Clear Ultra Fine Detail Plastic
1/700 German Leichttraktor Light Tank x10
Made by
Print With Shapeways
Choose Your Material
Choose your color and finish
Choose Your Material
$19.85
Choose your color and finish
Have a question about this product?
contact the designerYou must be logged in and verified to contact the designer.
Product Description
1/700 Scale WW2 German Army Leichttraktor Light Tank.
Contains 10 highly detailed tanks.
Contains:
Leichttraktor Light Tank
After the end of World War I, Germany was restricted in military development by the Treaty of Versailles, however a secret program under the name cover "Traktor" was developing armoured military vehicles and artillery. Its engine was mounted inside the front portion of the hull and the turret was mounted above the fighting compartment in the rear of the tank. Both Rheinmetall and Krupp produced prototypes, and in 1928, Rheinmetall was awarded the order of 289 tanks. However, some time later, the order was cancelled. Krupp models had coil spring suspensions, while Rheinmetall had leaf spring suspensions.
The Germans tested the tank in the Soviet Union under the Treaty of Rapallo – agreed between the USSR and Germany in 1922 under high secrecy and security. The testing facility used from 1926 to 1933 was named Panzertruppenschule Kama, located near Kazan in the Soviet Union. The location was a joint testing ground and tank training ground for the Red Army and Reichswehr. It was codenamed "Kama" from the words Kazan and Malbrandt because the testing grounds were near Kazan and Oberstleutenant Malbrandt was assigned to select the location for testing.
Leichter Traktor ("Light tractor") was a cover name for all three meduim tank designs produced there. In the early years of World War II it was used as a training tank.
Cleaning Information
Some part cleanup will be necessary. The 3D printing process uses a waxy substance to support certain part features during the printing process. Although the parts are cleaned by Shapeways, some waxy residue may remain. It can be safely removed with water and a mild aqueous detergent like "Simple Green" using an old, soft toothbrush, Q-tips or pipe cleaners. During the printing process, liquid resin is cured by ultraviolet light. Microscopic bits of resin may remain uncured.
Let your parts sit in direct sunlight for a few hours to fully cure the resin.
Water-based acrylic paints meant for plastics is strongly recommended. Other paints, especially enamels, may not cure on Frosted Detail 3D-printed plastics.
Use dedicated model sprue cutters to remove parts to minimise the risk of damage to parts.
Please take a look at my other items.
Painting tips and preparation
Contains 10 highly detailed tanks.
Contains:
- 10x Leichttraktor Light Tanks
Leichttraktor Light Tank
After the end of World War I, Germany was restricted in military development by the Treaty of Versailles, however a secret program under the name cover "Traktor" was developing armoured military vehicles and artillery. Its engine was mounted inside the front portion of the hull and the turret was mounted above the fighting compartment in the rear of the tank. Both Rheinmetall and Krupp produced prototypes, and in 1928, Rheinmetall was awarded the order of 289 tanks. However, some time later, the order was cancelled. Krupp models had coil spring suspensions, while Rheinmetall had leaf spring suspensions.
The Germans tested the tank in the Soviet Union under the Treaty of Rapallo – agreed between the USSR and Germany in 1922 under high secrecy and security. The testing facility used from 1926 to 1933 was named Panzertruppenschule Kama, located near Kazan in the Soviet Union. The location was a joint testing ground and tank training ground for the Red Army and Reichswehr. It was codenamed "Kama" from the words Kazan and Malbrandt because the testing grounds were near Kazan and Oberstleutenant Malbrandt was assigned to select the location for testing.
Leichter Traktor ("Light tractor") was a cover name for all three meduim tank designs produced there. In the early years of World War II it was used as a training tank.
Cleaning Information
Some part cleanup will be necessary. The 3D printing process uses a waxy substance to support certain part features during the printing process. Although the parts are cleaned by Shapeways, some waxy residue may remain. It can be safely removed with water and a mild aqueous detergent like "Simple Green" using an old, soft toothbrush, Q-tips or pipe cleaners. During the printing process, liquid resin is cured by ultraviolet light. Microscopic bits of resin may remain uncured.
Let your parts sit in direct sunlight for a few hours to fully cure the resin.
Water-based acrylic paints meant for plastics is strongly recommended. Other paints, especially enamels, may not cure on Frosted Detail 3D-printed plastics.
Use dedicated model sprue cutters to remove parts to minimise the risk of damage to parts.
Please take a look at my other items.
Painting tips and preparation
Details
What's in the box:
700 Leichttraktor X10.stl
Dimensions:
Success Rate:
First To try.
What's this?
Rating:
Mature audiences only.
