NEW: Natural and Polished Copper

Click and drag to rotate
Dalek Gun-stick (pommel, #dg005) 3d printed

Not a Photo

White Natural Versatile Plastic
Dalek Gun-stick (pommel, #dg005) 3d printed
Dalek Gun-stick (pommel, #dg005) 3d printed

Not a Photo

Dalek Gun-stick (pommel, #dg005) 3d printed
Dalek Gun-stick (pommel, #dg005) 3d printed

Not a Photo

Dalek Gun-stick (pommel, #dg005) 3d printed
Dalek Gun-stick (pommel, #dg005) 3d printed

Not a Photo

Dalek Gun-stick (pommel, #dg005)

Ships as soon as 4 days
3D printed in white nylon plastic with a matte finish and slight grainy feel.

Have a question about this product?

contact the designer
You must be logged in and verified to contact the designer.
Product Description

This model is part #dg005 of my Full-sized Dalek Gun-stick. This is a screen-accurate replica of the Dalek gun-stick (featured in s9, ep1&2) of Doctor Who, weilded by Missy, Clara Oswald and the 12th Doctor. It is designed with an in-built universal joint   so it can move about and this would be VERY useful for building a full-sized Dalek as well. 


#dg001: The tip of the barrel has internal recesses cut, allowing for up to 8x 5mm LEDs to be affixed at the correct angle for maximum lighting-FX.

#dg002: The base of the barrel is set with correctly sized/ angled holes allowing them to be set with plastique or metal tubing that has been pre-bent, allowing for easy addition of outer tubes of the barrel.

#dg003: The inside part of the barrel-base is set with bolt-holes for securing the outer-base to a hollow 100mm (4” ball) while also providing an additional base, pre-set for electronics with 5mm divots set at a focal angle centred on main-barrel of the gun-stick. This allows for the addition of extra, high-powered LEDs or even Lasers.

#dg004: This cup is the female-end of a ball-joint created by modifying a hollow 100mm “contact-juggling” ball. It is set with holes for adding 10 blue 5mm LEDs, wires/tubes, set-screws (for securing to the main handle tube (standard vacuum-hose extension is recommended).

#dg005: Is the upper part of the bottom of the handle (pommel) and has holes for feeding wires/tubes, and is female-threaded and matched to the lower portion of the pommel.

#dg006: Is the lower portion of the pommel and is male-threaded and matched to the upper portion, allowing for easy access to batteries and electronics in the handle.

#dg007 is the electronics plug, which is fit to plug directly into the main handle, and accommodate a number of electronic effects.


Other parts required:

100mm (4”) hollow contact-juggling ball

2cm (od) aluminium pipe

25m of 2mm (od) aluminium tubing

standard vacuum-hose extension

8x, 5mm LEDs (green and blue mix)

10x, 5mm LEDs (blue or blue/red)

Teensy 3.1 development board (or similarly sized)


12mm 3V batteries

High-output LED relay

Black spray-paint

Silver spray-paint

Silver “rub ’n buff”

Clear gloss spray-paint

What's in the box:
Dalek Gun-stick (pommel, #dg005)
5.94 x 5.78 x 2.9 cm
Switch to inches
2.34 x 2.28 x 1.14 inches
Switch to cm
Success Rate:
First To try.
What's this?
Mature audiences only.
Sign In or Join to comment.


We're sorry to inform you that we no longer support this browser and can't confirm that everything will work as expected. For the best Shapeways experience, please use one of the following browsers:

Click anywhere outside this window to continue.