ICU is selling 6 products in Hobby section
by
ICU
Reliably cut extra SFG's for your UMX Sbach. Now V2.0, I increased the length of the LOW PROFILE SFG. It now has almost the same surface area as the OEM Small SFG, but with a lower profile.
This kit contains both the LARGE and SMALL templates, based off the OEM SFG's, for superior rudder control. And an experimental LOW PROFILE template, for enhanced rudder control.
This kit contains both the LARGE and SMALL templates, based off the OEM SFG's, for superior rudder control. And an experimental LOW PROFILE template, for enhanced rudder control.
by
ICU
A small Anemometer to measure the wind speeds while at the field flying. Spinning cup arm assy. Dia. is 3 15/16"(10cm).
D.I.Y. instructions and pictures comming soon.
All that is needed to complete is:
1pc. - #6-32 x 1/2" (min.) or M4 x 15mm (min.)
1pc. - 0.25"(6mm) Dia. x 0.062"(1.5mm) Thick Magnet
1pc. - Bicycle Computer (Most Brands). (The wheel sensor must not be taller than 20mm)
{Program the computer for a rolling diameter of 783mm.}
(Optional):
1pc. - 1/2" Dia. x 3~4' length of a PVC pipe. Stick one end of pipe in the ground and place the Anemometer on the other.
If you have any questions please feel free to send me a message.
D.I.Y. instructions and pictures comming soon.
All that is needed to complete is:
1pc. - #6-32 x 1/2" (min.) or M4 x 15mm (min.)
1pc. - 0.25"(6mm) Dia. x 0.062"(1.5mm) Thick Magnet
1pc. - Bicycle Computer (Most Brands). (The wheel sensor must not be taller than 20mm)
{Program the computer for a rolling diameter of 783mm.}
(Optional):
1pc. - 1/2" Dia. x 3~4' length of a PVC pipe. Stick one end of pipe in the ground and place the Anemometer on the other.
If you have any questions please feel free to send me a message.
by
ICU
**All pictures shown are of the "Lite" version mounts. These mounts are exactly the same, except without the window.**
Comes with 4 mounts, enough to hang 2 small planes. Or possibly up to 4 planes, if they are hung from the prop or landing gear. (up to an approx. 24~28" Wing Span)
I have succesfully hung a 32" 3D Profile Plane (6.5oz. w/o battery) and a 18" EDF Jet (8.9oz. w/o battery), using only one mount and a piece of bent coat hanger. (see other pictures) Although this way of mounting the 3D plane is not very good for the wings, It is just possible.
I designed them to use #6 Drywall Screws to attach a piece of "coat hanger" or "music wire" to the wall or ceiling. (The wire should be bent into an "L" shape from one side and a "U" from the other. Place the short end of the "L" on the wall {pointing down} and secure with screws. After securing both "short end L" sections, you can now place your plane's wings on the long ends of the "L's". Now your plane is up and out of the way.)
Comes with 4 mounts, enough to hang 2 small planes. Or possibly up to 4 planes, if they are hung from the prop or landing gear. (up to an approx. 24~28" Wing Span)
I have succesfully hung a 32" 3D Profile Plane (6.5oz. w/o battery) and a 18" EDF Jet (8.9oz. w/o battery), using only one mount and a piece of bent coat hanger. (see other pictures) Although this way of mounting the 3D plane is not very good for the wings, It is just possible.
I designed them to use #6 Drywall Screws to attach a piece of "coat hanger" or "music wire" to the wall or ceiling. (The wire should be bent into an "L" shape from one side and a "U" from the other. Place the short end of the "L" on the wall {pointing down} and secure with screws. After securing both "short end L" sections, you can now place your plane's wings on the long ends of the "L's". Now your plane is up and out of the way.)
by
ICU
Comes with 4 mounts, enough to hang 2 small to medium planes. Or possibly up to 4 planes, if they are hung from the prop or landing gear. (up to an approx. 34~38" Wing Span)
**These mounts are untested. I will update as soon as I recieve mine.**
I designed them to use #8~10 Drywall Screws to attach a piece of "coat hanger" or "music wire" to the wall or ceiling. (The wire should be bent into an "L" shape from one side and a "U" from the other. Place the short end of the "L" on the wall {pointing down} and secure with screws. After securing both "short end L" sections, you can now place your plane's wings on the long ends of the "L's". Now your plane is up and out of the way.)
**Some detail might be lost when printing in metals or gray robust**
**These mounts are untested. I will update as soon as I recieve mine.**
I designed them to use #8~10 Drywall Screws to attach a piece of "coat hanger" or "music wire" to the wall or ceiling. (The wire should be bent into an "L" shape from one side and a "U" from the other. Place the short end of the "L" on the wall {pointing down} and secure with screws. After securing both "short end L" sections, you can now place your plane's wings on the long ends of the "L's". Now your plane is up and out of the way.)
**Some detail might be lost when printing in metals or gray robust**
by
ICU
Comes with 4 mounts, enough to hang 2 small planes. Or possibly up to 4 planes, if they are hung from the prop or landing gear. (up to an approx. 24~28" Wing Span)
I have succesfully hung a 32" 3D Profile Plane (6.5oz. w/o battery) and a 18" EDF Jet (8.9oz. w/o battery), using only one mount and a piece of bent coat hanger. (see other pictures) Although this way of mounting the 3D plane is not very good for the wings, It is just possible.
**These are the lite Version. I removed some excess material to make it a little cheaper**
I designed them to use #6 Drywall Screws to attach a piece of "coat hanger" or "music wire" to the wall or ceiling. (The wire should be bent into an "L" shape from one side and a "U" from the other. Place the short end of the "L" on the wall {pointing down} and secure with screws. After securing both "short end L" sections, you can now place your plane's wings on the long ends of the "L's". Now your plane is up and out of the way.)
I have succesfully hung a 32" 3D Profile Plane (6.5oz. w/o battery) and a 18" EDF Jet (8.9oz. w/o battery), using only one mount and a piece of bent coat hanger. (see other pictures) Although this way of mounting the 3D plane is not very good for the wings, It is just possible.
**These are the lite Version. I removed some excess material to make it a little cheaper**
I designed them to use #6 Drywall Screws to attach a piece of "coat hanger" or "music wire" to the wall or ceiling. (The wire should be bent into an "L" shape from one side and a "U" from the other. Place the short end of the "L" on the wall {pointing down} and secure with screws. After securing both "short end L" sections, you can now place your plane's wings on the long ends of the "L's". Now your plane is up and out of the way.)
by
ICU
Optional weather vane for use with the D.I.Y. mind meter.
Assembly instructions comming soon.
Assembly instructions comming soon.
Shop Details
Shop Sections
