1/720 Scale DKM Bismarck 38cm (14.96") SK C/34 Guns with Blast Bags x4 as seen in 1941 after the removal of Anton's Rangefinder and as seen at time of sinking. These are the most detailed and accurate 38cm SK C/34 Guns available and have been created using plans and many reference photographs (yes, even the rivets have been counted!). This set has the Blast Bags and Barrels printed in place set at an elevation of 0º (other elevations can be requested). See My Shop for other scales.
- 4x Highly detailed turrets, Anton (no Rangefinder) Bruno, Caesar and Dora Turrets with Rangefinders
- Anton, Bruno/Caesar Turrets and Dora Turrets are unique: Anton (no Rangefinder and Higher Side Safety Rail), Bruno and Caesar (Rangefinders and Lower Side Safety Rail) and finally Dora (Rangefinders and Higher Side Safety Rail). Underside hatches on Anton and Dora are located towards the rear of the Turret whilst Bruno and Caesar are located close to the Barbette.
- Rivet detail, Periscope and Open Sighting Hatches
- Correct Stanchion placement on Turret Roofs (in lowered position) different location on Bruno and Caesar Turrets.
- Accurate underside detail including shell ejection ports and hatches.
- Digitally sculpted Blast Bags and Barrels set at an angle of 0º
Used on the famous Bismarck
class battleships, this weapon is usually - but incorrectly - referred to as being 47 calibers long, but it was actually 51.66 calibers in length. It is also sometimes mistakenly described as being a carry over from the 38 cm L/45
guns used on the World War I-era Bayern
class battleships. In reality, these guns were built to a completely new design having little in common with the older guns other than their caliber.
A modified version of these guns known as Siegfried
was widely used as coastal artillery. The best-known of these was Battery Todt, named after Armaments Minister Dr. Fritz Todt who had been killed in a plane crash. This battery consisted of four guns located near Haringzelles about 3 km (1.8 miles) east of Cap Gris-Nez and which often fired across the Straits of Dover. Four more guns were used at Oxsby (Denmark), four at Hanstead (Denmark) and three at Kristiansand (Norway).
Besides the Bismarck
, it had been planned to rearm the small battleships Scharnhorst
with these weapons. No serious work ever started for Scharnhorst
, but three turrets were under construction during the early 1940s to rearm Gneisenau
. When Gneisenau
was badly damaged in 1943, these three turrets plus an additional one originally intended for the Soviet Union were reallocated for use as coastal artillery. It was originally planned to install two of these at Cap de la Hague and the other two at Paimpol in France, but this plan was never implemented. Work on putting two of these turrets at Oxsby in Denmark was well advanced but incomplete by the end of the war.
The Soviet Union placed an order for sixteen of these guns which were intended for the battlecruisers Sevastopol
(Project 69), but no guns were ever delivered.
Constructed of loose liner, A tube with four rings shrunk over it for about two-thirds of the length from the breech, a jacket shrunk over about two-thirds of the ring layer and a breech end-piece, breech block supporting piece and a horizontal sliding breech block. Later guns had a loose liner that was removed from the breech end, but these were not universally interchangeable.
Some part cleanup will be necessary. The 3D printing process uses a waxy substance to support certain part features during the printing process. Although the parts are cleaned by Shapeways, some waxy residue may remain. It can be safely removed with water and a mild aqueous detergent like "Simple Green" using an old, soft toothbrush, Q-tips or pipe cleaners. During the printing process, liquid resin is cured by ultraviolet light. Microscopic bits of resin may remain uncured.
Let your parts sit in direct sunlight for a few hours to fully cure the resin.
Water-based acrylic paints meant for plastics is strongly recommended.
Other paints, especially enamels, may not cure on Frosted Detail 3D-printed plastics.
Use dedicated model sprue cutters to remove parts to minimise the risk of damage to parts.
Please take a look at my other items.
Painting tips and preparation