We found 11 products by iconic.am
by
iconic.am
The iconic.am case is available at www.iconic.am.
This base is designed to be mounted to round tubes such as handlebars and seatposts.
We will separately send you the following items:
1: an 8-32 acorn nut, two hex machine screws and two thumb nuts
2: two pre-cut pieces of adhesive backed rubber to glue to the inside faces of the mount
Please forward your Shapeways order payment confirmation to us at shapeways@iconic.am, so that we can send you the parts.
to assemble: Separate the two pieces by cutting the thin connectors between the parts. Press the nut into the plastic using a set of pliers. Push the hex screws into the main body of the mount. Remove the backing from the rubber and stick one piece to each part of the mount. to mount: assemble the mount around the bar and tighten the thumb nuts.
This base is designed to be mounted to round tubes such as handlebars and seatposts.
We will separately send you the following items:
1: an 8-32 acorn nut, two hex machine screws and two thumb nuts
2: two pre-cut pieces of adhesive backed rubber to glue to the inside faces of the mount
Please forward your Shapeways order payment confirmation to us at shapeways@iconic.am, so that we can send you the parts.
to assemble: Separate the two pieces by cutting the thin connectors between the parts. Press the nut into the plastic using a set of pliers. Push the hex screws into the main body of the mount. Remove the backing from the rubber and stick one piece to each part of the mount. to mount: assemble the mount around the bar and tighten the thumb nuts.
by
iconic.am
The iconic.am case is available at www.iconic.am.
This base is designed to be mounted to the 1in strap that is common on most backpacks. It's what the sternum strap mounts to.
We will separately send you an 8-32 acorn nut
Please forward your Shapeways order payment confirmation to us at shapeways@iconic.am, so that we can send you the parts.
to assemble: press the nut into the plastic using a set of pliers.
to mount: place the clip around the sternum strap and press to close.
This base is designed to be mounted to the 1in strap that is common on most backpacks. It's what the sternum strap mounts to.
We will separately send you an 8-32 acorn nut
Please forward your Shapeways order payment confirmation to us at shapeways@iconic.am, so that we can send you the parts.
to assemble: press the nut into the plastic using a set of pliers.
to mount: place the clip around the sternum strap and press to close.
by
iconic.am
The iconic.am case is available at www.iconic.am.
This base is designed to be mounted onto standard tripods (1/4-20 thread).
We will separately send you an 8-32 acorn nut.
Please forward your Shapeways order payment confirmation to us at shapeways@iconic.am, so that we can send you the parts.
to assemble: press the nut into the plastic using a set of pliers. mount to your tripod as you would any other camera.
This base is designed to be mounted onto standard tripods (1/4-20 thread).
We will separately send you an 8-32 acorn nut.
Please forward your Shapeways order payment confirmation to us at shapeways@iconic.am, so that we can send you the parts.
to assemble: press the nut into the plastic using a set of pliers. mount to your tripod as you would any other camera.
by
iconic.am
The iconic.am case is available at www.iconic.am.
This base is designed to be mounted to curved surfaces using 2-sided tape or sugru.
We will separately send you 3 items:
1: an 8-32 acorn nut
2: a pre-cut piece of 3M VHB 2-sided tape
3: a packet of sugru (hand formable silicone rubber adhesive)
Please forward your Shapeways order payment confirmation to us at shapeways@iconic.am, so that we can send you the parts.
to assemble: press the nut into the plastic using a set of pliers.
to mount: use the 3M tape on smooth surfaces such as a skateboard helmet, or the sugru on weird shaped surfaces such as a vented bike helmet
This base is designed to be mounted to curved surfaces using 2-sided tape or sugru.
We will separately send you 3 items:
1: an 8-32 acorn nut
2: a pre-cut piece of 3M VHB 2-sided tape
3: a packet of sugru (hand formable silicone rubber adhesive)
Please forward your Shapeways order payment confirmation to us at shapeways@iconic.am, so that we can send you the parts.
to assemble: press the nut into the plastic using a set of pliers.
to mount: use the 3M tape on smooth surfaces such as a skateboard helmet, or the sugru on weird shaped surfaces such as a vented bike helmet
by
iconic.am
The iconic.am case is available at www.iconic.am.
To get steady footage and creative angles while skating, snowboarding, etc. the pole cam is a must. This base is designed to be mounted into 3/4 in schedule 40 PVC pipe, available at any hardware store.
We will separately send you an 8-32 acorn nut.
Please forward your Shapeways order payment confirmation to us at shapeways@iconic.am, so that we can send you the parts.
to assemble: press the nut into the plastic using a set of pliers. Press the adapter into your tube.
The length of pipe is up to you, we found that 36" is a good balance of reach and weight. We recommend adding a slip cap to the open end for neatness.
To get steady footage and creative angles while skating, snowboarding, etc. the pole cam is a must. This base is designed to be mounted into 3/4 in schedule 40 PVC pipe, available at any hardware store.
We will separately send you an 8-32 acorn nut.
Please forward your Shapeways order payment confirmation to us at shapeways@iconic.am, so that we can send you the parts.
to assemble: press the nut into the plastic using a set of pliers. Press the adapter into your tube.
The length of pipe is up to you, we found that 36" is a good balance of reach and weight. We recommend adding a slip cap to the open end for neatness.
by
iconic.am
The iconic.am case is available at www.iconic.am.
To get steady footage and creative angles while skating, snowboarding, etc. the pole cam is a must. This base is designed to be mounted into a tube with a .875in inner diameter.
We will separately send you an 8-32 acorn nut.
Please forward your Shapeways order payment confirmation to us at shapeways@iconic.am, so that we can send you the parts.
to assemble: press the nut into the plastic using a set of pliers. Press the adapter into your tube.
Our favorite tube is part # 45001-2 at www.rockwestcomposites.com, but any tube with a .875" inner diameter will work. The length is up to you, we found that 36" is a good balance of reach and weight.
If carbon fiber tubing is a little fancy for you, then we also have a schedule 40 PVC pipe adapter available in this shapeways store.
To get steady footage and creative angles while skating, snowboarding, etc. the pole cam is a must. This base is designed to be mounted into a tube with a .875in inner diameter.
We will separately send you an 8-32 acorn nut.
Please forward your Shapeways order payment confirmation to us at shapeways@iconic.am, so that we can send you the parts.
to assemble: press the nut into the plastic using a set of pliers. Press the adapter into your tube.
Our favorite tube is part # 45001-2 at www.rockwestcomposites.com, but any tube with a .875" inner diameter will work. The length is up to you, we found that 36" is a good balance of reach and weight.
If carbon fiber tubing is a little fancy for you, then we also have a schedule 40 PVC pipe adapter available in this shapeways store.
by
iconic.am
The iconic.am case is available at www.iconic.am.
Low profile case adapter, ideal for use on skateboards. It faces iconic.am's lens towards the mounting surface.
We will separately send you a 1/8", 1.25" long stainless pin.
Please forward your Shapeways order payment confirmation to us at shapeways@iconic.am, so that we can send you the parts.
to assemble: press the pin through the plastic using a vise or by starting it in by hand and then pressing down on the housing with the pin against a hard surface.
Low profile case adapter, ideal for use on skateboards. It faces iconic.am's lens towards the mounting surface.
We will separately send you a 1/8", 1.25" long stainless pin.
Please forward your Shapeways order payment confirmation to us at shapeways@iconic.am, so that we can send you the parts.
to assemble: press the pin through the plastic using a vise or by starting it in by hand and then pressing down on the housing with the pin against a hard surface.
by
iconic.am
The iconic.am case is available at www.iconic.am.
This base is similar to the stock flat sticky base, but is shorter for mounting in tighter spots. It can be mounted using 2-sided tape or sugru.
We will separately send you 3 items:
1: an 8-32 acorn nut
2: a pre-cut piece of 3M VHB 2-sided tape
3: a packet of sugru (hand formable silicone rubber adhesive)
Please forward your Shapeways order payment confirmation to us at shapeways@iconic.am, so that we can send you the parts.
to assemble: press the nut into the plastic using a set of pliers.
to mount: use the 3M tape on smooth surfaces such as a skateboard helmet, or the sugru on weird shaped surfaces such as a vented bike helmet
This base is similar to the stock flat sticky base, but is shorter for mounting in tighter spots. It can be mounted using 2-sided tape or sugru.
We will separately send you 3 items:
1: an 8-32 acorn nut
2: a pre-cut piece of 3M VHB 2-sided tape
3: a packet of sugru (hand formable silicone rubber adhesive)
Please forward your Shapeways order payment confirmation to us at shapeways@iconic.am, so that we can send you the parts.
to assemble: press the nut into the plastic using a set of pliers.
to mount: use the 3M tape on smooth surfaces such as a skateboard helmet, or the sugru on weird shaped surfaces such as a vented bike helmet
by
iconic.am
The iconic.am case is available at www.iconic.am.
Vibration isolated AMPS standard mount. Replace your handlebar mount GPS with your iPhone. This mount is compatible with the AMPS bolt pattern commonly found on GPS and similar devices. It can mount your iPhone in landscape or portrait mode, and will work with mounting plates up to 1/4" in thickness. This mount is vibration isolated to protect your iPhone from vibration (e.g. motorcycle engines.)
This mount is very compact when used with our low profile case adapter (available in this shop.)
Note: This mount is identical to our standard AMPS mount, but is more expensive because we provide vibration isolators. If you do not need vibration isolation, that model is also available in this shop.
We will separately send an 8x32 acorn nut, threadlocker and a set of 4x vibration isolating studs, nuts and bolts.
Please forward your Shapeways order payment confirmation to us at shapeways@iconic.am, so that we can send you the parts.
to assemble:
1: press the short bolts into the mount in the preferred bolt pattern (portrait or landscape.)
2: apply a dab of loctite threadlocker to each bolt and thread the vibration isolators onto the bolts.
3: place the mount and isolator assembly onto the AMPS compliant plate and thread on the locknuts (don't use threadlocker here)
Vibration isolated AMPS standard mount. Replace your handlebar mount GPS with your iPhone. This mount is compatible with the AMPS bolt pattern commonly found on GPS and similar devices. It can mount your iPhone in landscape or portrait mode, and will work with mounting plates up to 1/4" in thickness. This mount is vibration isolated to protect your iPhone from vibration (e.g. motorcycle engines.)
This mount is very compact when used with our low profile case adapter (available in this shop.)
Note: This mount is identical to our standard AMPS mount, but is more expensive because we provide vibration isolators. If you do not need vibration isolation, that model is also available in this shop.
We will separately send an 8x32 acorn nut, threadlocker and a set of 4x vibration isolating studs, nuts and bolts.
Please forward your Shapeways order payment confirmation to us at shapeways@iconic.am, so that we can send you the parts.
to assemble:
1: press the short bolts into the mount in the preferred bolt pattern (portrait or landscape.)
2: apply a dab of loctite threadlocker to each bolt and thread the vibration isolators onto the bolts.
3: place the mount and isolator assembly onto the AMPS compliant plate and thread on the locknuts (don't use threadlocker here)
by
iconic.am
The iconic.am case is available at www.iconic.am.
AMPS standard mount. Replace your mounted GPS with your iPhone. This mount is compatible with the AMPS bolt pattern commonly found on GPS and similar devices and the variety of mounts available from rammount.com. It can mount your iPhone in landscape or portrait mode, and will work with mounting plates up to 1/2" in thickness.
This mount is very compact when used with our low profile case adapter (available in this shop.)
Note: This mount is identical to our vibration isolated AMPS mount, but without vibration isolators. If you need vibration isolation for a uses such as a motorcycle handlebar, that model is also available in this shop.
We will separately send an 8x32 acorn nut and a set of four 8-32 nuts and bolts.
Please forward your Shapeways order payment confirmation to us at shapeways@iconic.am, so that we can send you the parts.
to assemble:
1: press the bolts into the mount in the preferred bolt pattern (portrait or landscape.)
2: place the mount and isolator assembly onto the AMPS compliant plate and thread on the locknuts
AMPS standard mount. Replace your mounted GPS with your iPhone. This mount is compatible with the AMPS bolt pattern commonly found on GPS and similar devices and the variety of mounts available from rammount.com. It can mount your iPhone in landscape or portrait mode, and will work with mounting plates up to 1/2" in thickness.
This mount is very compact when used with our low profile case adapter (available in this shop.)
Note: This mount is identical to our vibration isolated AMPS mount, but without vibration isolators. If you need vibration isolation for a uses such as a motorcycle handlebar, that model is also available in this shop.
We will separately send an 8x32 acorn nut and a set of four 8-32 nuts and bolts.
Please forward your Shapeways order payment confirmation to us at shapeways@iconic.am, so that we can send you the parts.
to assemble:
1: press the bolts into the mount in the preferred bolt pattern (portrait or landscape.)
2: place the mount and isolator assembly onto the AMPS compliant plate and thread on the locknuts
by
iconic.am
The iconic.am case is available at www.iconic.am.
Egg timer mount for rotating time lapse photography:
This mount is for the hardware hackers only. You will need to buy additional hardware, including the key piece: an Ikea Stam egg timer.
Use two pieces of 1/2" wide 2-sided tape (3M Scotch Outdoor Mounting tape works the best) to stick the feet of this mount to the egg timer. You will also need an 8-32 acorn nut and two more pieces of 2 sided tape to hold the egg timer.
Egg timer mount for rotating time lapse photography:
This mount is for the hardware hackers only. You will need to buy additional hardware, including the key piece: an Ikea Stam egg timer.
Use two pieces of 1/2" wide 2-sided tape (3M Scotch Outdoor Mounting tape works the best) to stick the feet of this mount to the egg timer. You will also need an 8-32 acorn nut and two more pieces of 2 sided tape to hold the egg timer.
Shop Details
Expertise
- Product designer
- Maker
Shop Sections
