by
chromoly
The Road Popper is a bike-mounted bottle opener that we developed for our own use and decided afterward to share. We designed it to fasten discreetly to the rails on the underside of the saddle to help keep your bike looking crisp. So far, it's worked on all the bottle caps we've tried it on. Material options are bronze infused stainless steel. Finish options are plain (on the right in the photograph), matte gold, glossy gold, matte antique bronze, and glossy antique bronze. The Road Popper is not intended for alcoholic beverages. Chromoly does not condone cycling while under the influence of alcohol.
Things You'll Need for Installation (not included with purchase)
2 - 3/8” long #6 flat head (countersunk) screws
2 - Nylon locknuts
1 - Screwdriver
1 - Needle nose pliers
Bike Requirements
Conventional bike saddle. If you're not sure if your seat is standard or not, give it a measure. The rails should be 7 mm's (0.275 inch) in diameter and roughly 44mm's (1.73 inch) apart.
At least 228mm's (9”) of space between the underside of your seat and your tire.
9mm's (3/8”) of open rail behind where the seat attaches to the seat post.
*Because this product is fabricated to order it is more expensive that it would be under normal manufacturing conditions. For this same reason it takes about 14 working days to arrive. The cost of shipping (via UPS) is included in the list price. Please note that duties and taxes may be applied to your order when it enters your country.
Things You'll Need for Installation (not included with purchase)
2 - 3/8” long #6 flat head (countersunk) screws
2 - Nylon locknuts
1 - Screwdriver
1 - Needle nose pliers
Bike Requirements
Conventional bike saddle. If you're not sure if your seat is standard or not, give it a measure. The rails should be 7 mm's (0.275 inch) in diameter and roughly 44mm's (1.73 inch) apart.
At least 228mm's (9”) of space between the underside of your seat and your tire.
9mm's (3/8”) of open rail behind where the seat attaches to the seat post.
*Because this product is fabricated to order it is more expensive that it would be under normal manufacturing conditions. For this same reason it takes about 14 working days to arrive. The cost of shipping (via UPS) is included in the list price. Please note that duties and taxes may be applied to your order when it enters your country.
by
RemivanOers
CLIP-IT for iPhone
Your charge buddy on the go.
Clip-it for iPhone converts your Euro iPhone charger to a wall dock; making sure that you can easily charge your phone at every wall socket. Unfurnished rooms, hotels and conference rooms are no longer a problem.
Clip-it lets you wind the usb cable easily around your charger while taking it with you.
Clip-it makes use of your existing Apple Dock Connector to USB Cable. Simply snap it in and lock the cable at the bottom. Clip-it is perfectly engineered to hold the latest two generations of original 30 pin Apple charging cables.
Clip-it is designed for the iPhone 4 & iPhone 4S and the included Apple USB Power Adapter (European version).
After all the excitement, an US version of Clip-it is available here!
Clip-it is manufactured by innovative 3D-printing in tough but lightweight polyamide. The surface has a fine texture. The product will be shipped in basic Shapeways packaging. Some powder residue from the 3D-printing process may be found on the product itself; if this is the case, it should be easy to clean off with small tooth sticks & brushes. When you ordered Clip-it in colour it might be wise to clean it with water under the tap, so the dyeing pigments that might still be on the product don’t colour your white Apple gadgets. For further information & support contact the Shapeways customer service.
Your charge buddy on the go.
Clip-it for iPhone converts your Euro iPhone charger to a wall dock; making sure that you can easily charge your phone at every wall socket. Unfurnished rooms, hotels and conference rooms are no longer a problem.
Clip-it lets you wind the usb cable easily around your charger while taking it with you.
Clip-it makes use of your existing Apple Dock Connector to USB Cable. Simply snap it in and lock the cable at the bottom. Clip-it is perfectly engineered to hold the latest two generations of original 30 pin Apple charging cables.
Clip-it is designed for the iPhone 4 & iPhone 4S and the included Apple USB Power Adapter (European version).
After all the excitement, an US version of Clip-it is available here!
Clip-it is manufactured by innovative 3D-printing in tough but lightweight polyamide. The surface has a fine texture. The product will be shipped in basic Shapeways packaging. Some powder residue from the 3D-printing process may be found on the product itself; if this is the case, it should be easy to clean off with small tooth sticks & brushes. When you ordered Clip-it in colour it might be wise to clean it with water under the tap, so the dyeing pigments that might still be on the product don’t colour your white Apple gadgets. For further information & support contact the Shapeways customer service.
by
curvecreative
Knotcase
A Celtic inspired iPhone case.
The KNOTCASE snaps onto your iPhone 4 or 4S and provides a slimline case that covers the back and sides of your phone. The Knot pattern on the back give an appealing texture to touch and gives your iPhone a unique look.
Click here to visit our site
Or click here to keep up to date on Facebook
by
tedk727
You can store your credit card and USB flash drive in this multi-functional case!!
Transcend JetFlash T3 Series drive fits in it.
