For experienced modders only. DO NOT USE WITH STOCK HERCULES GREY HIPS..please use with stainless hips also for order on this site. Use R/C car gear grease. Design has a no-refund policy/zero margin.

This is an upgrade kit that makes G1 Predaking taller. It adds thigh extensions and a waist extension for Razorclaw. The waist extension requires disassembly of the figure. There are also arm extensions for Razorclaw to improve his proportions. This is the second version of the parts and are considered BETA. Please order at your own risk. Assemble parts carefully, do not force and sand where needed. Feedback most welcome.

**PLEASE ORDER POLISHED FOR OPTIMIUM FIT AND FINISH, Minor adjustments to fit may be required due to production variances** It's finally here, the ENTIRE kit to fully upgrade your Hercules for much better aesthetics and proportions. Includes Thigh and Wing Extensions, special elbows for the Rage arms, face and fist covers for Exgraver, a face cover for Neckbreaker, Thigh missiles, a special 2-part drill that installs in either hand or splits to install on forearms, filler pieces for Herc's sides, wider wheels for Heavy Labor, crane mounts and locks, and crotch flaps. 26 parts in all!!! Makes Herc 16mm / 5/8" taller!!! Thanks to volume pricing, this is a tremendous deal at just over $4/part. To finish the parts, I recommend light cleaning and sanding of all parts, a light grey primer, 'GM Silver' for the thighs, and "Tamiya X15 acryllic mixed with yellow, gold and white, applied with a bit of water in thin coats" and black RIT dye for the elbows.

For experienced modders only. Replacement hips for Hercules. Some use of a dremel may be required. Use R/C car gear grease. Please also order nylon D-rings (perhaps grab more than one set) There is a no-refund policy due to design issues on this part at this time...Thanks.

PLEASE ORDER POLISHED FOR BEST FITMENT AND SURFACE QUALITY This is the original kit which includes Thighs (which add 16mm / 5.8" of height), Wing Extensions (10mm width per side), a crane mount (so the crane can mount along Herc's back and a crane lock as well as the famous elbows that enhance the Rage kit by mounting the forearms inline with the treads. All parts have been revised for Polished. Minor sanding and fitting may be needed. I recommend a light grey primer with bright automotive silver (i.e. standard GM automobile silver) for the thighs and a mix of Tamiya X15 green acryllic with a good helping of testors acryllic gold, some white and a tiny bit of yellow to match Herc's green. NOTE: Purple is not a direct match, good for base color only

Please order polished for best possible fit and finish. NOTE: Minor sanding may be needed for optimum fit due to production variances. This kit allows you to mount Hercules' crane along his back and lock the crane spool in place if you wish to add a string. 5mm pegs allow the part to be held as a sheild when in individual robot modes.

**PLEASE ORDER POLISHED FOR BEST POSSIBLE FIT AND FINISH. Minor adjustments to fit may need to be made due to production variances...if you have any questions please ask**. Finally, polished thighs! New two piece design is lower cost! Make your Herc 16mm / 5.8" taller. Works with Standard and RAGE Hercules...NOTE: Purple is not an exact match of Hercules Purple, suitable for base coat only

These side pieces 'fill out' the sides of Hercules, especially with the Rage kit. They double as wrench-weapons when in individual robot modes. Please order polished for best possible fit.

These are face covers for Exgraver and Neckbreaker. They work in both vehicle and limb modes for Hercules, with or without the Rage kit. Please order polished for best fit. NOTE: Image also shows fist covers for Exgraver, available separately...

These are thigh missiles for Hercules and Heavy Labor. Please order polished for best possible fit.

**IMPORTANT This is for V3 owners only, Thighs, wing extensions and crane mount NOT INCLUDED** **PLEASE ORDER POLISHED FOR BEST FIT, minor sanding or adjustment may be needed due to production tolerances** This kit is made for owners of the original V3 kit who would like all the new parts at one low price. Features facecovers for Neckbreaker and Exgraver, fist covers for Exgraver, waist fillers, wheels for Heavylabor, new crotch flaps for Heavylabor, thigh missiles, and 2-piece combining drill. NOTE: There are some filler parts in this kit to bring the cost down....

These are slightly wider crotch flaps for Heavy Labor for a more filled out look at the waist. Requires some disassembly of Heavy Labor to install. Please order polished for best results.

These fists will improve the look of your Razorclaw figure by adding length to the arms. NOTE: Without the Razorclaw waist extension in the Predaking kit, you will need to fully extend the width of the arms and/or slightly rotate them for the hands to clear Razorclaw's yellow thighs in Robot mode.