White Natural Versatile Plastic
89Sabers Korbanth Depa V1 Proffie Chassis P1
Made by
Print With Shapeways
Choose Your Material
Choose your color and finish
Choose Your Material
$39.28
Choose your color and finish
Have a question about this product?
contact the designerYou must be logged in and verified to contact the designer.
Product Description
Chassis for the 89 Sabers Korbanth Depa hilts.
For this chassis you will also require the P2 & P3 of the design.
This is a removable battery design. The battery tabs required are the type shown in the link below:
https://www.ebay.co.uk/itm/20Pairs-18650-Battery-Negative-to-Positive-Conversion-Spring-Contact-16-5mmx16mm/362591431441?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2057872.m2749.l2649
This chassis is designed for use with:
-Proffie Board
-KR Sabers 28mm Bass speaker
-18650 Lithium Ion Battery
-High Amp kill switch
- ShtokCustomWorx Rotary NeoPixel & 2 Button PCB Connector Set (most likely requires sanding down on the outside diameter)
-Shtok Short Pin Hilt side LED PCB (most likely requires sanding down on the outside diameter)
-6 x 6 x 4.3mm tactile switch
This design allows for the board to slide into place once wired up and tested.
The kill switch requires gluing in to place once everything is wired up and tested. We recommend a dab of hot glue to secure it.
If you struggle inserting the battery tabs, I suggest carefully warming the tabs with a clean soldering iron as inserting them. It will help for the plastic surrounding the tabs to grip them.
The fixed half on the chassis is designed to be self retaining via threading the emitter to the switch house. Once you have wired up the switch house P2 fully, insert P2 into the hilt, orientate the switch, thread on the emitter P3, wire on the shtok NPXL connector and carefully cramfu the wires down until your shtok PCB fits into the emitter.
Handle with care.
Any damage occurred during installation is the responsibility of the individual installer.
For this chassis you will also require the P2 & P3 of the design.
This is a removable battery design. The battery tabs required are the type shown in the link below:
https://www.ebay.co.uk/itm/20Pairs-18650-Battery-Negative-to-Positive-Conversion-Spring-Contact-16-5mmx16mm/362591431441?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2057872.m2749.l2649
This chassis is designed for use with:
-Proffie Board
-KR Sabers 28mm Bass speaker
-18650 Lithium Ion Battery
-High Amp kill switch
- ShtokCustomWorx Rotary NeoPixel & 2 Button PCB Connector Set (most likely requires sanding down on the outside diameter)
-Shtok Short Pin Hilt side LED PCB (most likely requires sanding down on the outside diameter)
-6 x 6 x 4.3mm tactile switch
This design allows for the board to slide into place once wired up and tested.
The kill switch requires gluing in to place once everything is wired up and tested. We recommend a dab of hot glue to secure it.
If you struggle inserting the battery tabs, I suggest carefully warming the tabs with a clean soldering iron as inserting them. It will help for the plastic surrounding the tabs to grip them.
The fixed half on the chassis is designed to be self retaining via threading the emitter to the switch house. Once you have wired up the switch house P2 fully, insert P2 into the hilt, orientate the switch, thread on the emitter P3, wire on the shtok NPXL connector and carefully cramfu the wires down until your shtok PCB fits into the emitter.
Handle with care.
Any damage occurred during installation is the responsibility of the individual installer.
Details
What's in the box:
Jimmy's Lightsaber Junk 89Sabers Korbanth Depa Pro
Dimensions:
Success Rate:
First To try.
What's this?
Rating:
Mature audiences only.
