Version 1.0

This is a pair of articulated hands for the FOC voyager Soundwave figure! Every digit is articulated and the thumb is on a ball joint. The hands have a wrist swivel joint and is designed to easily replace the originals.

This design is modified from the previously designed 14mm posable fists, and functions similarly. These hands will fit the FOC Soundblaster and FOC Blaster figures as well.

This model has not been tested. Strong Flexible material is recommended.

Version 2.0

This is a set of 6 spider legs for the Beast Hunters cyberverse Airachnid figure! The legs extend out from a central mount that attaches to the 3mm port on her back, and each leg has 4 joints for maximum posability!

Additionally, each leg ends off with a claw that can hold compatible 3mm peg weapons. This set of legs is sturdy enough to support the weight of the cyberverse figure.

This model is successfully tested in Black Strong Flexible and that material is recommended.

Just added: a photo of an awesome leader Starscream custom using these hands, done by my good friend Encline!

Note: I have tested these hands in both Strong Flexible and Detail material, and I conclude SF is the better alternative as it is much hardier and is able to stand up to the wear and tear of the joints. Detail material is disappointingly unable to do so, and the joints are too loose for comfort. For better surface detail, I highly recommend ordering the hands in White Strong Flexible Polished!

A pair of posable hands for the Revenge of the Fallen Leader Starscream figure!

Each order comes with 2 hands with interchangeable core, giving customizers the freedom to mount the core with a 5mm socket to allow arming of compatible weapons, or the lack of a socket for an aesthetically pleasing appearance.

Each hand possesses 3 posable fingers on ball-joints, bending in 2 places, and 2 thumbs also mounted on ball joints.

The wrist too, is on a ball joint, allowing for dynamic poses on a already awesome figure.

Due to the nature of the installation, this model is for experienced customizers only. You need a dremel, cutting knife and a strong epoxy sculpt. These are for removing the existing hands and installing the wrist ball-joints in their place.

Flickr set is here.
TFW2005 thread is here. (Includes assembly instructions)

 A pair of wrists, hands and add-on accessories for the ROTF voyager Starscream figure! Every finger is posable on ball joints, and the wrists are double-jointed for maximum posability!

These hands can collapse neatly in jet mode for a more satisfying, streamlined appearance. Additionally, the add-on weapons can be mounted on the underwing hardpoints. There are so many ways to customise this set!

Flickr set is here.
TFW2005 thread is here. (Includes assembly instructions)

Version 2.0

 Yup, here's my first offering for upgrading your DOTM figures! There has been many awesome customs of Sentinel Prime lately, and you'll only need a couple of expressive, posable fists to make them complete!

Version 1.0

Edit: The world famous Transformers customizer Encline has put up a review of this pair of Optimus Prime's hands! In the video he shows the assembly process, installation, and he finally showcases how well the hands worked, holding weapons and giving various poses! Again, I am very honoured to have my designs reviewed in such an awesome manner. Link is located below!

A pair of hands for ROTF Leader class Optimus Prime! These hands are fully articulated with ball joints on the fingers, thumbs and wrists! Also, they are capable of holding 5mm peg mechtech weapons as well as his original rifle!

Recommended material: Strong Flexible

Version 1.5

A pair of posable hands for use with the ROTF leader Optimus Prime figure! The wrists, thumbs and all fingers are ball-jointed. Additionally, the back of each hand unfolds to form a deadly knuckle duster!

This design is recommended in Strong Flexible material.

TFW Radicon thread here.
Flickr gallery here.

In response to requests from friends and supporters, I did a revised version of my posable hands for the DOTM leader Sentinel Prime figure, this time to be much more movie accurate and with even more detail!

Each hand is articulated at the wrist with a ball joint. The fingers each are double jointed, and even the thumbs are on ball joints. The leader's hands are big enough for me to design it such that it can hold weapons without relying on the tension of the finger joints, so you can pose them in many different ways, with many different weapons. Transformation is very much possible, I made sure of that (yay!). Just make sure the fingers are arranged properly, kinda similar to how the original fingers were. IssuesThe test sample has a loose wrist ball-joint. This issue is not fixed as I used the same measurements as my other hands. Those hands came out with tight joints so it beats me why this sample was loose. Use super glue to tighten if necessary. As the joints are all designed to be sturdy and the pieces are kinda chunky, I will not recommend ordering them in Detail material or Frosted Ultra Detail material as they will most likely break under that pressure. However, I still will make these materials available for those who are picky about their surface detail. Buyer beware!

TFW2005 thread here. (Includes assembly instructions)
Flickr gallery here.

Version 2.0

A pair of posable hands for the Dark of the Moon Leader class Ironhide figure! Each finger is double-jointed, the wrists and thumbs are also ball-jointed, and the hands still fit behind the windscreen in his alt mode!

Not for casual collectors. You will need a dremel and some skill to install these hands.

I recommend these to be printed in Strong Flexible material for maximum reliability.

Radicon thread here. (With installation instructions)
Flickr gallery here.

Done for a request, this is a set of 3 pairs of hands inspired by the Dreads from DOTM.
They are meant to be installed on the DOTM leader Ironhide figure.

The set includes:
- 3 pairs of wrist pieces
- 3 pairs of palms
- 28 standard fingers/thumbs
- 2 Crankcase spikes
- 2 Crowbar middle fingers.

Recommended in Strong Flexible.

 BadBabeBot head for Transformers deluxe Terradive figure.

Version 2.0

A custom femme head for the HFTD Terradive mold! Be sure to order it in Frosted Ultra Detail to take full advantage of the light piping!

Version 1.5

Edit: Added spare fingers. Just in case!
A variant of the hands done for the Masterpiece Seeker figure, but this version has its wrist joint replaced with a ridged peg. The wrist peg is 5mm in diameter and peg section is 7mm long.

3 spare fingers (the middle section) for your posable MP Seeker hands. I did this as that piece is the most fragile of the model, prone to snapping at the joint if you are not careful during assembly. This only applies for Frosted Ultra Detail.

I am not earning any profit from this. I just want everybody to have a perfect set of hands. Oh, and the MP Seeker hand model already includes 2 spare finger pieces. This model is for the extreme emergency.

A pair of hands with individually posable fingers and thumbs. Knuckle width 14mm, wrist ball diameter 5mm.

This model has been successfully tested in White Strong Flexible.

Version 1.5

This is a pair of giant sized posable hands meant for any of your large, combiner or city-former scaled projects! These hands are extremely posable, with each digit segmented into 3 joints and capable of creating almost every conceivable pose!

The wrist is a ball joint socket, and it works with any 10 mm diameter ball joint. This includes LEGO® Bionicle ball joints. You can also get a compatible wrist adaptor from Shapeways here.

The hands each measure 68 mm from wrist to fingertip, and 40 mm across the knuckles.

This model is successfully tested in White Strong Flexible.

Flickr gallery here.
TFW2005.com thread here.

Version 2.0

THIS VERSION IS UNTESTED. TEST PRICES AVAILABLE. ORDER AT YOUR OWN RISK.

This is the "Casúr" head for the TFP: Prime RID deluxe Vehicon figure! This head comes in two components: the face piece and light pipe.

Version 1.0 has been tested in Frosted Ultra Detail and experienced some fit issues. Version 2.0 is fixed but untested. Frosted Ultra Detail is recommended.

Version 2.0

THIS VERSION IS UNTESTED. TEST PRICES AVAILABLE. ORDER AT YOUR OWN RISK.

This is the "Corvus" head for the TFP: Prime RID deluxe Vehicon figure! This head comes in three components which includes the face piece, light pipe and goggle attachments. Yes, this head comes with goggles!

Some flexing is required to mount the goggles onto the head. Take care during assembly not to over-flex.

Version 1.0 has been tested in Frosted Ultra Detail and experienced some fit issues. Version 2.0 is fixed but untested. Frosted Ultra Detail is recommended.

Version 2.0

THIS VERSION IS UNTESTED. TEST PRICES AVAILABLE. ORDER AT YOUR OWN RISK.

This set contains all 3 individual head designs of the D.R.E.A.D series.

Version 1.0 has been tested in Frosted Ultra Detail and experienced some fit issues. Version 2.0 is fixed but untested. Frosted Ultra Detail is recommended.

Version 1.0

This is a set of components to form 6 'dreadacles' of 30 units each. In total this set contains:
- 6 x 3mm peg unit
- 6 x 3mm port unit
- 168 x basic dreadacle units
- 6 x cyber-kunai

The main dreadacle segment attaches together via balljoints, and the cyber-kunai pegs into a 3mm port at one end. The other end of the dreadacle is a 3mm peg which can be used on all compatible ports. Feel free to alter the length of each dreadacle to your taste.

Equally distributed, the length of each dreadacle is about 16 cm.

For their intended usage, it is recommended to get the D.R.E.A.D 6X3 Backpack model as well.
For length extension, you can look at the D.R.E.A.D Dreadacle 120 unit booster pack.

This model has been successfully tested in Strong Flexible.

Version 1.2

A piece to replace the back piece/trunk of the TF: Prime RID deluxe Vehicon figure. This upgrade will give the Vehicon two extra 5mm ports and one 3mm port on his back to mount additional accessories.

In car mode, the ports will resemble aggressive looking rocket boosters!

This model has been successfully tested in White Strong Flexible and Frosted Ultra Detail.

Version 1.0

A piece to replace the back piece/trunk of the TF: Prime RID deluxe Vehicon figure. This upgrade will give the Vehicon six extra 3mm ports on his back to mount additional accessories.

In car mode, the 6 ports will resemble aggressive looking rocket boosters!

This model has been successfully tested in White Strong Flexible and Frosted Ultra Detail.

Version 1.0

A replacement head for the Generations War for Cybertron deluxe Cliffjumper figure! The model comes in 2 pieces; a head piece and a light pipe piece. Simply pop the latter into the back of the head piece and attach the whole thing to the figure's neck ball joint. No screws or adhesives needed.

This model is successfully tested on Frosted Ultra Detail.