8'' Mt. Rainier Terrain Model, Washington, USA

8'' Mt. Rainier Terrain Model, Washington, USA 3d printed Art Sculptures Photo of model, looking North
Photo of model, looking North
8'' Mt. Rainier Terrain Model, Washington, USA 3d printed Art Sculptures Radiance rendering
8'' Mt. Rainier Terrain Model, Washington, USA 3d printed Art Sculptures Radiance rendering
Radiance rendering
8'' Mt. Rainier Terrain Model, Washington, USA 3d printed Art Sculptures Photo with Wiimote for scale
8'' Mt. Rainier Terrain Model, Washington, USA 3d printed Art Sculptures Photo with Wiimote for scale
Photo with Wiimote for scale
3d Model Viewer
8'' Mt. Rainier Terrain Model, Washington, USA 3d printed Art Sculptures
8'' Mt. Rainier Terrain Model, Washington, USA 3d printed Art Sculptures
8'' Mt. Rainier Terrain Model, Washington, USA 3d printed Art Sculptures Photo of model, looking North
8'' Mt. Rainier Terrain Model, Washington, USA 3d printed Art Sculptures Photo of model, looking North
Photo of model, looking North
8'' Mt. Rainier Terrain Model, Washington, USA 3d printed Art Sculptures Photo of model, looking East
8'' Mt. Rainier Terrain Model, Washington, USA 3d printed Art Sculptures Photo of model, looking East
Photo of model, looking East

Mt. Rainier's 14,417-foot peak is visible for nearly one hundred miles on a good day, and is an iconic feature of the horizon in Western Washington. A strato-volcano, Mt. Rainier's present cone is one half-million years old and covered with glaciers that amount to nearly one cubic mile of ice. Though it last erupted in 1854. Rainier is still potentially active, and because of its proximity to the densely-settled Seattle-Tacoma area and the massive amount of ice that would be melted during an eruption, it poses more risk than any other volcano in the US.

This model showcases Rainier's summit and steep cone, and because we used the latest USGS high-resolution data, minor features as little as 100' wide are modeled. Little Tahoma dominates the Eastern slope, the summit crater is obvious, and crevasses in the mountain's major glaciers are even visible. If you can't see Rainier every day, or if you can, but only from one angle, put this mountain on your desk or coffee table and enjoy it whenever you like.

Model scale is 1:62700
Model covers an area approximately 7.8 by 7.8 miles
Altitudes covered: 4109' to 14417'
There is never any vertical exaggeration in TinyMtn models.

Click here for more sizes.
Click here for other 8" models.

TinyMtn models are most affordable in the "White Strong and Flexible" and "Sandstone" materials. This model is in "White Strong and Flexible." When you receive the model, there may still be Nylon dust on it from the printing process. Use either an airbrush, canned dust blower, or a soft old toothbrush to remove this dust. Do not get the "White Strong and Flexible" material wet, and don't prime it or use any oil-based paints on it. You can safely seal it with Polycrylic or a similar water-based clear spray sealant. Read more about this popular material here.

The "Frosted Detail" material will show more detail, but is semi-transparent and has an uneven surface texture when unpainted (due to the orientation of the model when Shapeways prints it). It may show up feeling a little greasy and with small crystals in crevasses. Clean those off by soaking the model in warm (but not hot) soapy water and brushing with an old toothbrush. To get the surface to an even matte finish, spray with a few light coats of sandable primer (white automotive primer works), and then do a baking soda grit-blast.

These models have been optimized for the above materials, and are not offered in other materials for strength or cost reasons. If you need one in another material, please contact us and we'll try to accommodate your request.

(C) 2013 TinyMtn (TM)
Model created using GDAL, NetPBM, Gmsh, Carve, MeshLab, and other custom software
Source of digital elevation data: U.S. Geological Survey
The USGS home page is http://www.usgs.gov/

cm: 20 w x 20 d x 6.578 h
in: 7.874 w x 7.874 d x 2.59 h

Comments

 
OK, I had to write a blog post about this one... http://www.shapeways.com/blog/archives/1883-3D-Printed-Memories-of-a-Mountain.html
January 17, 2013, 3:17 am
WOah, that actually looks SO MUCH better as a photograph than as a render... It looks like an artifact.
January 17, 2013, 2:59 am
@duann Just added two photos of this model, plus some of Zion @100mm and Yosemite @150mm. Hope you like them!
January 17, 2013, 2:50 am
@TinyMtn Awesomeness....
January 14, 2013, 3:11 pm
@duann Thanks! TinyMtn loves photos, too. I've got a 200mm Mt. Rainier (among others) in the mail right now. Pics or it didn't happen!
January 14, 2013, 2:16 pm
This is a cool concept, I am looking forward to seeing some photos of the 3D prints.
January 14, 2013, 12:39 pm
 
  • White Strong & Flexible

    White nylon plastic with a matte finish and slight grainy feel.

    $199.00

Favorited by