Atom Sabers Kanan Jedi Temple Mk2 Chassis Proffie
Made by
Print With Shapeways
Choose Your Material
Choose your color and finish
Choose Your Material
$67.31
Choose your color and finish
Have a question about this product?
contact the designerYou must be logged in and verified to contact the designer.
Product Description
Chassis for the AtomSabers Kanan Jedi Temple hilts with the side button only variant.
This can not be used for this hilt if you bough the AV switch option.
This is a removable battery design. The battery tabs required are the type shown in the link below:
https://www.ebay.co.uk/itm/20Pairs-18650-Battery-Negative-to-Positive-Conversion-Spring-Contact-16-5mmx16mm/362591431441?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2057872.m2749.l2649
For this chassis you will also require two of the Mk2 Paddles, but all other printed items are included in this print. You will need to carefully snip off the stems shown highlighted in red. This design allows for accent strips to be retained so the clear Mk2 paddles can be illuminated. You can see this in action on my insta page;
https://www.instagram.com/p/CbLloqbKhhY/
https://www.instagram.com/p/CbOBirgqn6e/
This chassis is designed for use with:
-Proffie Board
-KR Sabers 28mm Bass speaker
-18650 Lithium Ion Battery
-Shtok Short Pin Hilt side LED PCB (most likely requires sanding down on the outside diameter)
-KR Blade Magnet
-128x32 OLED screen
-Shtok FSC-BT909 Bluetooth PCB unit
-High Amp kill switch
-Shtok speaker PCB set
-Two accent strips, 8 pixel long
-Two 4x4x1.5mm SMD micro tactile switches
If you are struggling to get the battery tabs in to the chassis, I recommend heating them up with a clean soldering iron as you insert them. It also helps the plastic form around the tabs to grab them even more.
The chassis is designed to be fully removable from the hilt.
I did have to file a smidge off the 28mm speaker to get it to slide between the switch pads, down the hilt.
Handle with care.
Any damage occurred during installation is the responsibility of the individual installer.
This can not be used for this hilt if you bough the AV switch option.
This is a removable battery design. The battery tabs required are the type shown in the link below:
https://www.ebay.co.uk/itm/20Pairs-18650-Battery-Negative-to-Positive-Conversion-Spring-Contact-16-5mmx16mm/362591431441?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2057872.m2749.l2649
For this chassis you will also require two of the Mk2 Paddles, but all other printed items are included in this print. You will need to carefully snip off the stems shown highlighted in red. This design allows for accent strips to be retained so the clear Mk2 paddles can be illuminated. You can see this in action on my insta page;
https://www.instagram.com/p/CbLloqbKhhY/
https://www.instagram.com/p/CbOBirgqn6e/
This chassis is designed for use with:
-Proffie Board
-KR Sabers 28mm Bass speaker
-18650 Lithium Ion Battery
-Shtok Short Pin Hilt side LED PCB (most likely requires sanding down on the outside diameter)
-KR Blade Magnet
-128x32 OLED screen
-Shtok FSC-BT909 Bluetooth PCB unit
-High Amp kill switch
-Shtok speaker PCB set
-Two accent strips, 8 pixel long
-Two 4x4x1.5mm SMD micro tactile switches
If you are struggling to get the battery tabs in to the chassis, I recommend heating them up with a clean soldering iron as you insert them. It also helps the plastic form around the tabs to grab them even more.
The chassis is designed to be fully removable from the hilt.
I did have to file a smidge off the 28mm speaker to get it to slide between the switch pads, down the hilt.
Handle with care.
Any damage occurred during installation is the responsibility of the individual installer.
Details
What's in the box:
Jimmy's Saber Junk Atom Sabers Kanan Jedi Temple M
Dimensions:
Success Rate:
First To try.
What's this?
Rating:
Mature audiences only.
