by
virtox
Accused of being fake, witchcraft and simply impossible..
This kinetic sculpture is inspired by the unlimited freedom of 3d printing,
it wobbles and turns with a slight movement of the hand.
Now give it a good spin or puff of air and it erupts in erratic and wild behavior.
This is the 5cm / 2" version, see the Gyro the Forms section for other shapes and sizes.
Corner stand available separately, or get the complete set below!
NEW!
Now also available as a pendant/keyfob!
In both Extra small and Small
Instructions
It is composed of four concentric cubes, each one spinning around a different axis.
The model needs some minor assembly:
Each inner cube has two knobs which need to be placed into the corresponding clamps in the parent cube. It's easiest to start with the inner most and continue outward.
And then... spin it away !
Notes
Do not be alarmed if your cube will not run smoothly at first!
Because of minor variations as a result of the printing process,
some need to wear in a little but will loosen up very quickly.
In the example video I am blowing on it to make it move, it's that smooth.
Be a little careful with (the assembly of) the Alumide version as this material is slightly less flexible/robust than the Strong & Flexible materials.
Get a complete set.
A default set consists of an Alumide Gyro the Cube and a White stand, you can change the materials in your cart later.
+ 
This kinetic sculpture is inspired by the unlimited freedom of 3d printing,
it wobbles and turns with a slight movement of the hand.
Now give it a good spin or puff of air and it erupts in erratic and wild behavior.
This is the 5cm / 2" version, see the Gyro the Forms section for other shapes and sizes.
Corner stand available separately, or get the complete set below!
NEW!
Now also available as a pendant/keyfob!
In both Extra small and Small
Instructions
It is composed of four concentric cubes, each one spinning around a different axis.
The model needs some minor assembly:
Each inner cube has two knobs which need to be placed into the corresponding clamps in the parent cube. It's easiest to start with the inner most and continue outward.
And then... spin it away !
Notes
Do not be alarmed if your cube will not run smoothly at first!
Because of minor variations as a result of the printing process,
some need to wear in a little but will loosen up very quickly.
In the example video I am blowing on it to make it move, it's that smooth.
Be a little careful with (the assembly of) the Alumide version as this material is slightly less flexible/robust than the Strong & Flexible materials.
Get a complete set.
A default set consists of an Alumide Gyro the Cube and a White stand, you can change the materials in your cart later.
+ 
by
Gijs
Do you want to order more than 1 in a single color? Check out this set of 2, or this set of 4 to save some money
This eggcup is printed on demand in laser sintered polyamide. The eggcup can hold a medium egg and due to the flexible nature of the printing material, it will adapt its shape to larger eggs as well.
This eggcup is printed on demand in laser sintered polyamide. The eggcup can hold a medium egg and due to the flexible nature of the printing material, it will adapt its shape to larger eggs as well.
by
roessnakhan
A replica of Cobb's totem from the film "Inception". As a below review has noted, and from my own version, the top works very well, and spins upwards of 90 seconds before toppling. You just might be in a dream.
by
Bathsheba
A pendant for metal printing. I have trouble believing that these are photos and not renders...something about this object feels very unlikely.
by
Bathsheba
A pendant for metal printing. I have trouble believing that these are photos and not renders...something about this object feels very unlikely.
by
QUATRO
Product Name "CLaDOS Ring". Designed by QUATRO.
Please note that this ring will come in a solid color/material! So please choose carefully! White plastic is good for DIY painting while steel and silver ones will shine your way to stardom :)
If you cannot find your size OR you just don't wear rings - try taking a look at my pendant!http://shpws.me/3NxX
Want to know more about the product?
Available in a variety of materials
The default size is ~20.32 mm in inner diameter but you can customize the size to your liking.
Click personalize to choose your US ring size.(Size support: # 8 to # 13.) Please refer to sizes at this page.
Conversion chart for ring sizes:
US Ring Size - Inside diameter
8 - 18.1mm
9 - 19.0mm
10 - 19.8mm
11 - 20.6mm
12 - 21.4mm
13 - 22.2mm
I hope you like this piece as much as I do:)
Be sure to tell a friend! Shop more at:
http://www.shapeways.com/shops/uncleQUATRO :)
Please note that this ring will come in a solid color/material! So please choose carefully! White plastic is good for DIY painting while steel and silver ones will shine your way to stardom :)
If you cannot find your size OR you just don't wear rings - try taking a look at my pendant!http://shpws.me/3NxX
Want to know more about the product?
Available in a variety of materials
The default size is ~20.32 mm in inner diameter but you can customize the size to your liking.
Click personalize to choose your US ring size.(Size support: # 8 to # 13.) Please refer to sizes at this page.
Conversion chart for ring sizes:
US Ring Size - Inside diameter
8 - 18.1mm
9 - 19.0mm
10 - 19.8mm
11 - 20.6mm
12 - 21.4mm
13 - 22.2mm
I hope you like this piece as much as I do:)
Be sure to tell a friend! Shop more at:
http://www.shapeways.com/shops/uncleQUATRO :)
by
Bathsheba
A theorem walks into a bar...
The Klein Bottle is a mathematical joke: a surface with only one side. This one feels just right in your hand and opens bottles with ease and style. Built to last in steel, it's the perfect touch for any math fan's kitchen.
The Klein Bottle is a mathematical joke: a surface with only one side. This one feels just right in your hand and opens bottles with ease and style. Built to last in steel, it's the perfect touch for any math fan's kitchen.
Yes, it really works!
Klein not-a-bottle-opener is here.
by
stop4stuff
Inspired by the well known mobius strip (discovered by August Ferdinand Möbius in 1858), an interest in the unusual, and 3D modelling, I created the Twin Rail mobius pendant.
A half shell and 3 rails form a bearing-like structure to encapsulate a train of 6mm balls in a mind-warping cage with a twisting, fascinating movement bringing to life the only pendent of its kind in the world.
Includes a 4mm loop for attaching to a necklace or leather cord.
See the photographs with retro-fitted 31 6mm chrome steel ball bearings... in the bottom photo, the balls have been heated until they 'blue'... check out the video to see how they move by clicking on the little icon below the camera above.
Also available smaller and in silver, Twin Rail Mobius Pendant - small
Note: this item is the shell alone, you will need to aquire and fit the balls (31 x 6mm or 29 x 1/4 in) as well as a suitable necklace to hang it from, a 3mm leather cord works well.
A half shell and 3 rails form a bearing-like structure to encapsulate a train of 6mm balls in a mind-warping cage with a twisting, fascinating movement bringing to life the only pendent of its kind in the world.
Includes a 4mm loop for attaching to a necklace or leather cord.
See the photographs with retro-fitted 31 6mm chrome steel ball bearings... in the bottom photo, the balls have been heated until they 'blue'... check out the video to see how they move by clicking on the little icon below the camera above.
Also available smaller and in silver, Twin Rail Mobius Pendant - small
Note: this item is the shell alone, you will need to aquire and fit the balls (31 x 6mm or 29 x 1/4 in) as well as a suitable necklace to hang it from, a 3mm leather cord works well.
by
MichielCornelissen
Both a tribute to ubiquitous, and lovely, hexagonal colour pencils, and a representation of what was coined by Joris Peels as 'combinatory manufacturing'.
Combine the connector piece with any set of 36 standard hexagonal pencils of about 7.0 mm cross section (measured at the smallest diameter). These types of sets are available around the world from many department stores and art supply stores - I’ve seen good sets for as little as 5 euro.
Examples of pencils that fit are Stabilo Aquacolor 1600, and Caran d’Ache Prismalo I, but there are many more. I’ve recently heard that in the US, Prismacolor Verithin Colored Pencils (available from Amazon and others) work well. Normal black pencils often have the same size and shape and can be used too.
If you are new to the Shapeways website: to order you will be asked to create an account (it's easy). Assembly may leave slight marks on pencils. For more information on this or other products, please visit www.michielcornelissen.com.
Combine the connector piece with any set of 36 standard hexagonal pencils of about 7.0 mm cross section (measured at the smallest diameter). These types of sets are available around the world from many department stores and art supply stores - I’ve seen good sets for as little as 5 euro.
Examples of pencils that fit are Stabilo Aquacolor 1600, and Caran d’Ache Prismalo I, but there are many more. I’ve recently heard that in the US, Prismacolor Verithin Colored Pencils (available from Amazon and others) work well. Normal black pencils often have the same size and shape and can be used too.
If you are new to the Shapeways website: to order you will be asked to create an account (it's easy). Assembly may leave slight marks on pencils. For more information on this or other products, please visit www.michielcornelissen.com.
by
lens42
Make your own slide-on macro lens for the iPhone 4 or 4S. I designed this for my iPhone 4 when I couldn't find the image quality I wanted for less than $60.
Print this model and then buy the glass lens for $4 from Surplus Shed (http://www.surplusshed.com/). The Surplus Shed part number is L4471. For some reason the search box on the Surplus Shed home page does not work with part numbers. To get to L4471, use the "Lens Finder". In the Lens Finder type:
Print this model and then buy the glass lens for $4 from Surplus Shed (http://www.surplusshed.com/). The Surplus Shed part number is L4471. For some reason the search box on the Surplus Shed home page does not work with part numbers. To get to L4471, use the "Lens Finder". In the Lens Finder type:
Lens Type: PCX, Plano Convex
Diameter: 12mm to 12mm
Focal length: 51mm to 51mm
It will get you to L4471
The lens fits in a recess in the model and is held in place with a few tiny drops of Superglue. If you get any glue on the lens it can cleaned off with nail polish remover or acetone. The lens is plano-convex (one side is flat). When inserted in the holder, the flat side of the lens faces the phone.
Note that the lens fits pretty snugly into the opening. Try fitting the lens before applying any glue. A good technique is, with the lens holder laying face-down on a table, lay the lens in position, and then push it into the recess by poking the lens with the eraser-end of a pencil. Once you know the lens fits cleanly, push it back out and put two tiny drops of superglue on opposite edges of the opening. I use a toothpick to apply the glue because squeezing the superglue directly out of the tube risks putting on too much. Then push the lens back in the same way as in the test fit.
The object pictures in the photo gallery (dime, ruler, and watch) are unedited and uncropped shots directly from my iPhone4.
This model will not slide over iPhone cases.
by
nervoussystem
A fine network of vessels defines the surface of this crescent-shaped pendant which was inspired by how veins form in leaves. The densely interconnected structure is at once airy and strong.
It is a part of Hyphae, a collection of 3D printed artifacts constructed of rhizome-like networks. Inspired by the vein structures that carry fluids through organisms from the leaves of plants to our own circulatory systems, we created a simulation which uses physical growth principles to build sculptural, organic structures. Starting from an initial seed and a surface, we grow a hierarchical network where nodes constantly branch and merge.
Watch the video below to see the the form was created.
--
If you are interested in purchasing the necklace with the chain, please buy from our website
nylon plastic version: http://n-e-r-v-o-u-s.com/shop/product.php?code=85
sterling silver version: http://n-e-r-v-o-u-s.com/shop/product.php?code=96
If you purchase directly from Shapeways it will not come with a chain.
by
cwestbrook
Please read the entire listing!
Reminiscent of Victorian filigree, this unique Designer iPhone 4 case is a durable and stylish alternative to mass produced cases on the market today. This is my newest design update! Now much more interchangeable this puzzle connection design is also more stylized and easier to put on and take off.
If you'd like each half a different color and/or design please go to my main page (www.shapeways.com/shops/cwestbrook) and order each half separately.
Designed by C Westbrook Designs in San Francisco and produced by Shapeways (based in New York and the Netherlands).
This puzzle style case will fit the iPhone 4S and all versions of the iPhone 4 (CDMA & GSM)
Click through the photos to see your color options.
The photos of the case in black highlight the unique texture of the strong and flexible material (aka laser sintered polyamide aka nylon) which in addition to adding an extra layer of interest also adds traction to keep that coveted phone in your grip!
*Please note that I'm keeping the price of this listing lower than my Etsy listings due to the case not having varnish for extra color protection. I highly recommend at least one coat of non-toxic polyurethane varnish (or something similar) so that the color can last through everyday use.*
Take a look at the video to see how to easily varnish the case yourself: http://youtu.be/eS5mp18KZrY
Multiple prints from this file have been tested on my iPhone 4, fit very well and my own case has withstood my abuse immaculately.
I designed it for easy access to all buttons, ports and controls.
The colors available are what Shapeways currently offers.
*White cases I'm offering in the polished, since it's easier to clean than the textured white. Still be aware that the white is very white, and that anything with color or dye that comes into contact with it may not be easy to remove.
*Make sure when you receive your case you note that the front puzzle pieces together and should be undone first when taking off the case.
*Only the cases I sell on my Etsy.com listings have a clear varnish added for extra protection of the color and are tried on my iPhone 4 prior to shipment. However, I'm going to only have a limited amount with limited colors each month on Etsy since dyeing and varnishing is quite time intensive.
To avoid any confusion let me clarify that if you buy a case from this store you are ordering directly from Shapeways who manufactures / 3D prints it. I can not cancel or change any orders made from this site. If you ordered a case from this listing please contact service@shapeways.com with any concerns that are unrelated to the design aspect.
Reminiscent of Victorian filigree, this unique Designer iPhone 4 case is a durable and stylish alternative to mass produced cases on the market today. This is my newest design update! Now much more interchangeable this puzzle connection design is also more stylized and easier to put on and take off.
If you'd like each half a different color and/or design please go to my main page (www.shapeways.com/shops/cwestbrook) and order each half separately.
Designed by C Westbrook Designs in San Francisco and produced by Shapeways (based in New York and the Netherlands).
This puzzle style case will fit the iPhone 4S and all versions of the iPhone 4 (CDMA & GSM)
Click through the photos to see your color options.
The photos of the case in black highlight the unique texture of the strong and flexible material (aka laser sintered polyamide aka nylon) which in addition to adding an extra layer of interest also adds traction to keep that coveted phone in your grip!
*Please note that I'm keeping the price of this listing lower than my Etsy listings due to the case not having varnish for extra color protection. I highly recommend at least one coat of non-toxic polyurethane varnish (or something similar) so that the color can last through everyday use.*
Take a look at the video to see how to easily varnish the case yourself: http://youtu.be/eS5mp18KZrY
Multiple prints from this file have been tested on my iPhone 4, fit very well and my own case has withstood my abuse immaculately.
I designed it for easy access to all buttons, ports and controls.
The colors available are what Shapeways currently offers.
*White cases I'm offering in the polished, since it's easier to clean than the textured white. Still be aware that the white is very white, and that anything with color or dye that comes into contact with it may not be easy to remove.
*Make sure when you receive your case you note that the front puzzle pieces together and should be undone first when taking off the case.
*Only the cases I sell on my Etsy.com listings have a clear varnish added for extra protection of the color and are tried on my iPhone 4 prior to shipment. However, I'm going to only have a limited amount with limited colors each month on Etsy since dyeing and varnishing is quite time intensive.
To avoid any confusion let me clarify that if you buy a case from this store you are ordering directly from Shapeways who manufactures / 3D prints it. I can not cancel or change any orders made from this site. If you ordered a case from this listing please contact service@shapeways.com with any concerns that are unrelated to the design aspect.
by
improbablecog
Resembling a bat or dragon, these biotech earrings are the wings of an alien exoform.
This piece has been released under a Creative Commons Attribution Share Alike License due to the support of the following patrons:
BJ Becker, Boon Sheridan, brepettis, Brian Hawkins, CatFord, Edvard Immonen, Edward Henderson II, GothicCharmSchool, Helen, Ian Nusbaum, Jack C, Jake von Slatt, James Ian Burns, Jess, Jezcabelle, Johnny B Jackson, Katt Tewksbury, Kim Dancy, Lastwear, Leila Smith, Libby Bulloff, Lucas Richter, Lyssa Chartrand, Malcolm Tredinnick, Marguerite Kenner, Melody Burdett, morbidity.unlimited, Nick Setten, Patrick Ball, Peter Simon, Raymond McCauley, Robert Schouwenburg, Sara Mitchell, Sigrid Ellis, strand, Sue Jackson, Theodore Minick
Because of their contributions, you are free to print this model at cost, download the original model files from my website at: http://www.improbablecog.com, use it, modify it, and even sell it, with the following restrictions:
- All derivative work must be released under the same license.
- You must attribute the original design to Noah Beasley or Improbablecog, and to the URL http://www.improbablecog.com
Also, if you do anything cool and interesting with this model, please drop me a line and let me know about it! I would love to promote your modifications, and point people your way to see it.
If you do decide to sell physical prints of this model, that's also allowed so long as you attribute the design. I would be glad to list you as a local reseller on my website as well if you let me know about it :)
That's it, otherwise have fun!
This piece has been released under a Creative Commons Attribution Share Alike License due to the support of the following patrons:
BJ Becker, Boon Sheridan, brepettis, Brian Hawkins, CatFord, Edvard Immonen, Edward Henderson II, GothicCharmSchool, Helen, Ian Nusbaum, Jack C, Jake von Slatt, James Ian Burns, Jess, Jezcabelle, Johnny B Jackson, Katt Tewksbury, Kim Dancy, Lastwear, Leila Smith, Libby Bulloff, Lucas Richter, Lyssa Chartrand, Malcolm Tredinnick, Marguerite Kenner, Melody Burdett, morbidity.unlimited, Nick Setten, Patrick Ball, Peter Simon, Raymond McCauley, Robert Schouwenburg, Sara Mitchell, Sigrid Ellis, strand, Sue Jackson, Theodore Minick
Because of their contributions, you are free to print this model at cost, download the original model files from my website at: http://www.improbablecog.com, use it, modify it, and even sell it, with the following restrictions:
- All derivative work must be released under the same license.
- You must attribute the original design to Noah Beasley or Improbablecog, and to the URL http://www.improbablecog.com
Also, if you do anything cool and interesting with this model, please drop me a line and let me know about it! I would love to promote your modifications, and point people your way to see it.
If you do decide to sell physical prints of this model, that's also allowed so long as you attribute the design. I would be glad to list you as a local reseller on my website as well if you let me know about it :)
That's it, otherwise have fun!
by
byShapeways
Draw your earrings and we will turn them into 3d.
Instructions:
1) Download Sketch Sheet
2) Scan the sketch sheet and save the image.
3) Click "Personalize" and upload the image.
4) Order your earrings in your choice of material. Shapeways will turn your drawing into a printable 3D model, and ship it to you.
You can also do it yourself with our 2D to 3D design tool, and upload a black and white .jpg. You'll just have to add your own earring hooks and get the measurements correct. Note that it doesn't support multicolored image nor it would treat the image as texture. The image will only be used for bumping the depth on the surface.
Instructions:
1) Download Sketch Sheet
2) Scan the sketch sheet and save the image.
3) Click "Personalize" and upload the image.
4) Order your earrings in your choice of material. Shapeways will turn your drawing into a printable 3D model, and ship it to you.
You can also do it yourself with our 2D to 3D design tool, and upload a black and white .jpg. You'll just have to add your own earring hooks and get the measurements correct. Note that it doesn't support multicolored image nor it would treat the image as texture. The image will only be used for bumping the depth on the surface.
by
ThreeForm
The Lotus top is a graceful form that embraces the upper body, accentuating the shoulders and clavicles. It's name comes from its unique design that blooms at the center opening, allowing the wearer to put her head through and rest it comfortably on the neck and shoulders.
A perfect fit requires a 3D body scan. Email Contact (at) ThreeFormFashion.com for more information on full service scanning and fitting.
A perfect fit requires a 3D body scan. Email Contact (at) ThreeFormFashion.com for more information on full service scanning and fitting.
by
virtox
The original Eardrops
A pair of elegant spiral droplet earrings.
Absolutely stunning in the new Premium Silver!
I recommend to use these with silver earring hooks and attach them with (7mm) split rings (not included)
These are availble at your local bijoux or jewellery store or via websites.
If you have trouble finding them, contact me with a copy of your invoice and I will make sure you get a pair!
More earrings
A pair of elegant spiral droplet earrings.
Absolutely stunning in the new Premium Silver!
I recommend to use these with silver earring hooks and attach them with (7mm) split rings (not included)
These are availble at your local bijoux or jewellery store or via websites.
If you have trouble finding them, contact me with a copy of your invoice and I will make sure you get a pair!
More earrings
by
virtox
The original Eardrops
A pair of elegant spiral droplet earrings.
Absolutely stunning in the new Premium Silver!
I recommend to use these with silver earring hooks and attach them with (7mm) split rings (not included)
These are availble at your local bijoux or jewellery store or via websites.
If you have trouble finding them, contact me with a copy of your invoice and I will make sure you get a pair!
More earrings
A pair of elegant spiral droplet earrings.
Absolutely stunning in the new Premium Silver!
I recommend to use these with silver earring hooks and attach them with (7mm) split rings (not included)
These are availble at your local bijoux or jewellery store or via websites.
If you have trouble finding them, contact me with a copy of your invoice and I will make sure you get a pair!
More earrings
by
alienology
Clothoid.A lamp is created by a mathematical curve formula and then that spline is lofted in 3d CAD software. Resulting form is parametric and adjustable in almost infinite number of combinations.
You can imagine this 3D form as afterimage of one single point in space as it moves, self-intersecting and rotating around, creating this 3D object. Whole shade form is actually one single line... wrapping around itself. Whole 3d printed light shade is created in one piece.
This lamp is available for purchase now on Shapeways. What you will get from Shapeways is 3D printed lamp shade only.
NOTE: Lamp base will be sent separately. Use "contact designer" button on upper right of this page... or send us e-mail to > info (at) alienology.com
You can imagine this 3D form as afterimage of one single point in space as it moves, self-intersecting and rotating around, creating this 3D object. Whole shade form is actually one single line... wrapping around itself. Whole 3d printed light shade is created in one piece.
This lamp is available for purchase now on Shapeways. What you will get from Shapeways is 3D printed lamp shade only.
NOTE: Lamp base will be sent separately. Use "contact designer" button on upper right of this page... or send us e-mail to > info (at) alienology.com
by
virtox
A hanging cup for your double espresso the morning after ;-)
It's in such a state that it cannot stand on it's own, so it really needs some support.
Luckily it has :-)
When you order, you will get the Hangover cup and the matching stand in glazed ceramics.
Printed Ceramics
With the current process, the round bottom on the cup will likely show some minor pits in the glazing from a small tripod it stands on during the baking.
And the bottom of the stand/saucer has rougher structure.
The rest of the glazing is fully covering, so it's safe to drink from.
Also available as a more sober version (standalone)
The cup is designed for a double espresso(60 ml), but can hold a maximum of about 90 ml.
Check out this photo of black version here
It's in such a state that it cannot stand on it's own, so it really needs some support.
Luckily it has :-)
When you order, you will get the Hangover cup and the matching stand in glazed ceramics.
Printed Ceramics
With the current process, the round bottom on the cup will likely show some minor pits in the glazing from a small tripod it stands on during the baking.
And the bottom of the stand/saucer has rougher structure.
The rest of the glazing is fully covering, so it's safe to drink from.
Also available as a more sober version (standalone)
The cup is designed for a double espresso(60 ml), but can hold a maximum of about 90 ml.
Check out this photo of black version here
by
virtox
A matching pair of earrings, resembling small twigs.
Absolutely stunning in the new Premium Silver!
These are actual photos!
Also wonderful in the other metal finished.
For example, the steel printing process adds an almost natural texture to the twigs.
Which also works very well in bronze or gold finishes!
More earrings
Silver earring hooks included, courtesy of Shapeways!
One twig is approximately 30x19x7mm.
Absolutely stunning in the new Premium Silver!
These are actual photos!
Also wonderful in the other metal finished.
For example, the steel printing process adds an almost natural texture to the twigs.
Which also works very well in bronze or gold finishes!
More earrings
Silver earring hooks included, courtesy of Shapeways!
One twig is approximately 30x19x7mm.
by
virtox
A matching pair of earrings, resembling small twigs.
Absolutely stunning in the new Premium Silver!
These are actual photos!
Also wonderful in the other metal finished.
For example, the steel printing process adds an almost natural texture to the twigs.
Which also works very well in bronze or gold finishes!
More earrings
Silver earring hooks included, courtesy of Shapeways!
One twig is approximately 30x19x7mm.
Absolutely stunning in the new Premium Silver!
These are actual photos!
Also wonderful in the other metal finished.
For example, the steel printing process adds an almost natural texture to the twigs.
Which also works very well in bronze or gold finishes!
More earrings
Silver earring hooks included, courtesy of Shapeways!
One twig is approximately 30x19x7mm.
by
LincolnK
These filigree earrings look delicate almost like lace, yet are flexible and very resilient and should last you a life time assuming a monkey doesn't eat them. They are so light that you wouldn't even know you are wearing them.
Here they are shown in the "White Strong & Flexible" material, but are also available in other colors as well as silver. They are each about 1.5 inches long and .75 inch wide.
Here they are shown in the "White Strong & Flexible" material, but are also available in other colors as well as silver. They are each about 1.5 inches long and .75 inch wide.
by
noesis
Inspired by Maori and Pacific Island bone carvings this is the second in a series of Torus based necklaces that feature a tesselating pattern that wraps the geometric form in three dimensions. At first glance the shapes may appear to be simply cut into the skin of the object but when held in your hand and rotated the repeating pattern begins to reveal itself.
The image shows the pendant printed in Stainless Steel but it is available in a variety of material choices including plastic, sterling silver and gold.
The pendant does not ship with a necklace but when combined with a simple leather cord as shown in the images it makes a very unique conversation starting peice of jewelry.
The image shows the pendant printed in Stainless Steel but it is available in a variety of material choices including plastic, sterling silver and gold.
The pendant does not ship with a necklace but when combined with a simple leather cord as shown in the images it makes a very unique conversation starting peice of jewelry.
by
baltimore
full size, 1.5" tall top, totem from Inception. more than one model was used in the film. this one is a replica of the thinner tipped model. also available in hollow for different spinning properties, like the film. wider tipped model also available in my store.
just like the ones on www.inceptiontops.com
just like the ones on www.inceptiontops.com
by
improbablecog
10gThough these earrings may resemble an xenomorphic sea creature, we can neither confirm nor deny that they were modeled after any organism living, dead, or bearing any blood relation to our board of directors.
These earrings are sized for 18 gauge piercings and should fit most people with pierced ears. If you need a different size, just ask! I have a few larger gauges already available in the shop, and can resize it to a custom gauge if it's not already there.
Disclaimer on the images: any photos labeled "polished" are stainless steel that has been hand polished with a dremel. The stainless that you order will have more of a texture to it. I haven't yet made these for myself in bronze glossy, gold plated glossy, or either types of silver, but if you want the highly polished look your best bet is going to be silver glossy.
by
GADesign
This beautiful pendant design has both inner and outer spirals, and together they represent the shape of a teardrop filled with DNA.
Premium Silver gives it more shine to make it even more beautiful !
This product has been successfully printed in all materials availible.
Premium Silver gives it more shine to make it even more beautiful !
This product has been successfully printed in all materials availible.
by
virtox
Eleganty swirling towards itself.
Larger version available here
I recommend to use these with silver earring hooks and attach them with (7mm) split rings (not included) These are availble at your local bijoux or jewellery store or via websites. If you have trouble finding them, contact me with a copy of your invoice and I will make sure you get a pair!
More earrings
Larger version available here
I recommend to use these with silver earring hooks and attach them with (7mm) split rings (not included) These are availble at your local bijoux or jewellery store or via websites. If you have trouble finding them, contact me with a copy of your invoice and I will make sure you get a pair!
More earrings
by
rinblad
A pendant in the shape of a tree, with some of the roots creating a garland around it. This unique pendant can stand on a surface or be hung in a necklace for any occasion. Currently on display in the 3DEA popup store at the Eventi hotel.
by
CLERCYSOPHIE
this bracelet is proposed in 3 size, but if you have a special size...
the dimension inside the bracelet for the medium:
62mmX43mm
2,44 inchesX1,7 inches
the dimension inside the bracelet for the medium:
62mmX43mm
2,44 inchesX1,7 inches
by
Innovo
The Mini Crowbar is both a decorative as well as practical keychain accessory (length of a typical key). It can be used for screwing, puncturing or as a keychain hanging hook.
Available in several finishes and materials (Stainless Steel, Antique Bronze Matte, Antique Bronze Glossy, Gold Plated Matte, Gold Plated Glossy). Please choose from the right.
Warning: This crowbar is size small, about 30% smaller than the medium one.
by
curvecreative
Angryman - iPhone stand headphone wrap
Want to keep your headphones tidy? Want to keep your iPhone upright while watching a movie?
The Angryman is an all in one iPhone stand, cable tidy and cable shortener. Keep your headphones on a key chain when not in use, then simply unwrap them and you can use the Angryman as an iPhone stand while you watch a movie. Perfect for trains, airplanes or even for everyday use at your desk.
Holds the iPhone at various angles and positions. Also clips on to your iPhone. Available in a range of colours.
Works with iPhone 4/iPhone 4s and iPod classic
Click here to visit our site
Or click here to keep up to date on Facebook
by
MODbot
Please note earrings are sold individually. For a pair, please order two. Email me when ordering through Shapeways and I will send out the posts.
by
elaverr
Drips: Modular Organic System #1
Collaborative project with Phil Renato & Richard Elaver. Multiple copies of six pieces snap-fit together to create a cascading form. Can be used to make jewelry, sculpture, or ...
Set includes 6 copies of 6 different pieces.
