Mecha Ring (size 15ish in metal)

Mecha Ring (size 15ish in metal) 3d printed Jewelry Gift Guide Mecha Ring in Steel
Mecha Ring in Steel
Mecha Ring (size 15ish in metal) 3d printed Jewelry Gift Guide Steel, on my Finger
Mecha Ring (size 15ish in metal) 3d printed Jewelry Gift Guide Steel, on my Finger
Steel, on my Finger
Mecha Ring (size 15ish in metal) 3d printed Jewelry Gift Guide This is the Silver version, on my hand.
Mecha Ring (size 15ish in metal) 3d printed Jewelry Gift Guide This is the Silver version, on my hand.
This is the Silver version, on my hand.
3d Model Viewer
Mecha Ring (size 15ish in metal) 3d printed Jewelry Gift Guide
Mecha Ring (size 15ish in metal) 3d printed Jewelry Gift Guide
Mecha Ring (size 15ish in metal) 3d printed Jewelry Gift Guide This is the Silver version.
Mecha Ring (size 15ish in metal) 3d printed Jewelry Gift Guide This is the Silver version.
This is the Silver version.
Mecha Ring (size 15ish in metal) 3d printed Jewelry Gift Guide Mecha Ring in Steel
Mecha Ring (size 15ish in metal) 3d printed Jewelry Gift Guide Mecha Ring in Steel
Mecha Ring in Steel
This ring is about Men's Ring Size 15+, after metal shrinkage. It fits the largest finger on my rather large hands without a problem.

(UPDATE: I've made some changes that should get around that printing error Shapeways is now giving. I'll test it as soon as I have the money to buy new prints)
Tags:
Jewelry, Rings
cm: 2.834 w x 0.956 d x 2.858 h
in: 1.116 w x 0.376 d x 1.125 h

Comments

 
@MaxSMoke777 Max, it would be awesome if you could upload the pair of rings for me. I would really appreciate it, thanks!
February 6, 2013, 4:35 am
I love the ring, but when you say it's 15+ size, do you mean "USA size" as in http://www.onlineconversion.com/ring_size.htm? A 15+ size isn't even listed there...
January 20, 2013, 3:34 am
@MaxSMoke777 I was planning to have them in gold plate, but that is plated steel so it still will shrink, yes? The final initial diameters should be about 0.84 and 0.72. I unfortunately cannot afford two silver prints even though I think they look amazing in silver (unless if the two models are together it's only $50-60)
January 6, 2013, 9:41 pm
@Iggyfigs I have a smaller version available, but when printed in Steel, some of the parts get very fragile and might not survive the "Green" state of the Steel production. Steel prints formed from metal power, coated in a bit of plastic, and then they use lasers to melt the plastic to hold the metal powder together. This "Green" print is then fired in a Kiln until the metal binds together, and the plastic is vaporized. So I can make a smaller version, but it's possible bits might not come through. If you want to take that chance, send me a measurement of the interior diameter, in millimeters, of rings that fit you best. I suggest using calipers. Ring size charts can vary from county to country, region to region, sex to sex, so they ain't always very helpful. There's 3% to 5% shrinkage in Steel prints (from the plastic burn off), so if you want Steel, I'll have to figure that in as well.
January 6, 2013, 8:00 pm
Hey Max, is it possible you could make the Mecha Ring in size 12 and 8?
January 6, 2013, 7:34 pm
Great design, I like it .
December 28, 2009, 1:16 pm
 
  • White Strong & Flexible

    White nylon plastic with a matte finish and slight grainy feel.

    $4.72

Favorited by