GPS Holder BASE (U Blox M6) v1.3

GPS Holder BASE (U Blox M6) v1.3 3d printed Mechanical parts Maker/DIY Add a caption...
Add a caption...
GPS Holder BASE (U Blox M6) v1.3 3d printed Mechanical parts Maker/DIY Add a caption...
GPS Holder BASE (U Blox M6) v1.3 3d printed Mechanical parts Maker/DIY Add a caption...
Add a caption...
GPS Holder BASE (U Blox M6) v1.3 3d printed Mechanical parts Maker/DIY Add a caption...
GPS Holder BASE (U Blox M6) v1.3 3d printed Mechanical parts Maker/DIY Add a caption...
Add a caption...
3d Model Viewer
GPS Holder BASE (U Blox M6) v1.3 3d printed Mechanical parts Maker/DIY
GPS Holder BASE (U Blox M6) v1.3 3d printed Mechanical parts Maker/DIY
GPS Holder BASE (U Blox M6) v1.3 3d printed Mechanical parts Maker/DIY Add a caption...
GPS Holder BASE (U Blox M6) v1.3 3d printed Mechanical parts Maker/DIY Add a caption...
Add a caption...
GPS Holder BASE (U Blox M6) v1.3 3d printed Mechanical parts Maker/DIY Add a caption...
GPS Holder BASE (U Blox M6) v1.3 3d printed Mechanical parts Maker/DIY Add a caption...
Add a caption...
GPS Holder BASE (U Blox M6) v1.3 3d printed Mechanical parts Maker/DIY
GPS Holder BASE (U Blox M6) v1.3 3d printed Mechanical parts Maker/DIY
This is the base for the U-Blox GPS from Ready to Fly Quads. It's designed to screw to the top of the multi wii case or to a 45mm pattern. I've added 4x mounting points 45mm apart to allow for mounting the U Bloc GPS unit directly above the Multi Wii 2.0 Pro (Ready to Fly Quads) Hard case.

ublox 6m GPS No Mounting Backplane: http://witespyquad.gostorego.com/flight-controllers/ublox-6m-gps-module-no-mounting-backplane.html

There is a v2 of this GPS that hasn't been tested yet.

(NOTE: 1: When running the wire for the GPS, do not attempt to tuck it under the plug. It will not fit, instead run the wire around the board and make it go under a joining side. 2: You'll notice the the GPS mounts more to one side, make sure the plug is on the side that gives you the most room.)

Making final modifications.

I'm not affiliated nore do I work for ready to fly quads. I'm just a huge fan of their products and I'm desinging parts to make my quad look cooler and more finished while protecting my eletronics. http://witespyquad.gostorego.com/

VERSION DESCRIPTION
v1.1 - Design complete, reviewing for modifcation.
v1.2 - Model passes print constraints, and has been printed.
v1.3 - First 3D print has been inspected for quality, fit, and function.
v1.4 - Item tested and modifications made if needed.
v1.5 - It has been printed, tested, and adjustments has been made. Items meets design intent and function when printed with default material.
v1.6 and up - modifications to enhance function or additions to design.
cm: 5.3 w x 5.3 d x 1.906 h
in: 2.087 w x 2.087 d x 0.75 h

Comments

 
I Changed the design slightly, Now the lid has a lip that will fit over the base with 4 areas where it will snap in place (instead of the posts) and be held. This will be more secure and give it fewer points of failure in the event of a sever crash. One the base the only change is that the posts to mount the lid in place are now gone.
February 17, 2014, 5:05 pm
 
  • White Strong & Flexible Polished

    White nylon plastic polished to reveal a smooth matte finish.

    $10.32