Ariel Lemon

fakebusker83

3D modeler, Designer, Product designer, Artist, Maker
I'm an enthusiastic toy customizer.

592
Followers
28
Following
fakebusker83's
POTP Swoop G1 Styled Missiles
fakebusker83 @Linkxvii Here's the link to the model in BHDA material. It's not tested, so I can't vouch for how the 'pen clip' will perform...Best regards! https://www.shapeways.com/product/SED3X9MJA/potp-swoop-g1-styled-missiles-bhda?key=d38c07782c6c36b1403bce2022145f90
POTP Snarl G1 Styled Blaster
fakebusker83 @Linkxvii Black premium will still retain a somewhat grainy texture, and I believe its black is darker than BHDA. You can try the BHDA version on the link here: https://www.shapeways.com/product/XCXKLB762/potp-snarl-g1-blaster-bhda?key=1b4e6f92f90e124fbe7225d03bdce7af
fakebusker83 @Linkxvii Hi there, unfortunately I won't recommend BHDA as it doesn't seem to work well with the rotating joint in this model. I can create a variant that uses a simpler 5mm peg instead to avoid breakage, or remove the rotation feature altogether. Would you prefer that?
fakebusker83 @olliefu Do you mean the ring holding both pieces together? You can use basic wire snips or nail clippers. Thanks!
POTP Voyager Starscream Null Rays
fakebusker83 @Teletraan My head canon Thundercracker is a darker navy blue :) But anyway, those are really nice repaints!
fakebusker83 @Teletraan he’s so pretty. Thank you so much for sharing!
fakebusker83 @Teletraan oh SWEET PAINT JOB! :D
fakebusker83 @Mikedie they look great! Thanks for sharing :) Have a Merry Christmas and Happy Holidays Mike! Any issues with them I should know about?
Skyquake head For CW Silverbolt
fakebusker83 @crystalis Sure thing. You can access the 1 piece model at: https://www.shapeways.com/product/4LJR6FMYR/cw-predator-skyquake-head-1-piece?key=d501d9172e0471ecc6eb6f565bf49a01
fakebusker83 @crystalis Alas, Shapeways doesn't allow printing of this model in Purple Strong Flexible due to the small size of the faceplate. I can however fuse both face and helm together as a one piece print, but it might be harder to paint. Would you prefer that?
POTP Volcanicus 'Extinction' sword set
fakebusker83 @Arazyr Sure thing, Polished Metallic Plastic option is now open. However I personally avoid that material due to its tolerance issues. Have a try and let me know how it turns out?
POTP Hun-grr Blaster Accessory
fakebusker83 @unicron75 here’s another shot with an older CW styled hand. Same thing with the fingers.
fakebusker83 @unicron75 the ‘guard’ does not interfere with combiner fingers at all. It rests on them and the blaster still points straight. Does this help?
fakebusker83 @unicron75 It's a 5mm peg so I think it should be quite compatible!
fakebusker83 @ManlyYams Hi there, oh goodness no, the bars aren't supposed to be there. It's my mistake. The model has not been corrected. Do you live in continental USA? Can I send you a replacement? Thank you so much for the comment and feedback!
Fusion Cannon for TR Megatron
fakebusker83 @ababilheira hi there, I personally use modelling lacquer paint, Gunze Sangyo Mr Color brand. The finish is up to personal taste, but flat or semi-gloss works for me best.
fakebusker83 @ababilheira Hi there, I'd actually recommend printing in White Strong Flexible Polished and painting it yourself. Black Strong Flexible doesn't undergo the polishing process and hence the print lines will be heavily visible.
POTP Battletrap Weapon Accessories
fakebusker83 Hi @wildkickwolf sure thing. I've added links to the individual accessories. You may find them in the description above.
Krok Head for Titans Return Compatibility
fakebusker83 @gabantoniocabrera yup! 'Tis done. Let me know if you have any issues since BHDA is tricky to work with.
fakebusker83 commented on POTP Dreadwind Blasters by fakebusker83
March 16, 2018
POTP Dreadwind Blasters
fakebusker83 @rapierdragon Thank you for the in depth feedback. Yes, 2mm sprues are strong, but I feel it safer to err on the side of caution as results can fluctuate quite a bit between prints. I have models with 1.5mm sprues come apart before, and 2mm feels the most reliable, so to speak. Perhaps you've lucked out and gotten a good, strong print!
fakebusker83 @pjkelly No problem. Thank you!
fakebusker83 @pjkelly Hi there, yes they come attached by a couple of sprue rods, so snipping them will result in a visible white spot. I made sure to place these spots at the bottom of the blaster handle and main chasing, so they won't be visible at most angles.
fakebusker83 commented on POTP Sludge G1 Styled Blaster by fakebusker83
February 18, 2018
POTP Sludge G1 Styled Blaster
fakebusker83 Hi @HarleyQuinade, sure thing you can check out this link: https://www.shapeways.com/product/J9KS3UHA6/g1-styled-blaster-for-potp-sludge-paired-set
fakebusker83 commented on POTP Voyager Starscream Feet by fakebusker83
February 17, 2018
POTP Voyager Starscream Feet
fakebusker83 @pedrop have a look! https://instagram.com/p/BfTWY4GnTn9/
POTP Slug G1 Sword (Full Crossguard)
fakebusker83 @iamthevetrep Hey there, I've just prepared a version with a half cross guard in case you're still interested in a G1 Slug sword. (https://www.shapeways.com/product/S7ZH4XTJC/g1-sword-for-potp-slug-half-crossguard)
fakebusker83 @iamthevetrep you’re right, his forearm design does prevent him from holding the sword straight. Fortunately his wrists tilt downwards to accommodate the crossguard.
TR Overlord Powermaster Backpacks
fakebusker83 @Arazyr oh sure! I’ll have a go at it!
fakebusker83 @Abejorro97 hi there, no the panels won’t close with the backpacks installed. I’ll have to make them really flat to fit, and they might be too difficult to pull out.
MP Seeker hands (peg wrist variant)
fakebusker83 @tfyaujta Hi there, sorry to hear about the accident. Can you show me a picture of the crack in better light? Did it occur when you're assembling a finger or something else?
fakebusker83 @tfyaujta Yup! They do hold 5mm peg accessories :)
fakebusker83 commented on POTP Grimlock G1 Sword by fakebusker83
January 19, 2018
POTP Grimlock G1 Sword
fakebusker83 @thecrimsonrid3r It is to reduce material usage and ultimately reduce costs of printing. As of Jan 20th 2018 today the current version is still under testing so I am not sure how flimsy it is. Once I have the models in hand I can make a better decision on whether to reinforce the thinner parts. Blade thickness is currently 1.5 mm. I might widen it to 2 mm thick.
fakebusker83 @thecrimsonrid3r hi there, do you happen to have a photo of the issue?
fakebusker83 @Hyoumaru hi there, I’ve activated the option for BHDA. Have fun and let me know how that turns out!
fakebusker83 commented on TFP Thirsty x 3 by fakebusker83
December 19, 2017
TFP Thirsty x 3
fakebusker83 @Heckfire Hi! Why yes, these are all compatible, no worries. Since they all use 3mm compatible pegs and ports, you can use cyberverse accessories on them as well.
fakebusker83 commented on G1 Styled Helm for TR Galvatron by fakebusker83
December 11, 2017
G1 Styled Helm for TR Galvatron
fakebusker83 @ababilheira Thanks for sharing! :)
fakebusker83 commented on Atomic Obliterator (Lite) by fakebusker83
December 5, 2017
Atomic Obliterator (Lite)
fakebusker83 @AoeHound301 Oh! This is new...It looks nice on him!
TFP Megatron's fusion cannon (dark energon)
fakebusker83 @awesometjgreen Hi there, this model is not designed to work with FE Megatron, unfortunately. We also didn't work on guns for voyager Optimus, but maybe another artist on Shapeways did. You can have a look?
fakebusker83 commented on Trivia the Cruciverbalist by fakebusker83
November 25, 2017
Trivia the Cruciverbalist
fakebusker83 @ajfantine Thank you for your feedback. Let's get in touch.
Krok Head For Combiner Wars deluxe Air Raid
fakebusker83 @lkavadas Here you go. Have a look at this: https://www.shapeways.com/product/F6CMFYJNC/krok-head-for-titans-return-compatibility
1 piece Hammer for Bumblebee (The Last Knight)
fakebusker83 @providedjam hi there, Shapeways prints in single colour for almost all their materials. Are you referring to the hammer being silver and yellow? For that you’ll have to paint the model yourself, alas.
fakebusker83 commented on Heads for CW 'Overlord' by fakebusker83
October 10, 2017
Heads for CW 'Overlord'
fakebusker83 @trence5 hi there, at present these heads don’t work with the TR Leader, alas.
Next
Logo

Hello.

We're sorry to inform you that we no longer support this browser and can't confirm that everything will work as expected. For the best Shapeways experience, please use one of the following browsers:

Click anywhere outside this window to continue.