Shapeways + COVID-19  
See Solutions

Click and drag to rotate
DRAW ornament HC - mini hanger A01 3d printed

DIGITAL PREVIEW
Not a Photo

DRAW ornament HC - mini hanger A01 3d printed
DRAW ornament HC - mini hanger A01 3d printed

DIGITAL PREVIEW
Not a Photo

DRAW ornament HC - mini hanger A01 3d printed Assembled without ornament
DRAW ornament HC - mini hanger A01 3d printed Assembled without ornament

DIGITAL PREVIEW
Not a Photo

DRAW ornament HC - mini hanger A01 3d printed Assembled with a sample ornament
DRAW ornament HC - mini hanger A01 3d printed Assembled with a sample ornament

DIGITAL PREVIEW
Not a Photo

DRAW ornament HC - mini hanger A01 3d printed As manufactured (top), with connecting sprue removed (bottom)
DRAW ornament HC - mini hanger A01 3d printed As manufactured (top), with connecting sprue removed (bottom)

DIGITAL PREVIEW
Not a Photo

DRAW ornament HC - mini hanger A01 3d printed unpolished, polished, unpolished, polished and dyed
DRAW ornament HC - mini hanger A01 3d printed unpolished, polished, unpolished, polished and dyed

DIGITAL PREVIEW
Not a Photo

DRAW ornament HC - mini hanger A01 3d printed unpolished, polished, unpolished, polished and dyed
DRAW ornament HC - mini hanger A01 3d printed unpolished, polished, unpolished, polished and dyed

DIGITAL PREVIEW
Not a Photo

DRAW ornament HC - mini hanger A01 3d printed
DRAW ornament HC - mini hanger A01 3d printed

DIGITAL PREVIEW
Not a Photo

DRAW ornament HC - mini hanger A01

Made by
$6.04
3D printed in white nylon plastic with a matte finish and slight grainy feel.
QTY

Have a question about this product?

contact the designer
You must be logged in and verified to contact the designer.
Product Description

This mini ornament hanger is designed to hold a 1.4 inch long ornament with a 7mm (millimeter) diameter internal hole along this axis. You can make your own ornaments using various materials, beads, or purchase compatible ornaments in this store.

The bottom cap is connected to the main hanger with a small sprue that you need to cut off. Connecting the two parts in this way reduces the cost by eliminating multiple parts handling charges at Shapeways. Cut the sprue with a pair of small wire cutters or a strong pair of scissors where the screw thread ends. You may need to sand this end smooth a little for a proper fit.

It is likely that residual powder from fabrication will be present within the screw threads of the bottom cap and you won't be able to screw the parts together until this powder is removed. An easy way to remove this powder is to slowly screw and unscrew the two parts together in a bowl of water or under a low stream of water from a faucet, rinsing out the cap between attempts as the powder is loosened. It only takes about a minute to do this and once the residual powder is gone the cap should screw flush with the main body of the hanger.

If you want a permanent assembly you can use a small dab of glue on the screw threads to keep the cap in place on the hanger body. Once assembled there will be a small hole present in the end of the cap at the bottom of the assembled ornament. In general this will not be noticed after the ornament is hung. However, if you want to try and fill the hole you will notice that there is a very small disk and the far end of the sprue. If you carefully cut this small disk from the sprue you may be able to press fit it (or glue it) into the hole. Alternately you could fill this hole with glue or epoxy if you prefer.

----08sv2kKCQSv

Details
What's in the box:
DRAW ornament HC - mini hanger A01
Dimensions:
1.28 x 8.03 x 1.28 cm
Switch to inches
0.5 x 3.16 x 0.5 inches
Switch to cm
Success Rate:
First To try.
What's this?
Rating:
Mature audiences only.
Sign In or Join to comment.
 
 
Logo

Hello.

We're sorry to inform you that we no longer support this browser and can't confirm that everything will work as expected. For the best Shapeways experience, please use one of the following browsers:

Click anywhere outside this window to continue.