Spacer1999 Metah Probe

Spacer1999 Metah Probe 3d printed SciFi Vehicles Scouls502 says: I think this is a super model of the 'Probe'
Scouls502 says: I think this is a super model of the 'Probe'
Spacer1999 Metah Probe 3d printed SciFi Vehicles
Spacer1999 Metah Probe 3d printed SciFi Vehicles
Spacer1999 Metah Probe 3d printed SciFi Vehicles Scouls502 says: Another outstanding model in detail plastic. Excellent!
Spacer1999 Metah Probe 3d printed SciFi Vehicles Scouls502 says: Another outstanding model in detail plastic. Excellent!
Scouls502 says: Another outstanding model in detail plastic. Excellent!
3d Model Viewer
Spacer1999 Metah Probe 3d printed SciFi Vehicles
Spacer1999 Metah Probe 3d printed SciFi Vehicles
Spacer1999 Metah Probe 3d printed SciFi Vehicles Scouls502 says: I think this is a super model of the 'Probe'
Spacer1999 Metah Probe 3d printed SciFi Vehicles Scouls502 says: I think this is a super model of the 'Probe'
Scouls502 says: I think this is a super model of the 'Probe'
This is the Spacer1999 Meta Probe ship. It's correct as can be for this scale. It uses the same head as on the 31mm Eagles. So it is 1/1000 scale. This version has had extra support bars added on to the solar panels. This is for printing purposes only. Once you get it, just cut the 2 end bars out, leaving only the center bar as the main bar holding the solar panels in place. The test print is done. It appears to have no further issues. Markup has been dropped for this model for the holidays. Enjoy.

Want to get a set?

+ + +




cm: 2.242 w x 6.4 d x 0.588 h
in: 0.883 w x 2.52 d x 0.231 h

Comments

 
very nice
December 1, 2013, 8:22 am
@Mechanoid "You could have removed the 2 end support bars for the solar panels. They only had to be there so ShapeWays would print it without rejection." I did consider that but decided to leave them in place for extra strength. I have another which I will snip these off but for the first one I decided to just leave as is. Can't wait to see what else you come up with.
November 24, 2013, 2:51 pm
@Scouls502 Well now you went and done it. Made the model look all nice and stuff. LOL Only one thing to do, make it "THEE" primary image for this model. There, take that. LOL You could have removed the 2 end support bars for the solar panels. They only had to be there so ShapeWays would print it without rejection. I used nail clippers to remove the end bars from my test print model.
November 24, 2013, 1:18 pm
I think this is a super model of the 'Probe'
November 24, 2013, 11:01 am
@Mechanoid No problem and if it helps lead to more sales then by default that should lead to more models. A win win for everyone.
November 17, 2013, 12:59 pm
@Scouls502 And once again I must thank you for sharing another fantastic pic of this model. It is now the primary for this model. I hope you don't mind all this attention. But Thank You.
November 17, 2013, 4:25 am
Another outstanding model in detail plastic. Excellent!
November 16, 2013, 12:03 pm
 
  • White Strong & Flexible

    White nylon plastic with a matte finish and slight grainy feel.

    $4.28

Favorited by