White Natural Versatile Plastic
Windu Elite BatteryHolder - (Part 6/8)
Made by
Print With Shapeways
Choose Your Material
Choose your color and finish
Choose Your Material
$20.90
Choose your color and finish
Have a question about this product?
contact the designerYou must be logged in and verified to contact the designer.
Product Description
Elite-Chassis for 89sabers Windu
Holds a prewired 18500 Li Ion battery (protected). Lock down with chassis cap.
The crystal chamber has a dedicated channel to lead the wires to the board and RCP location.
Switch- and LED-wires can be placed in the remaining space. Feed them right into the flat wire channel of the chamber.
There are 2 locations for 2 neodym magnets (round 4x1mm) to be glued in there. Be sure about the polarity of the magnets of the front crystalholder where the other 2 magnets are glued in.
Hilt mounting: Drill a hole and tap a thread (m3 or similar inch) 15mm behind the switchholder cutout. Make sure you place the hole centered behind the middle button. A 3mm long setscrew holds the batteryholder in place. Don't drive in too deep in order not to damage wires or battery. You may need to cut your setscrew a little shorter.
Features:
-Plecter Labs Prizm V5.1
-18500 LI-Ion Battery
-2x 3mm accent LED
-crystal chamber
-1x 5mm crystal LED (rgb for violet)
-24mm bass speaker
-28awg wire required (0.09mm² cross section) / 0.25mm² cross section for battery and LED positive
-quick connector RICE port (2.54mm grid)
-2.1mm rechargeport
-snappers for 2W resistors (5mm OD)
Full assembly requires follwing parts to be purchased seperately by yourself:
-4x neodym magnets (round 4x1mm)
-set screws m3 thread or similar inch thread (2x 6mm long, 7x 4mm long, 2x 3mm long for chassis and heatsink retention)
-2.54mm grid connector (3 pins) for RICE
Holds a prewired 18500 Li Ion battery (protected). Lock down with chassis cap.
The crystal chamber has a dedicated channel to lead the wires to the board and RCP location.
Switch- and LED-wires can be placed in the remaining space. Feed them right into the flat wire channel of the chamber.
There are 2 locations for 2 neodym magnets (round 4x1mm) to be glued in there. Be sure about the polarity of the magnets of the front crystalholder where the other 2 magnets are glued in.
Hilt mounting: Drill a hole and tap a thread (m3 or similar inch) 15mm behind the switchholder cutout. Make sure you place the hole centered behind the middle button. A 3mm long setscrew holds the batteryholder in place. Don't drive in too deep in order not to damage wires or battery. You may need to cut your setscrew a little shorter.
Features:
-Plecter Labs Prizm V5.1
-18500 LI-Ion Battery
-2x 3mm accent LED
-crystal chamber
-1x 5mm crystal LED (rgb for violet)
-24mm bass speaker
-28awg wire required (0.09mm² cross section) / 0.25mm² cross section for battery and LED positive
-quick connector RICE port (2.54mm grid)
-2.1mm rechargeport
-snappers for 2W resistors (5mm OD)
Full assembly requires follwing parts to be purchased seperately by yourself:
-4x neodym magnets (round 4x1mm)
-set screws m3 thread or similar inch thread (2x 6mm long, 7x 4mm long, 2x 3mm long for chassis and heatsink retention)
-2.54mm grid connector (3 pins) for RICE
Details
What's in the box:
WinduEliteBatteryHolder
Dimensions:
Success Rate:
First To try.
What's this?
Rating:
Mature audiences only.
