3d render showing product detail
1/700 US M60A2 Starship Main Battle Tank x10
Made by
Print With Shapeways
Choose Your Material
Choose your color and finish
Choose Your Material
$19.92
Choose your color and finish
Have a question about this product?
contact the designerYou must be logged in and verified to contact the designer.
Product Description
1/700 Scale Modern US M60A2 Starship Main Battle Tank.
Contains 10 highly detailed tanks.
Contains:
M60A2 Starship Main Battle Tank
The M60A2 was intended as a stop-gap solution until the projected replacement by the MBT-70. The M60A2, nicknamed the "Starship" due to its "Space Age" technology, featured an entirely new low-profile turret with a commander's machine-gun cupola on top, giving the commander a good view and field of fire while under armor but spoiling the low profile. It featured a 152 mm (6.0 in) main gun similar to that of the M551 Sheridan light tank, which fired conventional rounds as well as the MGM-51 Shillelagh anti-tank missile system. The fitting of a CBSS (closed breech scavenger system), which used pressurized air to clear the breech after each shot, solved the problem of unburnt propellant from the main gun rounds fouling the barrel and pre-detonating subsequent rounds. The M60A2 proved a disappointment, though technical advancements would pave the way for future tanks; the MBT-70, which relied on much of this technology as it was used in the M60A2, never advanced beyond prototype stage. The Shillelagh/M60A2 system was phased out from active units by 1981, and the turrets scrapped. Most of the M60A2 tanks were rebuilt as M60A3, or the hulls converted to armored vehicle-launched bridge (AVLB) vehicles..
Cleaning Information
Some part cleanup will be necessary. The 3D printing process uses a waxy substance to support certain part features during the printing process. Although the parts are cleaned by Shapeways, some waxy residue may remain. It can be safely removed with water and a mild aqueous detergent like "Simple Green" using an old, soft toothbrush, Q-tips or pipe cleaners. During the printing process, liquid resin is cured by ultraviolet light. Microscopic bits of resin may remain uncured.
Let your parts sit in direct sunlight for a few hours to fully cure the resin.
Water-based acrylic paints meant for plastics is strongly recommended. Other paints, especially enamels, may not cure on Frosted Detail 3D-printed plastics.
Use dedicated model sprue cutters to remove parts to minimise the risk of damage to parts.
Please take a look at my other items.
Painting tips and preparation
Contains 10 highly detailed tanks.
Contains:
- 10x US M60A2 Starship Main Battle Tanks
M60A2 Starship Main Battle Tank
The M60A2 was intended as a stop-gap solution until the projected replacement by the MBT-70. The M60A2, nicknamed the "Starship" due to its "Space Age" technology, featured an entirely new low-profile turret with a commander's machine-gun cupola on top, giving the commander a good view and field of fire while under armor but spoiling the low profile. It featured a 152 mm (6.0 in) main gun similar to that of the M551 Sheridan light tank, which fired conventional rounds as well as the MGM-51 Shillelagh anti-tank missile system. The fitting of a CBSS (closed breech scavenger system), which used pressurized air to clear the breech after each shot, solved the problem of unburnt propellant from the main gun rounds fouling the barrel and pre-detonating subsequent rounds. The M60A2 proved a disappointment, though technical advancements would pave the way for future tanks; the MBT-70, which relied on much of this technology as it was used in the M60A2, never advanced beyond prototype stage. The Shillelagh/M60A2 system was phased out from active units by 1981, and the turrets scrapped. Most of the M60A2 tanks were rebuilt as M60A3, or the hulls converted to armored vehicle-launched bridge (AVLB) vehicles..
Cleaning Information
Some part cleanup will be necessary. The 3D printing process uses a waxy substance to support certain part features during the printing process. Although the parts are cleaned by Shapeways, some waxy residue may remain. It can be safely removed with water and a mild aqueous detergent like "Simple Green" using an old, soft toothbrush, Q-tips or pipe cleaners. During the printing process, liquid resin is cured by ultraviolet light. Microscopic bits of resin may remain uncured.
Let your parts sit in direct sunlight for a few hours to fully cure the resin.
Water-based acrylic paints meant for plastics is strongly recommended. Other paints, especially enamels, may not cure on Frosted Detail 3D-printed plastics.
Use dedicated model sprue cutters to remove parts to minimise the risk of damage to parts.
Please take a look at my other items.
Painting tips and preparation
Details
What's in the box:
700 M60A2 Starship X10.stl
Dimensions:
Success Rate:
First To try.
What's this?
Rating:
Mature audiences only.
