<div id="cookie_notice" class="sw-row sw--padding-2 sw--padding-bottom-1-force sw--text-center sw--bg-grey" > <div class="col-1-2 col-1-1--tab col--no-padding sw--display-inline-block sw--float-none sw--text-left sw--vertical-align__middle"> <p class="col-1-2 col--no-padding small">We use cookies to offer you a better browsing experience. By continuing to use the site you agree to their use. You can find out more about our cookies and read our privacy policy <a href="/legal/privacy-statement" target="_blank">here.</a></p> <div class="col-1-2 col--no-padding sw--text-center"> <div class="col-1-2 col--no-padding sw--display-inline-block sw--float-none"> <a class="sw-dms-button noty_close col-1-1 col--no-padding" data-sw-set-cookie="euCookie">OK</a> </div> </div> </div> </div>

<div class="sw-email-modal sw--display-block"> <div id="emailModalContentContainer"> <span class="noty_close sw--position-absolute sw--position-right sw--padding-top-3 sw--padding-right-3 icon-cancel sw--opacity-8"></span> <div class="sw-row"> <div class="sw-email-modal__copy sw--position-relative sw--display-block sw--padding-vert-4"> <p class="last sw--font-size-16">Get the newest 3D printed drone accessories right in your email. Subscribe now!</p> <form action="/register/email-signup" class="sw-email-modal__signup sw--position-relative" data-confirmation="emailConfirmationModal" data-sw-email-modal-form> <input type="text" class="sw-email-modal__signup-input sw--input-height__medium" placeholder="Email address" name="email" /> <input type="hidden" class="sw-email-modal__signup-input" name="location" value="/product/3UK4LEN6W/qav-400-uhf-antenna-bracket" /> <input type="hidden" class="sw-email-modal__signup-input" name="confirmation" value="emailConfirmationModal" /> <input type="submit" class="btn-primary" value="Sign Up" /> <div id="emailModalFormError" class="text-error" style="display:none"></div> </form> </div> </div> </div>

Click and drag to rotate
QAV 400 UHF Antenna Bracket 3d printed

Not a Photo

QAV 400 UHF Antenna Bracket 3d printed
QAV 400 UHF Antenna Bracket 3d printed

Not a Photo

QAV 400 UHF Antenna Bracket

Made by
3D printed in white nylon plastic with a matte finish and slight grainy feel.
Product Description
This is a mounting bracket I printed off for my QAV400. The bottom plate has 2 sets of 4 holes which I think were originally intended for mounting landing gear, but otherwise go unused.

You'll need 4 - M4 nuts and screws. I purposely made the nut hole a little undersized because the nuts get melted in place to lock them in permanently. Use a soldering iron to heat the nut and press into place.

This mounting bracket was part of a series of modifications to relocate the UHF transmitter as far away from the other RF emitting sources. Scanning with a spectrum analyzer showed slightly better noise levels below the rig than above the rig which is what led to this being located where it is.

One other note - it's hard to make out in the photo but I soldered in a 300ma 5v step down regulator from Pololu into the power distribution board and routed the wires right to the bracket so you can power the receiver from a separate power source.

Quite a few folks have reported dropouts and motor cutoffs so the current recommendation is to power the UHF receiver separately from the CC3D. If that's not possible, power the receiver directly from a 5v source, then connect a set of jumper cables from the receiver to the power pins of the CC3D, not the other way around.

QAV 400 UHF Antenna Bracket by Mochaboy, available under a Creative Commons - Attribution - Share Alike license.
What's in the box:
QAV 400 UHF Antenna Bracket
4.14 x 8.5 x 0.6 cm
Switch to inches
1.63 x 3.35 x 0.24 inches
Switch to cm
Success Rate:
First To try.
What's this?
Mature audiences only.
Sign In or Join to comment.


We're sorry to inform you that we no longer support this browser and can't confirm that everything will work as expected. For the best Shapeways experience, please use one of the following browsers:

Click anywhere outside this window to continue.