fusionimaging@Lidja That should work but because of the tapering of the rubber ends it might get in the way of the top of the visor by pushing down on it. Unfortunately we cannot except returns as every product is made to order.
fusionimaging@Lidja It really depends on the design of the Ram mount. Our visor has been designed to be clamped on the top and bottom for use with a DJI remote, so if your RAM mount attaches in the same way then you should have no issues.
fusionimaging@spinalator With the amount of various cases around it would be very difficult to make a product that fit everything so all our visors are made to be used with phones only, not with cases. Thanks for your message and interest in our products.
fusionimaging@michael_boykin Hi thanks for your enquiry. The hood has been designed specifically for the Galaxy Note 4. We have not tested it on the Note 5 so cannot confirm if it would fit as the dimensions or hole placement might not be the same. Thanks for your interest in our products.
fusionimaging@RocketBrew Hi thanks for your message. We have decided to take this product off sale until we further investigate this issue further. We appreciate your concern and will look further into what is the issue and how we can resolve it. Thanks for your support.
fusionimaging The flytrex mount was designed in collaboration with Flytrex and to their specifications. The design was totally guided by the instructions given to us. We apologise for your experience, its certainly not the experience we want our customers to have. Thank you for letting us know.
fusionimaging@rickhartmanii Thanks for your comment. Our disclaimer is on every product we sell. The Gimbal Guard fits like a glove and to date we have had no issues from any of our customers with the way it fits.
fusionimaging@greg2 It was designed for that very purpose of easy attachment and removal. It literally just snaps on, and snaps off using the same design philosophy as our prop guard connectors. It literally takes you a second to put on and take off. Thanks for your interest.
fusionimaging The cap is quite long as you can see from the photos so there is room inside depending on how deep you slide it on. There is however no additional clearance on the side so if your filter is wider than the side of the lens shaft it wont fit.
fusionimaging@Arlockway2_ Please see attached image, we found that these 4 screws are the only ones holding the U bracket in place on the phantom leg. Once loosened the unit is free to move up or done. Hope this helps. Otherwise let us know. Cheers.
fusionimaging@Arlockway2_ Hi thanks for your message. We dont quite understand what you mean, could you please explain ?. We do sell 2 versions of the Leg Extenders, the standard version and an update to our original series of leg extenders designed to incorporate the new late 2014 update to the DJI Phantom that has the Compass (anti-static) rear leg.
fusionimaging Yea there's quite a few attempts out there with coke bottles. The competition is more about exploring the possibilities of 3D printing and generating interest in this new frontier of crowd sourced manufacturing path. We covered all bases for something more practical and contributed quite a few more to the competition. Some of them already made it out of beta =)
fusionimaging@noctividus We've so far spent about $400 of the winning to prototype lower priced phantom 3 accessories and more to come.
We would like to throw $1000 for a marketing stunt, but at the moment we'd believe it's better off spent on R&D of sub $100 products.
fusionimaging@noctividus Thanks for the feedback, you're quite right.
The competition is more about exploring the possibilities of 3D printing and generating interest in this new frontier of crowd sourced manufacturing path.
While we haven't considered selling this product outside of its 'beta' monikor and have slapped on a bold warning as per your recommendation, for the competition we've worked hard to provide with many products that are less insane and more decent priced. Many of them are available for sale already.
Hope that helps clearning any confusion about the competition and thanks for the comment!
fusionimaging Yea I think there's also another guy who designed one. It's surely interesting. This one's approx 500mm long each floater, space wide apart to minimise chance of rolling over in the water.
fusionimaging@seafood10 Hi, current shipping times suggest leaving the factory around July 24-27. Lately all our orders have taken about a week to make and a week to ship to Australia. So anywhere else could be quicker but its an approx time. They are shipped direct from the factory to our customers around the world, so times can vary. When you order you will get an approx ship date so just add shipping time to that.
fusionimaging@dbehr Hi, thanks for your enquiry. Unfortunately we only make mounts for the iPad Mini, and iPad Air models. We do however make visors/fpv hoods for certain Samsung Galaxy models. Thanks for your interest in our products.
fusionimaging@Johntom Hi, unfortunately we do not have access to that information, you will need to contact shapeways at firstname.lastname@example.org. When you made your order you should have been given an estimated ship date so check the order status on your 'orders' page which might also be able to assist you. Team Fusion.
fusionimaging@TiagoMatias Hi, yes our product are just the connectors. You have to purchase the prop guard separately. We recommend 4x M3 13mm or longer screws with nuts to screw the prop guards to the connectors, or you can just use the screws that came with the prop guards, although you will need to also purchase nuts for them. Hope that helps.
fusionimaging@TiagoMatias that product works on all Phantom models because the body is the same. We have tested it on all models including the new Phantom 3 and it works perfectly. A very tight secure fit with the new version 4.
fusionimaging@mbrassette From what we understand there is no issue with the design and the issues shapeways were experiencing with some products being brittle due manufacturing issues, has been rectified.