you would like to purchase this, please note that if it does not fit, understand that I can not and won't give a refund. Minor adjustments can be done with an exacto knife if it doesn't fit exactly. When I get a production Pi, I will adapt the design if needed.

All modelsA low profile case for the Raspberry Pi Large open logo on top so the pcb board is visible and an closed bottom with screwholes. The pcb board can be clicked in the bottom part. The USB connector will stick out the front.Case dimensions are based on the Beta board. Unknown if this is the same for the production model, which depends on the dimension of the used connectors (especially the sd slot). If you would like to purchase this, please note that if it does not fit, understand that I can not and won't give a refund. Minor adjustments can be done with an exacto knife if it doesn't fit exactly. When I get a production Pi, I will adapt the design if needed.

All modelsBottom part of a case for the Raspberry Pi with an open bottom frame. The pcb board can be clicked in the bottom part. The USB connector will stick out the front. You can combine this part with any other top part or print them in different colors.Case dimensions are based on the Beta board. Unknown if this is the same for the production model, which depends on the dimension of the used connectors (especially the sd slot). If you would like to purchase this, please note that if it does not fit, understand that I can not and won't give a refund. Minor adjustments can be done with an exacto knife if it doesn't fit exactly. When I get a production Pi, I will adapt the design if needed.

All modelsBottom part of a case for the Raspberry Pi with an open bottom frame with some small feet which will fit into a top frame, so it can be stacked. The pcb board can be clicked in the bottom part. You can combine this part with any other top part or print them in different colors.Case dimensions are based on the Beta board. Unknown if this is the same for the production model, which depends on the dimension of the used connectors (especially the sd slot). If you would like to purchase this, please note that if it does not fit, understand that I can not and won't give a refund. Minor adjustments can be done with an exacto knife if it doesn't fit exactly. When I get a production Pi, I will adapt the design if needed.

All modelsBottom part of a case for the Raspberry Pi with an open bottom frame with corners with screwholes. The pcb board can be clicked in the bottom part. The USB connector will stick out the front. You can combine this part with any other top part or print them in different colors.Case dimensions are based on the Beta board. Unknown if this is the same for the production model, which depends on the dimension of the used connectors (especially the sd slot). If you would like to purchase this, please note that if it does not fit, understand that I can not and won't give a refund. Minor adjustments can be done with an exacto knife if it doesn't fit exactly. When I get a production Pi, I will adapt the design if needed.

All modelsBottom part of a case for the Raspberry Pi with a closed bottom. The pcb board can be clicked in the bottom part. The USB connector will stick out the front. You can combine this part with any other top part or print them in different colors.Case dimensions are based on the Beta board. Unknown if this is the same for the production model, which depends on the dimension of the used connectors (especially the sd slot). If you would like to purchase this, please note that if it does not fit, understand that I can not and won't give a refund. Minor adjustments can be done with an exacto knife if it doesn't fit exactly. When I get a production Pi, I will adapt the design if needed.