Done for a request, this is a set of 3 pairs of hands inspired by the Dreads from DOTM.
They are meant to be installed on the DOTM leader Ironhide figure.

The set includes:
- 3 pairs of wrist pieces
- 3 pairs of palms
- 28 standard fingers/thumbs
- 2 Crankcase spikes
- 2 Crowbar middle fingers.

Recommended in Strong Flexible.

Version 2.0

This pair of hands are specially designed for the Human Alliance Bumblebee figure! Not only are they extremely posable, the right arm cannon feature of the figure is preserved and everything fits nicely in alt mode!

TFW2005 thread here (with assembly instructions.)

Version 1.5

This is a set of weapons designed to be used with Dark of the Moon voyager Sentinel Prime figure! Each set includes a pair of swords, a hand blaster and a shield. The swords and blaster can be stored at the back of the shield, which in turn can be stored at the back of the figure or on top of its alt mode!

All the weapons and shield are held by 5mm pegs, so they are compatible with many other figures.

This set is tested on White Strong Flexible.

Version 1.5 This blaster is an enlarged version of the one included in the voyager Sentinel Prime weapon set, this time sized to fit the leader class Sentinel Prime figure!

Includes a 3mm c-clip to allow storage on Sentinel's many 3mm railings.

This model is untested.

Version 1.5
Edit: Tightened hand peg, similar to original version.

An enlarged version of the "Feuer Frei" scatter blaster, now lengthened to 13 cm to better fit leader class figures. The handle is still a 5mm compatible peg.
There are still 2 auxiliary pegs on the side for storage, as well as areas where 3mm c-clips can attach to.

This model is untested.

Version 1.5
Edit: Thickened front spikes for greater endurance and strength.

A vicious, spiky hand cannon to arm your alien robotic ground troops with! Made to be as accurate to the movie footage as possible, this design contains hoses, armour plates and other features that cannot be easily replicated with conventional molding techniques.

Printing in Strong Flexible is recommended due to the amount of fine, fragile details.

This model is tested in WSF.

Version 1.5

A pair of claw weapons for the HFTD Tomahawk figure! This design is inspired by the appearance of the Wrecker Whirl in the IDW comics, and are meant to emulate his 4 fingered claw design.

Each finger-claw has 2 ball joints and are mounted on a wrist section which can rotate 360d as well.

Because of the fist-sheath that is supposed to hide the original hands of the figure, these claws are not suitable for all figures. As a rough guideline, the width of the figure's forearm should be equal to or narrower than 12mm. Also, the figure should be able to hold a 5mm peg handle.

 BadBabeBot head for Transformers deluxe Terradive figure.

Version 1.5

Edit: I've added spare finger pieces in case any of your fingerjoints break during assembly. This happens when you are printing in Frosted Ultra Detail.
A pair of posable hands for the Masterpiece Seeker figure! This is compatible with MP-3 Starscream and all his subsequent repaints. Each hand has a wrist ball joint, thumb ball joints, and 4 individual posable fingers!

This model has been tested successfully with White Strong Flexible and Frosted Ultra Detail. FUD fingers have a 25% chance of breaking so please be careful during assembly.

Pegged wrist variant here.

Version 1.5

Edit: Added spare fingers. Just in case!
A variant of the hands done for the Masterpiece Seeker figure, but this version has its wrist joint replaced with a ridged peg. The wrist peg is 5mm in diameter and peg section is 7mm long.

Version 2.0

This set is specially designed for the War for Cybertron deluxe Megatron figure! It consists of a pair of forearms and a vambrace which are fully capable of working with the figure's transformation and they look great in both robot and vehicle modes!

These hands have individually posable fingers and thumbs, and are capable of holding compatible 5mm peg accessories.

This set is also compatible with the Atomic Obliterator .


Radicon thread here.

Flickr gallery here.

A pair of hands with individually posable fingers and thumbs. Knuckle width 14mm, wrist ball diameter 5mm.

This model has been successfully tested in White Strong Flexible.

Version 1.0

A compatible wrist ball joint adaptor for the Extremely Enormous Extremities posable hands sets.
The ball joint diameter is 10 mm.

Flickr gallery here.
TFW2005.com thread here.

Version 2.0

THIS VERSION IS UNTESTED. TEST PRICES AVAILABLE. ORDER AT YOUR OWN RISK.

This is the "Casúr" head for the TFP: Prime RID deluxe Vehicon figure! This head comes in two components: the face piece and light pipe.

Version 1.0 has been tested in Frosted Ultra Detail and experienced some fit issues. Version 2.0 is fixed but untested. Frosted Ultra Detail is recommended.

Version 2.0

THIS VERSION IS UNTESTED. TEST PRICES AVAILABLE. ORDER AT YOUR OWN RISK.

This is the "Chet" head for the TFP: Prime RID deluxe Vehicon figure! This head comes in three components which includes the face piece, light pipe and posable lower jaw.

Some flexing is require to mount the lower jaw onto the head. Take care during assembly not to over-flex.

Version 1.0 has been tested in Frosted Ultra Detail and experienced some fit issues. Version 2.0 is fixed but untested. Frosted Ultra Detail is recommended.

Version 2.0

THIS VERSION IS UNTESTED. TEST PRICES AVAILABLE. ORDER AT YOUR OWN RISK.

This set contains all 3 individual head designs of the D.R.E.A.D series.

Version 1.0 has been tested in Frosted Ultra Detail and experienced some fit issues. Version 2.0 is fixed but untested. Frosted Ultra Detail is recommended.

Version 1.0

This is a Spiker blaster favoured for use by the D.R.E.A.D team. It is held by a 5mm peg handle. This model has been successfully tested in White, Strong Flexible.

Version 1.0

This is a pair of Slicer accessories favoured for use by the D.R.E.A.D team. Each Slicer has one fixed and one movable handle peg for multiple ways of holding, and the front claw assembly has 4 ball joints for maximum posability.

This model has been successfully tested in White, Strong Flexible.

Version 1.0

This is a set of components to form 6 'dreadacles' of 30 units each. In total this set contains:
- 6 x 3mm peg unit
- 6 x 3mm port unit
- 168 x basic dreadacle units
- 6 x cyber-kunai

The main dreadacle segment attaches together via balljoints, and the cyber-kunai pegs into a 3mm port at one end. The other end of the dreadacle is a 3mm peg which can be used on all compatible ports. Feel free to alter the length of each dreadacle to your taste.

Equally distributed, the length of each dreadacle is about 16 cm.

For their intended usage, it is recommended to get the D.R.E.A.D 6X3 Backpack model as well.
For length extension, you can look at the D.R.E.A.D Dreadacle 120 unit booster pack.

This model has been successfully tested in Strong Flexible.

This is the booster pack for the D.R.E.A.D 6 X Dreadacles set, containing 120 basic dreadacle units. This can add up to 57 cm in length to your dreadacles.

This model has been successfully tested in Strong Flexible.

Version 1.0

A piece to replace the back piece/trunk of the TF: Prime RID deluxe Vehicon figure. This upgrade will give the Vehicon six extra 3mm ports on his back to mount additional accessories.

In car mode, the 6 ports will resemble aggressive looking rocket boosters!

This model has been successfully tested in White Strong Flexible and Frosted Ultra Detail.

Version 1.6

A pair of blasters for Transformers Prime deluxe Arcee figure. They are specially designed to be mounted on her forearm 5mm peg sockets, and they have an additional socket for her blade weapons to be mounted underneath.

Also, they can be mounted on the side of her bike mode by using the same attachment to the blades.

Printing in Detail material is recommended.

Version 2.0

A pair of show accurate blasters for TF: Prime RID deluxe Arcee! These blasters are held by 5mm pegs, and they also have side peg holes for them to be mounted on the side of her bike mode!

This set is for those who have already owned the previously released "Spider Stinger" blades, and wanted just the blasters.

Version 1.0 is tested in White Strong Flexible. The current version 2.0 is untested.
Buyer beware.

A fusion cannon and blade replacement for the TF: Prime Powerizer Megatron figure! This set includes a fusion cannon and an forearm armour attachment with a fold-out blade.

All components need to be assembled, and the cannon is designed to accommodate an LED circuit.

For the "Dark Energon" variant, click here

This model has been successfully tested and recommended in White Strong Flexible material.