Tusken Slayer Elite full Chassis

This chassis is specifically for the Tusken Slayer Elite from the collaboration of SP Sabers Props and Collectables and Watto's Junkyard only.  It will not work with any other Tusken Slayer. Please make sure you have the correct hilt before ordering. 
This design is unique to the design of the hilt. Clocking the chassis using the slot in the upper hilt allows for the alignment of the upper LEDs. Set Screws within the clamp allow for locking down the upper hilt with the clamp so the upper part doesn't unscrew from the clamp.

• Holds a 22mm Speaker 
• There are slots in the chassis designed to hold  NEOPIXELS/LED STRIPS 3.5MM WIDTH WS2812 2020 MINI FLEXIBLE ACCENT LED STRIP. For example:

https://thesaberarmory.com/collections/neopixels-led-strips/products/3-5mm-width-ws2812-2020-mini-flexible-led-strip-neopixel-rgb-accent-5050-led

• There are two led holders just above the battery slot that is meant to hold 5mm diameter LEDs such as these

 https://thesaberarmory.com/collections/neopixels-led-strips/products/nano-neopixel-rgb-accent-led-chainable-5mm-outer-diameter

• The switches used in this build are 4.5mmx4.5mmx3.8mm tactile switches for example: 

Saber Merchant on Etsy
https://www.etsy.com/listing/820479856/tactile-momentary-switches?click_key=751384da8ab5e58392904626ba332f51b88fc7e6%3A820479856&click_sum=038a93fd&ref=search_recently_viewed-1&sts=1

• four 1/8x1/16 inch earth magnets will also be required. One glues to each button and one glue to each plunger. Be sure to get the polarity right.  Follow the link for example:

https://www.ebay.com/itm/274323140628?hash=item3fdeeef014:g:Oy4AAOSwoP1egOww&amdata=enc%3AAQAHAAAA4CnSYMpBTibJtcS4h%2FIHjoQkjDJ%2BG8Yn%2B2V%2B%2BJYU2vEJ0ToFAtG2n49BLddkobm0vMX7i3MTkWpKtf1wgv%2BZhPFIBtQlfBbP6JyI5O7PsSzGQYajrfw7IRs5XmRLOR%2BUnihejhFKxot6qxus4cYjeXRKadHwlr%2BgH3oW%2BH4t7SaupAdldw5g1B0G81knZMlDdThWiastf%2BXmPL3ctx7oGmy3N10qYvD1Sc4GPhWhyacBKdkyzK2HBFq%2FfjKXb3xaVnCbPrkufmN8mkGU%2Fiwx2MdRu4ihX5jOCqfEx1wl%2BenP%7Ctkp%3ABk9SR5D1kKKOYQ

• The neopixel pcb holder at the top of the chassis is desiged to hold a ShtokCustomworx V3 long pin with the Cover. See Link for example. 

https://thesaberarmory.com/collections/shtokcustomworx/products/shtokcustomworx-npxl-v3-pcb-lens-cover

As installers, we always know going in that there may be necessary work that will be required of you when dealing with printed chassis and parts. Some sanding here and there, or trimming of certain places. We try to design everything with the intent that it will work without having to do any of these things, but just note that some elbow grease may be required. Final note, on the video below skip to the 3 minute mark to go directly to the chassis.