1/700 Scale Israeli Merkava IV Main Battle Tanks x10.
Contains 10 highly detailed tanks with accurate Track detail.
he Mark IV is the most recent variant of the Merkava tank that has been in development since 1999 and production since 2004. The upgrade's development was announced in an October 1999 edition of the Bamachaneh ("At the Camp") military publication. However, the Merkava Mark III remained in production until 2003. The first Merkava IVs were in production in limited numbers by the end of 2004.
When ammunition is unloaded the tank can carry up to 8 dismounted soldiers or 3 stretchers. Troops enter and leave the vehicle through the rear hatch. Removable modular armor, from the Merkava Mark IIID, is used on all sides, including the top and a V-shaped belly armor pack for the underside. This modular system is designed to allow for damaged tanks to be rapidly repaired and returned to the field. Because rear armor is thinner, chains with iron balls are attached in order to detonate projectiles before they hit the main armored hull.
It is the first contemporary tank with no loaders hatch in the turret roof, because any aperture in the turret roof increases risk of penetration by ATGMs. Tank rounds are stored in individual fire-proof canisters, which reduce the chance of cookoffs in a fire inside the tank. The turret is electrically-powered (hydraulic turrets use flammable liquid that ignites if the turret is penetrated) and "dry": no active rounds are stored in it.
- 10x Israeli Merkava IV Main Battle Tanks x10
Some features, such as hull shaping, exterior non-reflective paints (radar cross-section reduction), and shielding for engine heat plumes mixing with air particles (reduced infrared signature) to confuse enemy thermal imagers, were carried over from the IAI Lavi program of the Israeli Air Force to make the tank harder to spot by heat sensors and radar.
The Mark IV includes the larger 120 mm main gun of the previous versions, but can fire a wider variety of ammunition, including HEAT and sabot rounds like the APFSDS kinetic energy penetrator, using an electrical semi-automatic revolving magazine for 10 rounds. It also includes a much larger 12.7 mm machine gun for anti-vehicle operations (most commonly used against technicals).
The Mark IV has the Israeli-designed "TSAWS (Tracks, Springs, and Wheels System)" caterpillar track system, called "Mazkom" (Hebrew: מערכת זחלים קפיצים ומרכובים, מזקו"ם) by troops. This system is designed to reduce track-shedding under the harsh basalt rock conditions of Lebanon and the Golan Heights.
The model has a new fire-control system, the El-Op Knight Mark 4. The computer-controlled fire control system can acquire and lock onto moving targets, even airborne helicopters, while the tank itself is on the move. It includes line-of-sight stabilisation in two axes, a second-generation television sight and automatic thermal target tracker, a laser range finder, an improved thermal night vision system and a dynamic cant angle indicator. An Amcoram LWS-2 laser warning receiver notifies the crew of threats like laser-guided anti-tank missiles, which can fire smoke grenade launchers to obscure the tank from the laser beam. Electromagnetic warning against radar illumination is also installed.
The tank carries the Israeli Elbit Systems BMS (Battle Management System; Hebrew: צי"ד), a centralised system that takes data from tracked units and UAVs in theater, displays it on color screens, and distributes it in encrypted form to all other units equipped with BMS in a given theater.
The Merkava IV has been designed for rapid repair and fast replacement of damaged armour, with modular armour that can be easily removed and replaced. It is also designed to be cost-effective in production and maintenance; its cost is lower than that of a number of other tanks used by Western armies. The engine can be replaced in field conditions within 30 minutes.
The tank has a high performance air conditioning system and can even be fitted with a toilet for long duration missions.
Some part cleanup will be necessary. The 3D printing process uses a waxy substance to support certain part features during the printing process. Although the parts are cleaned by Shapeways, some waxy residue may remain. It can be safely removed with water and a mild aqueous detergent like "Simple Green" using an old, soft toothbrush, Q-tips or pipe cleaners. During the printing process, liquid resin is cured by ultraviolet light. Microscopic bits of resin may remain uncured.
Let your parts sit in direct sunlight for a few hours to fully cure the resin.
Water-based acrylic paints meant for plastics is strongly recommended. Other paints, especially enamels, may not cure on Frosted Detail 3D-printed plastics.
Use dedicated model sprue cutters to remove parts to minimise the risk of damage to parts.
Please take a look at my other items.
Painting tips and preparation