Access EOS Selective Laser Sintering
with Shapeways   

<div id="cookie_notice" class="sw-cookie-notice sw--padding-vert-4 sw--padding-hor-1 sw-dms--box-shadow--big"> <div class="sw-dms--color-white sw-grid-flex sw-grid-flex--wrap-mob sw-grid-flex--wrap--tab"> <div class="sw-cookie-notice__text--mob sw--padding-left-8 sw--font-size-14 sw-grid-flex__cell-5-7 sw-grid-flex__cell-1-1--mob sw-grid-flex__cell-1-1--tab"> We use cookies to offer you a better browsing experience, including personalized advertising. By continuing to use the site you agree to their use. <a href="/legal/privacy-statement" target="_blank">Learn more</a> </div> <div class="sw-grid-flex__cell-2-7 sw-grid-flex__cell-1-1--mob sw-grid-flex__cell-1-1--tab"> <a class="sw-dms-button noty_close sw--padding-hor-7 sw--position-absolute sw--position-right sw--margin-right-13 sw--hide-mobile sw--hide-tablet" data-sw-set-cookie="euCookie">OK</a> <a class="sw-cookie-notice__btn--mob sw-cookie-notice__btn--tab sw-dms-button noty_close sw--padding-hor-7 sw--margin-vert-3 sw--hide-desktop" data-sw-set-cookie="euCookie">OK</a> </div> </div> </div>

Click and drag to rotate
Cyma M870 airsoft heat shield (Right side) 3d printed

Not a Photo

Black Natural Versatile Plastic
Cyma M870 airsoft heat shield (Right side) 3d printed
Cyma M870 airsoft heat shield (Right side) 3d printed

Not a Photo

Cyma M870 airsoft heat shield (Right side)

Made by
Ships as soon as 8 days
3D printed in black nylon plastic with a matte finish and slight grainy feel.
Product Description
This heat shield is designed for the Cyma M870 full length (CM.350L). It consists of two clamps that clamp around the barrel and magazine tube, held together by a bolt and a nut.

This product page is about the right clamp. Make sure you also have a left clamp, which is a seperate product.

The following options are available:
- Left side clamp with heat shield
- Right side clamp

Furthermore, there is an M870 front sight available. In case you wish to install this as well, make sure to install the heat shield first, as you have to slide it on the barrel. If you have already installed the front sight, it will prevent you from sliding the heat shield on. For more information regarding the front sight, please refer to the front sight product page.

For the installation of the left and right clamp, an M5x20 bolt and M5 hex nut are required. 

Installation instructions:
- (Optional step): The left clamp features two protrusions that fit in two holes in the right clamp. This might be a very tight fit, so you may want to wear these protrusions in a bit before installing the clamps. This can be done by putting the first protrusion in the second hole and turning the clamps a bit. Keep turning the clamps until the protrusion has worn in a little bit, then repeat this for the second protrusion in the first hole. This step can be skipped, but removing the two clamps from each other might be more difficult then.

- Step 1: Slide the left clamp over the barrel and magazine tube. Make sure the rear sight starts just above halfway the forend. Do not force it further! The Cyma M870 barrel starts getting slightly thicker between the forend and the receiver, and the heat shield is not designed for this barrel diameter.
- Step 2: Insert the M5 hex nut into the recess in the right clamp. The recess is already hexagonally shaped, so the hex nut cannot rotate when inserted.
- Step 3: Slide the right clamp over the barrel until it sits at the same level as the left clamp.
- Step 4: Insert the M5x20 bolt in the left clamp and turn it in the nut.
- Step 5: Check for any movement in the two clamps. If they are still moveable, tighten the bolt.

When the heat shield has been succesfully installed, there should be a bit of space between the top and/or bottom of the magazine tube and the clamp. This is to make sure the clamp doesn't push/pull on the magazine tube.

The rear sight also features two small notches. These can be filled with paint to make aiming easier if you prefer.

Additional pictures will be added later.
What's in the box:
Cyma 870 RS Right
2 x 1.25 x 6 cm
Switch to inches
0.79 x 0.49 x 2.36 inches
Switch to cm
Success Rate:
First To try.
What's this?
Mature audiences only.
Sign In or Join to comment.


We're sorry to inform you that we no longer support this browser and can't confirm that everything will work as expected. For the best Shapeways experience, please use one of the following browsers:

Click anywhere outside this window to continue.