by
TheoJansen
The third public evolution of the Animaris Geneticus Parvus. #7 has evolved legs, with pointy feet instead of flat. Featuring a fully working Theo Jansen mechanism as used in his work "the Rhinoceros".
Also see our new Propeller Propulsion add-on, to have your Strandbeest walk autonomously!
The mechanism is printed assembled, and will work without further assembly right after birth from the printer.
A few tips to consider:
- After birth there might be a little powder left in some joints, or it might not go supersmooth. This will fix itself after the animal has a little bit of practice!
- Some surfaces work better than others. The legs require a little friction, and a flat surface. So for example: A rough table or floor, thin flat carpeting, or a thin rubber sheet. It will slip on a too smooth surface.
- The best way to push it is by its nameplate. Do not push down, but forward.
- The beest is light, but quite strong. It can actually be dropped without breaking. It is not a "toy" however, and not suitable for children. The 3D printer material is easy to stain so clean hands are advised.
Also see our new Propeller Propulsion add-on, to have your Strandbeest walk autonomously!
The mechanism is printed assembled, and will work without further assembly right after birth from the printer.
A few tips to consider:
- After birth there might be a little powder left in some joints, or it might not go supersmooth. This will fix itself after the animal has a little bit of practice!
- Some surfaces work better than others. The legs require a little friction, and a flat surface. So for example: A rough table or floor, thin flat carpeting, or a thin rubber sheet. It will slip on a too smooth surface.
- The best way to push it is by its nameplate. Do not push down, but forward.
- The beest is light, but quite strong. It can actually be dropped without breaking. It is not a "toy" however, and not suitable for children. The 3D printer material is easy to stain so clean hands are advised.
by
COVO
Product Name "Cat Skull Ring". Designed by Japan.
Want to know more puroduct detail? Watch movie.
The material of movie is Silver Glossy.
Available in either stainless steel (antique bronze & gold plated) or silver.
The default size is 20.6 mm inner diameter but you can customize the size to your liking.
Click personalize to choose your US ring size.(Size support: # 8 to # 11.)
Please refer to a this page.
Conversion chart for ring sizes
US Ring Size Inside diameter
8 18.1mm
9 19.0mm
10 19.8mm
11 20.6mm
Please also see other designs.
Shop here.
http://www.shapeways.com/shops/forma
Want to know more puroduct detail? Watch movie.
The material of movie is Silver Glossy.
Available in either stainless steel (antique bronze & gold plated) or silver.
The default size is 20.6 mm inner diameter but you can customize the size to your liking.
Click personalize to choose your US ring size.(Size support: # 8 to # 11.)
Please refer to a this page.
Conversion chart for ring sizes
US Ring Size Inside diameter
8 18.1mm
9 19.0mm
10 19.8mm
11 20.6mm
Please also see other designs.
Shop here.
http://www.shapeways.com/shops/forma
by
SheilaMunro
Beautifully detailed 2.2 inch-long Raven Pendant. looks amazing in silver! :) The picture above is an actual photograph. :) Successfully printed in a variety of materials including Antique Bronze Matte. Thickness of the bars are approximately 1.5 mm. Available for the low-price of $29.99 in Antique Bronze only on Shapeways!
by
henryseg
The usual version of a Möbius strip has as its single boundary curve an unknotted loop. An unknotted loop can be deformed into a circle, with the strip deformed along with it.
In this version, the boundary of the strip is the circle in the middle, and the surface "goes through infinity", meaning that the grid pattern should extend outwards all the way. To save on costs, I've removed the grid lines that would require an infinite amount of plastic to print.
This was designed with Saul Schleimer.
