iphone headphone winch reel! This is a miniature winch which is a reel for headphones. It is specifically designed to hold an iphone or ipod at the base. Just insert headphone jack through the hole in the reel drum and wind it up using the lever. Plugin the Jack to your iphone or ipod which fit in the bottom area.

Cool down with this ultra-efficient mini-fan! This impeller was designed based on CPU cooling fans. It was the most efficient impeller design in its class. It was designed specifically for this motor: Dayton® No. 4M299 Fan/Blower Motor- 3.3 inch Diameter, Shaded Pole, Open 1/70 horsepower, 3000 RPM, Clockwise Rotation Facing Shaft Volts 60Hz: 115  Full-Load Amps: 0.7 Shaft Dimensions: 1/4 x 1 1/8inches (additional motor information can be obtained from the following URL: http://www.grainger.com/Grainger/items/4M299)

Can be resized to order! | Shown as size 9 | ID is 19.0 mm (.748" ID) Hope you enjoy!

ipod touch dashboard mount allows ipod to be plugged in to 1/4" auxillary jack and charging cable simultaneously | Either cable can be connected, one at a time, if needed | ipod touch dashboard mount shown with apple headphone and charge cables attached (cables not included) | "Blank" for holding ipod touch without cable is sold separately | The "blank" will allow the ipod to mount without a cable attached | This base is designed to be used with common velcro - attach velcro to desired location on dashboard and on back of mount | With velcro installed, ipod can be attached to mount and entire mount can removed from dashboard as needed | Hope you enjoy!

custom text ring shown in size 10 | send a message with what you want your ring to say | I'll create the ring and it will be available for you to purchase | total charachter "limit" is approximately 50 (around ring), but even if it is over that, send what you want on your ring and we will work it out. | Important: send your ring size | Hope you enjoy!

Can be resized to order! | Shown as size 9 | ID is 19.0 mm (.748" ID) | Hope you enjoy!

Customizable nameplate | shown with "MECHNOLOGY TECH" | send message with desired name plate lettering | thicker options available

Customizable nameplate | shown with "MECHNOLOGY TECH" | send message with desired name plate lettering | thinner options available (less material & less volume)

Pen holder which plugs into usb slots | Assemble per images | Two configurations: pen parallel and perpendicular to usb slot | Hope you enjoy!

Can be resized to order! | Shown as size 9 | ID is 19.0 mm (.748" ID)

Can be resized to order! | Shown as size 10 | ID is 19.8 mm (.780" ID) | Designed to be an interesting wedding band replacement for men | Several advantages: No worries about it getting lost (cheap & replaceable) | Also, no worries about being difficult to remove if your hand swells up due to injury (titanium rings cannot be removed with normal surgical equipment while these can be removed with simple tools. e.g. pliers can break the ring if you squeeze axially) | Hope you enjoy!

Insert headphone jack through this spool and then plug jack into ipod or iphone. Reel in headphones as needed. Storage is convenient with headphones wound in reel.

iphone headphone winch reel! This is a miniature winch which is a reel for headphones. It is specifically designed to hold an iphone or ipod at the base. Just insert headphone jack through the hole in the reel drum and wind it up using the lever. Plugin the Jack to your iphone or ipod which fit in the bottom area.

Can be resized to order! | Shown as size 10 | ID is 19.8 mm (.780" ID)

Pen holder which plugs into usb slots | Assemble per images | Two configurations: pen parallel and perpendicular to usb slot | Hope you enjoy!

Can be resized to order! | Shown as size 9 | ID is 19.0 mm (.748" ID) Hope you enjoy!

This is a pen holder which is for computer monitors and anywhere else a free usb slot is open where pen storage would be convenient | Bracket plugs into USB port. Only 1 bracket needs to be plugged in to hold up pin rack | Use middle connection for best results as shown in image | Twist lock feature on brackets to attach to pen-holder rack | Parts are printed flat & disassembled to save volume (cost) as shown in photos.

This is a pen holder which is for walls/desks/pin-boards | Special grooves for pinning up with pins/tacks | Twist lock feature on brackets to attach to pen-holder rack | Parts are printed flat & disassembled to save volume (cost) as shown in photos.

This item attaches to the top of a lighter so it can be heated up for soldering. i.e. an ultra-portable solder tool | 0.8 mm round tip | tip optimized to be longer while receiving more heat contact | This does not include the lighter. The lighter is a BIC World, Classic, Maxi.

This item attaches to the top of a lighter so it can be heated up for soldering. i.e. an ultra-portable solder tool | 2.4 mm round tip | tip optimized to be longer while receiving more heat contact | This does not include the lighter. The lighter is a BIC World, Classic, Maxi.

This item attaches to the top of a lighter so it can be heated up for soldering. i.e. an ultra-portable solder tool | 2.4 mm wide tip | tip optimized to be longer while receiving more heat contact | This does not include the lighter. The lighter is a BIC World, Classic, Maxi.

This item attaches to the top of a lighter so it can be heated up for soldering. i.e. an ultra-portable solder tool | 2.4mm wide tip | This is Does not include the lighter. The lighter is a BIC World, Classic, Maxi.

This item attaches to the top of a lighter so it can be heated up for soldering. i.e. an ultra-portable solder tool | 1.6 mm round tip | tip optimized to be longer while receiving more heat contact | This does not include the lighter. The lighter is a BIC World, Classic, Maxi.

This item attaches to the top of a lighter so it can be heated up for soldering. i.e. an ultra-portable solder tool | 0.8 mm wide tip | tip optimized to be longer while receiving more heat contact | This does not include the lighter. The lighter is a BIC World, Classic, Maxi.