White Natural Versatile Plastic
OR SSMp Chassis Battery/Speaker holder P1
Made by
Print With Shapeways
Choose Your Material
Choose your color and finish
Choose Your Material
$29.10
Basic Materials Best Value
Shop Owner Recommendations
Choose your color and finish
Have a question about this product?
contact the designerYou must be logged in and verified to contact the designer.
Product Description
Chassis for the One Replicas SSMp Darth Vader hilts.
You will need to purchase the P2 part of the chassis to complete your install.
This is a removable chassis design that allows this P1 battery speaker chassis to be removed from the hilt with ease while the P2 part of the chassis stays fixed.
This is a removable battery design. The battery tabs required are the type shown in the link below:
https://www.ebay.co.uk/itm/20Pairs-18650-Battery-Negative-to-Positive-Conversion-Spring-Contact-16-5mmx16mm/362591431441?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2057872.m2749.l2649
This chassis is designed for use with:
-Proffie Board V2, GHV3 or Verso (depending which P2 listing you purchase)
-KR Sabers 22mm Bass speaker
-18650 Lithium Ion Battery
-Shtok Short Pin Hilt side LED PCB (most likely requires sanding down on the outside diameter) or in hilt LED (using the heatsink included with the hilt - depending which P2 listing you purchase)
- ShtokCustomWorx Battery and Speaker PCB Connector Set
- High Amp Kill Switch
One chassis per purchase. This design allows for the board to slide into place once wired up and tested.
This chassis allows for one of the included switch that came with the hilt to be used on the rear button if desired.
After wires are soldered to the battery tabs, I suggest carefully heating up the battery tabs to insert them in to the chassis. This not only makes it alot easier to insert them, but also forms the plastic around them, holding them far better.
Handle with care.
Any damage occurred during installation is the responsibility of the individual installer.
You will need to purchase the P2 part of the chassis to complete your install.
This is a removable chassis design that allows this P1 battery speaker chassis to be removed from the hilt with ease while the P2 part of the chassis stays fixed.
This is a removable battery design. The battery tabs required are the type shown in the link below:
https://www.ebay.co.uk/itm/20Pairs-18650-Battery-Negative-to-Positive-Conversion-Spring-Contact-16-5mmx16mm/362591431441?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2057872.m2749.l2649
This chassis is designed for use with:
-Proffie Board V2, GHV3 or Verso (depending which P2 listing you purchase)
-KR Sabers 22mm Bass speaker
-18650 Lithium Ion Battery
-Shtok Short Pin Hilt side LED PCB (most likely requires sanding down on the outside diameter) or in hilt LED (using the heatsink included with the hilt - depending which P2 listing you purchase)
- ShtokCustomWorx Battery and Speaker PCB Connector Set
- High Amp Kill Switch
One chassis per purchase. This design allows for the board to slide into place once wired up and tested.
This chassis allows for one of the included switch that came with the hilt to be used on the rear button if desired.
After wires are soldered to the battery tabs, I suggest carefully heating up the battery tabs to insert them in to the chassis. This not only makes it alot easier to insert them, but also forms the plastic around them, holding them far better.
Handle with care.
Any damage occurred during installation is the responsibility of the individual installer.
Details
What's in the box:
OR SSMp Battery P1
Dimensions:
Success Rate:
First To try.
What's this?
Rating:
Mature audiences only.
