Tan Fine Detail Plastic
1/285 (6mm) US M8 Buford Light Tank x2
Made by
Print With Shapeways
Choose Your Material
Choose your color and finish
Choose Your Material
$18.27
Choose your color and finish
Have a question about this product?
contact the designerYou must be logged in and verified to contact the designer.
Product Description
1/285 (6mm) Scale Modern US M8 Buford Light Tank.
Contains 2 highly detailed tanks.
Contains:
M8 Buford Light Tank
The M8 Buford light tank was developed by FMC to participate in the Airborne Gun System (AGS) programme. The aim of this programme was to develop a light air-droppable tank for the airborne troops. It was intended to replace the M551A1 Sheridan. The first prototype of the XM8 was built in 1985. This tank was selected as a winner in the Armored Gun System programme and was redesignated as the M8 in 1996. Unfortunately the whole Armored Gun System programme was canceled in 1996 and the M8 Buford did not entered service with the US Army, leaving airborne forces dangerously low on firepower.
The M8 Buford uses combined aluminum and steel armor. Modular titanium add-on armor, including ERA packages can be added if necessary. The front armor with add-on packages protects the crew from 30-mm armor-piercing rounds. The M8 Buford is a relatively thin-skinned vehicle, designed to support infantry from covered position and to fight in areas where it is not going to run into main battle tanks.
Vehicle is completed with a fully-stabilized M68A1 105-mm rifled gun, or a Rheinmetall XM35 gun, fitted with an autoloader and fire control system. Fire control system is similar to that, used on the M1A2 Abrams main battle tank. Autoloader holds 19 to 21 rounds and provides a maximum rate of fire in 12 rounds per minute. Other projectiles are stowed near the driver. Gun can be loaded manually in case of emergency. During the trials it appeared that the ammunition compartment failed to contain the reaction of the ammunition, when hit by anti-tank weapons. Secondary armament consists of a coaxial 7.62-mm machine gun, and 12.7-mm MG, mounted on top of the roof. The M8 Buford has a crew of 3, including commander, gunner and driver.
Vehicle is powered by a Detroit Diesel 6V-921A turbocharged diesel engine. The M8 Buford can be airdropped from a C-130 transport aircraft or larger. The C-130 can carry one vehicle, while the C-141, C-17 and C-5 can carry two, three and five respectively. Chassis of the XM8 was also intended to serve as a platform for the LOSAT (Line-Of-Sight Anti-Tank) missile system.
A similar design was the British VFM 5 light tank, developed by Vickers. It was based on the XM8. The VFM 5 was a simplified alternative of the XM8, intended for export customers. However it received no production orders. In 2015 an updated version of the M8 was revealed by BAE Systems. This light tank is still being proposed for various customers.
Some part cleanup will be necessary. The 3D printing process uses a waxy substance to support certain part features during the printing process. Although the parts are cleaned by Shapeways, some waxy residue may remain. It can be safely removed with water and a mild aqueous detergent like "Simple Green" using an old, soft toothbrush, Q-tips or pipe cleaners. Customers report that "Bestine" and "Goo Gone" also work well.During the printing process, liquid resin is cured by ultraviolet light. Microscopic bits of resin may remain uncured.
Let your parts sit in direct sunlight for a few hours to fully cure the resin.
Water-based acrylic paints meant for plastics is strongly recommended. Other paints, especially enamels, may not cure on Frosted Detail 3D-printed plastics.
Use dedicated model sprue cutters to remove parts to minimise the risk of damage to parts.
Please take a look at my other items.
Contains 2 highly detailed tanks.
Contains:
- 2x M8 Buford Light Tanks
M8 Buford Light Tank
The M8 Buford light tank was developed by FMC to participate in the Airborne Gun System (AGS) programme. The aim of this programme was to develop a light air-droppable tank for the airborne troops. It was intended to replace the M551A1 Sheridan. The first prototype of the XM8 was built in 1985. This tank was selected as a winner in the Armored Gun System programme and was redesignated as the M8 in 1996. Unfortunately the whole Armored Gun System programme was canceled in 1996 and the M8 Buford did not entered service with the US Army, leaving airborne forces dangerously low on firepower.
The M8 Buford uses combined aluminum and steel armor. Modular titanium add-on armor, including ERA packages can be added if necessary. The front armor with add-on packages protects the crew from 30-mm armor-piercing rounds. The M8 Buford is a relatively thin-skinned vehicle, designed to support infantry from covered position and to fight in areas where it is not going to run into main battle tanks.
Vehicle is completed with a fully-stabilized M68A1 105-mm rifled gun, or a Rheinmetall XM35 gun, fitted with an autoloader and fire control system. Fire control system is similar to that, used on the M1A2 Abrams main battle tank. Autoloader holds 19 to 21 rounds and provides a maximum rate of fire in 12 rounds per minute. Other projectiles are stowed near the driver. Gun can be loaded manually in case of emergency. During the trials it appeared that the ammunition compartment failed to contain the reaction of the ammunition, when hit by anti-tank weapons. Secondary armament consists of a coaxial 7.62-mm machine gun, and 12.7-mm MG, mounted on top of the roof. The M8 Buford has a crew of 3, including commander, gunner and driver.
Vehicle is powered by a Detroit Diesel 6V-921A turbocharged diesel engine. The M8 Buford can be airdropped from a C-130 transport aircraft or larger. The C-130 can carry one vehicle, while the C-141, C-17 and C-5 can carry two, three and five respectively. Chassis of the XM8 was also intended to serve as a platform for the LOSAT (Line-Of-Sight Anti-Tank) missile system.
A similar design was the British VFM 5 light tank, developed by Vickers. It was based on the XM8. The VFM 5 was a simplified alternative of the XM8, intended for export customers. However it received no production orders. In 2015 an updated version of the M8 was revealed by BAE Systems. This light tank is still being proposed for various customers.
Some part cleanup will be necessary. The 3D printing process uses a waxy substance to support certain part features during the printing process. Although the parts are cleaned by Shapeways, some waxy residue may remain. It can be safely removed with water and a mild aqueous detergent like "Simple Green" using an old, soft toothbrush, Q-tips or pipe cleaners. Customers report that "Bestine" and "Goo Gone" also work well.During the printing process, liquid resin is cured by ultraviolet light. Microscopic bits of resin may remain uncured.
Let your parts sit in direct sunlight for a few hours to fully cure the resin.
Water-based acrylic paints meant for plastics is strongly recommended. Other paints, especially enamels, may not cure on Frosted Detail 3D-printed plastics.
Use dedicated model sprue cutters to remove parts to minimise the risk of damage to parts.
Please take a look at my other items.
Details
What's in the box:
285 M8 Buford X2.stl
Dimensions:
Success Rate:
First To try.
What's this?
Rating:
Mature audiences only.
