GLaDOS Ring (White "Half" of Ring)

by Ammnra
GLaDOS Ring (White "Half" of Ring) 3d printed Jewelry Rings READ BELOW
Choose Material
  • White

    White nylon plastic polished to reveal a smooth matte finish.

Buy Now
Two Part Ring based on Portal 2 GLaDOS.


NOTE: This is just the white "face" part of the ring.
You must also order ”GLaDOS Ring (Black "Half" of Ring)” to have all the parts to make the ring.

The two part version comes 90% colored.
(You still need to paint the yellow and red eye dots on the black part)
The two parts just snap together. You can lock the 3 parts together with some super glue.

Available in US Sizes 6-12 (in Half Sizes)
Click for Size 6 White
Click for Size 6 Black

Click for Size 6.5 White
Click for Size 6.5 Black

Click for Size 7 White
Click for Size 7 Black

Click for Size 7.5 White
Click for Size 7.5 Black

Click for Size 8 White
Click for Size 8 Black

Click for Size 8.5 White
Click for Size 8.5 Black

Click for Size 9 White
Click for Size 9 Black

Click for Size 9.5 White
Click for Size 9.5 Black

Click for Size 10 White
Click for Size 10 Black

Click for Size 10.5 White
Click for Size 10.5 Black

Click for Size 11 White
Click for Size 11 Black

Click for Size 11.5 White
Click for Size 11.5 Black

Click for Size 12 White
Click for Size 12 Black

Click for US Sizes/Inner Dia

ATTENTION:The rings in the video/pics have been detail painted. The Shapeways parts will NOT be.
Each part will be one solid color.
Click for quick and easy detail painting guide

Thanks for your order and commitment to nerd culture!


IN: 0.389 w x 0.893 d x 0.558 h
CM: 0.988 w x 2.268 d x 1.418 h


Sign In or Join to comment.
Included this (and all your other Portal-themed rings) in an article for Coin Arcade about 3D-printed Portal items. Great work.
March 25, 2013, 9:57 pm
white and black parts DO NOT snap together well at all. the white part it too small and i'm going to have to sand it to make it fit.
September 5, 2012, 7:37 pm
So my ring(both parts) just showed up about 4 days ago. First impressions: Underwhelmed. When i first saw the 3 little parts I kinda felt like it wasn't as good as the pictures suggest and I was a little bummed out. The white and black parts snapped together fine, I didn't need any glue to hold them together, and I am not afraid of them coming apart at all. However, there is a second black piece that snaps on over the white one, and that part did not fit at all on mine. I assumed it just needed glueing, but rather than fitting snuggly the sides that overhang(and thus make it hold on so tightly) didnt even touch the sides of the white part. None the less I glued it on with some strong model glue and then painted the two small dots(yellow and red) onto the ring. it looked much better! I was happy with it, although I still felt it didn't live up to the picture. I wore it around the house for a few hours and the size was PERFECT.....but then I looked down and noticed the black part that didn't quite fit was gone, the glue had pulled a little dent of the ring out, not noticeable unless you are inspecting it, but now I feel I have an unfinished ring because that didn't hold on at all on its own. A few other things I noticed: I got mine in a size 6.5, and I feel like it looks a little distorted from being so small. For instance, I can't read the "glados" on the inside of the ring. And while in the picture it looks like you can see just where to put the dots...I kinda just guessed, and the red dot is hanging off the side a litttttttle because there wasn't much room to put them in there. Big fingers should be fine, but mine ar boney. The materials are...strange. I did not get the parts polished, as I was unsure which ones would look the best. GET POLISHED, I think it would look better. I wish the person selling them would tell you which ones look the best, the guess work was really annoying. But from what I understand "polished" looks just like plastic. Whereas mine is mate and feels porous. OVERALL: I like it, it looks nice. Make sure you SUPERGLUE on the tiny black part, and if you can get it in polished. Even without the tiny black part it looks like glados and it makes me smile, I wear it everywhere and if you didnt know what it was it just looks like a simple pretty ring, not too loud or attention grabbing, just right! :) PS: you should sell replacement black parts without having to get the whole thing :P
May 5, 2012, 2:17 am
The two parts don't fit together at all, and the smaller black part is completely worthless because it doesn't snap on in any way like the picture suggests. Plus, for some reason, the ring I got doesn't even fit me. Total waste.
April 25, 2012, 6:45 pm
i don't suppose you'd be willing to make this and the other half of it available for sale, i love the design but lack the skills to create it.
October 1, 2011, 1:24 pm
As a fellow shop owner who does multi-part models, may I recommend including a link to the other half in the description?
September 29, 2011, 10:13 pm
Don't forget the companion cube dice ;)
September 27, 2011, 9:11 pm


We're sorry to inform you that we no longer support this browser and can't confirm that everything will work as expected. For the best Shapeways experience, please use one of the following browsers:

Click anywhere outside this window to continue.