Shapeways + COVID-19  
See Solutions

Click and drag to rotate
40 Tine Knitting Garter Bar X 2 - 6.5 mm V2.stl 3d printed 6mm - 40 stitch

DIGITAL PREVIEW
Not a Photo

6mm - 40 stitch
40 Tine Knitting Garter Bar X 2 - 6.5 mm V2.stl 3d printed 6mm - 40 stitch
40 Tine Knitting Garter Bar X 2 - 6.5 mm V2.stl 3d printed 6mm - 40 stitch

DIGITAL PREVIEW
Not a Photo

40 Tine Knitting Garter Bar X 2 - 6.5 mm V2.stl 3d printed Expand with 1/4"threaded rod
40 Tine Knitting Garter Bar X 2 - 6.5 mm V2.stl 3d printed Expand with 1/4"threaded rod

DIGITAL PREVIEW
Not a Photo

40 Tine Knitting Garter Bar X 2 - 6.5 mm V2.stl 3d printed Garter Bar
40 Tine Knitting Garter Bar X 2 - 6.5 mm V2.stl 3d printed Garter Bar

DIGITAL PREVIEW
Not a Photo

40 Tine Knitting Garter Bar X 2 - 6.5 mm V2.stl 3d printed
40 Tine Knitting Garter Bar X 2 - 6.5 mm V2.stl 3d printed

DIGITAL PREVIEW
Not a Photo

40 Tine Knitting Garter Bar X 2 - 6.5 mm V2.stl

Made by
$25.66
3D printed in white nylon plastic polished to reveal a smooth matte finish.
QTY

Have a question about this product?

contact the designer
You must be logged in and verified to contact the designer.
Product Description

This is a 40 Needle / Tine 6.5mm Garter Bar: (20 needle version is available in this store) A garter bar is used on a knitting machine to remove the knitted fabric from the needles, turn it around, and replace the knitted fabric back on the needles.    The ability to do this for an entire section of fabric (not just one needle) is necessary for garter stitches, and some lace patterns and cables.  It can also be used if you have a need to temporarily remove a project from the machine.  It fits 6.5mm machines. It can be purchased in sections of either 20 or 40 needles or tines.  Purchase the number of sections as you need, depending on the number of needles in your typical project.   Any number of sections can be used.  The sections fit together and should be secured together using a piece of 1/4” threaded rod with nuts and washers on the ends.  Threaded rod is inexpensive and can be purchased at a hardware store.  The rod should be cut to the length of the assembled garter bars, with enough room to add a nut and washer at each end.  Note that this just needs to hold them together for convenience, it doesn’t need to be tight. The material default for printing this is “White Polished”. Without the “Polished”, the surface of the material is slightly rough.  If you find that your yarn still doesn’t slide easily on and off the garter bar, spray it with several coats of a glossy clear coat spray available at craft and hardware stores.  This will help smooth the surface even more.

Details
What's in the box:
40 Tine Knitting Garter Bar X 2 - 6.5 Mm V2.stl
Dimensions:
13.3 x 5.23 x 1.7 cm
Switch to inches
5.24 x 2.06 x 0.67 inches
Switch to cm
Success Rate:
First To try.
What's this?
Rating:
Mature audiences only.
Sign In or Join to comment.
 
 
Logo

Hello.

We're sorry to inform you that we no longer support this browser and can't confirm that everything will work as expected. For the best Shapeways experience, please use one of the following browsers:

Click anywhere outside this window to continue.