Click and drag to rotate
Adjustable LED Floodlight, N, Z or HO Scale, 16x 3d printed Adjustable lighting angle, just add a SMD LED.

DIGITAL PREVIEW
Not a Photo

Adjustable lighting angle, just add a SMD LED.
Adjustable LED Floodlight, N, Z or HO Scale, 16x 3d printed Adjustable lighting angle, just add a SMD LED.
Adjustable LED Floodlight, N, Z or HO Scale, 16x 3d printed Adjustable lighting angle, just add a SMD LED.

DIGITAL PREVIEW
Not a Photo

Adjustable LED Floodlight, N, Z or HO Scale, 16x 3d printed Directions for use after cutting the sprues.
Adjustable LED Floodlight, N, Z or HO Scale, 16x 3d printed Directions for use after cutting the sprues.

DIGITAL PREVIEW
Not a Photo

Adjustable LED Floodlight, N, Z or HO Scale, 16x 3d printed
Adjustable LED Floodlight, N, Z or HO Scale, 16x 3d printed

DIGITAL PREVIEW
Not a Photo

Adjustable LED Floodlight, N, Z or HO Scale, 16x

$21.95
3D printed in matte translucent plastic that showcases fine and intricate details.
QTY

Have a question about this product?

contact the designer
You must be logged in and verified to contact the designer.
Product Description
Scale model miniature floodlight with adjustable angle. Just add a small SMD LED (not included in this kit), for a very realistic looking tiny floodlight to light up your model railroad layout or diorama. This listing contains sixteen (16) sets of floodlights, consisting of reflector and adjustable base! Can be used for HO Scale, N Scale, or Z Scale.

The reflector snaps into the base mount via the hemispherical studs on each side of the reflector, allowing adjustment of the floodlight angle from nearly horizontal to straight upward.

Simple assembly required: The base and reflector are sprued together in a frame. Cut the sprues off after cleaning and polishing, then snap the pivots of the reflector into the holes in the base. You may want to cut the sprues of the base, at the frame end, so that the sprues themselves can be used as mounting pins. The sprue on the reflector must be cut as close to the reflector as possible, and the cut-away surface polished a bit by hand.

The floodlight reflector front aperture is 4.25 x 5.6 mm, and can fit SMD LEDs of sizes from 0402 metric through to 1206 (3216 metric). Don't forget to use epoxy glue or hotglue on the LED's connections after soldering in the wire, to avoid a short circuit with the floodlight reflector's metal body. A 1 mm hole is provided at the back of the reflector and also through the base of the mounting, to pass the LED wires through. Use a warm-white SMD LED for realistic "white" floodlight color, or an amber LED to simulate sodium vapor lamp floods used in some rail yards.

For an idea of size at your modeling scale of choice, the floodlight front aperture in these scales is approximately:
  • N Scale: 26 x 35 inch - Medium sized floodlight
  • HO Scale: 14.5 x 19 inch - Small-size floodlight
  • Z Scale: 37 x 48 inch - Large floodlight


Recommended Material: Raw Brass or Polished Brass.
Details
What's in the box:
Adjustable LED Floodlight, N, Z or HO Scale, 16x
Dimensions:
1.54 x 6.98 x 2.55 cm
Switch to inches
0.61 x 2.75 x 1 inches
Switch to cm
Success Rate:
First To try.
What's this?
Rating:
Mature audiences only.
Logo

Hello.

We're sorry to inform you that we no longer support this browser and can't confirm that everything will work as expected. For the best Shapeways experience, please use one of the following browsers:

Click anywhere outside this window to continue.