DJI Phantom Custom FPV Undertray -Fatshark (d3wey)

DJI Phantom Custom FPV Undertray -Fatshark (d3wey) 3d printed Accessories Gadgets
DJI Phantom Custom FPV Undertray -Fatshark (d3wey) 3d printed Accessories Gadgets
DJI Phantom Custom FPV Undertray -Fatshark (d3wey) 3d printed Accessories Gadgets
Digital Preview

Not a Photo

DJI Phantom Custom FPV Undertray -Fatshark (d3wey) 3d printed Accessories Gadgets FPV Undertray shown in flight
DJI Phantom Custom FPV Undertray -Fatshark (d3wey) 3d printed Accessories Gadgets FPV Undertray shown in flight
Digital Preview

Not a Photo

DJI Phantom Custom FPV Undertray -Fatshark (d3wey) 3d printed Accessories Gadgets FPV Undertray shown in flight
DJI Phantom Custom FPV Undertray -Fatshark (d3wey) 3d printed Accessories Gadgets FPV Undertray shown in flight
Digital Preview

Not a Photo

DJI Phantom Custom FPV Undertray -Fatshark (d3wey) 3d printed Accessories Gadgets Shown with d3wey battery cage, filter housing and "Frame'ish" around the GoPro. This is a dual battery setup
DJI Phantom Custom FPV Undertray -Fatshark (d3wey) 3d printed Accessories Gadgets Shown with d3wey battery cage, filter housing and "Frame'ish" around the GoPro. This is a dual battery setup
Digital Preview

Not a Photo

DJI Phantom Custom FPV Undertray -Fatshark (d3wey) 3d printed Accessories Gadgets 4 x Male to Female 25mm Hex Spacers are used to fix it in place (not supplied)
DJI Phantom Custom FPV Undertray -Fatshark (d3wey) 3d printed Accessories Gadgets 4 x Male to Female 25mm Hex Spacers are used to fix it in place (not supplied)
Digital Preview

Not a Photo

DJI Phantom Custom FPV Undertray -Fatshark (d3wey) 3d printed Accessories Gadgets Spacers replace the inner screw on each leg
DJI Phantom Custom FPV Undertray -Fatshark (d3wey) 3d printed Accessories Gadgets Spacers replace the inner screw on each leg
Digital Preview

Not a Photo

DJI Phantom Custom FPV Undertray -Fatshark (d3wey) 3d printed Accessories Gadgets
DJI Phantom Custom FPV Undertray -Fatshark (d3wey) 3d printed Accessories Gadgets
Digital Preview

Not a Photo

DJI Phantom Custom FPV Undertray -Fatshark (d3wey) 3d printed Accessories Gadgets The original screw can then be used to secure the tray
DJI Phantom Custom FPV Undertray -Fatshark (d3wey) 3d printed Accessories Gadgets The original screw can then be used to secure the tray
Digital Preview

Not a Photo

DJI Phantom Custom FPV Undertray -Fatshark (d3wey) 3d printed Accessories Gadgets Shown here wit the d3wey Fatshark Filter Housing attached
DJI Phantom Custom FPV Undertray -Fatshark (d3wey) 3d printed Accessories Gadgets Shown here wit the d3wey Fatshark Filter Housing attached
Digital Preview

Not a Photo

DJI Phantom Custom FPV Undertray -Fatshark (d3wey) 3d printed Accessories Gadgets Up and Under cable tidy keeps cables neat
DJI Phantom Custom FPV Undertray -Fatshark (d3wey) 3d printed Accessories Gadgets Up and Under cable tidy keeps cables neat
Digital Preview

Not a Photo

DJI Phantom Custom FPV Undertray -Fatshark (d3wey) 3d printed Accessories Gadgets Door is used to stop the TX from coming out
DJI Phantom Custom FPV Undertray -Fatshark (d3wey) 3d printed Accessories Gadgets Door is used to stop the TX from coming out
Digital Preview

Not a Photo

DJI Phantom Custom FPV Undertray -Fatshark (d3wey) 3d printed Accessories Gadgets TX Holder fully integrated (cannot be removed)
DJI Phantom Custom FPV Undertray -Fatshark (d3wey) 3d printed Accessories Gadgets TX Holder fully integrated (cannot be removed)
Digital Preview

Not a Photo

DJI Phantom Custom FPV Undertray -Fatshark (d3wey) 3d printed Accessories Gadgets Support struts and backbone keep it strong but light
DJI Phantom Custom FPV Undertray -Fatshark (d3wey) 3d printed Accessories Gadgets Support struts and backbone keep it strong but light
Digital Preview

Not a Photo

DJI Phantom Custom FPV Undertray -Fatshark (d3wey) 3d printed Accessories Gadgets TX slides in
DJI Phantom Custom FPV Undertray -Fatshark (d3wey) 3d printed Accessories Gadgets TX slides in
Digital Preview

Not a Photo

DJI Phantom Custom FPV Undertray -Fatshark (d3wey) 3d printed Accessories Gadgets Door fitted
DJI Phantom Custom FPV Undertray -Fatshark (d3wey) 3d printed Accessories Gadgets Door fitted
Digital Preview

Not a Photo

DJI Phantom Custom FPV Undertray -Fatshark (d3wey) 3d printed Accessories Gadgets Cables are routed through the back
DJI Phantom Custom FPV Undertray -Fatshark (d3wey) 3d printed Accessories Gadgets Cables are routed through the back
Digital Preview

Not a Photo

DJI Phantom Custom FPV Undertray -Fatshark (d3wey) 3d printed Accessories Gadgets The structure is thick and tough despite being very light (22 grams)
DJI Phantom Custom FPV Undertray -Fatshark (d3wey) 3d printed Accessories Gadgets The structure is thick and tough despite being very light (22 grams)
Digital Preview

Not a Photo

DJI Phantom Custom FPV Undertray -Fatshark (d3wey) 3d printed Accessories Gadgets Overview - this side will not be visible when fitted
DJI Phantom Custom FPV Undertray -Fatshark (d3wey) 3d printed Accessories Gadgets Overview - this side will not be visible when fitted
Digital Preview

Not a Photo

DJI Phantom Custom FPV Undertray -Fatshark (d3wey) 3d printed Accessories Gadgets
DJI Phantom Custom FPV Undertray -Fatshark (d3wey) 3d printed Accessories Gadgets
Digital Preview

Not a Photo

3d Model Viewer

About this Product

This is the d3wey Custom FPV Undertray for the DJI Phantom. It is designed around the Fatshark Predator V2 kit but can be used for other kits (please check measurements).

The tray is fitted to the Phantom via "4 x M3 25mm Brass Hex Spacers" (not included). They can be sourced from Ebay for about £2 - £3.

The spacers replace the inner screw on each of the Phantom's landing legs. The tray then sits on the spacers and the original M3 leg screws are used to attach the tray to the spacers.

The TX slides into the custom slot and is fixed in place with the supplied door which can either be sealed with small nuts/bolts (not supplied) or string/wire.

The internal dimensions of the TX holder are:

  • Width: 27mm
  • Height: 13mm
  • Depth: 56mm

This listing is for the Undertray only... the photo also shows the GoPro 'Framish' and Fatshark Filter Housing mounted - both available in the shop

*** - Please Note - *** As with any Shapeways product please be aware of what you are buying. This is a custom designed part not mass produced. It has a slighty rough finish (but nothing that will scratch items). I make every effort to test all my designs but I regret manufacturers do change their products from time to time. If in doubt please contact me.

- d3wey -


Dimensions

IN: 6.732 w x 4.134 d x 0.748 h
CM: 17.1 w x 10.5 d x 1.9 h
Sign In or Join to comment.
 
@Nathanita - Yep the 250mw that comes with the Teleporter kit is the same as the Predator so that will fit the TX holder. If you are using an anti vibration mount you would probably have to trim this but the material is easy to cut. Maybe better to look at the Zenmuse version which has a cut out already (depends on the shape).
January 11, 2014, 6:06 pm
Any idea if the cage will hold the Fatshark Teleporter V3 transmitter? Does the tray need to be modified if using an anti vibration mount?
January 11, 2014, 11:48 am
After minor modifications to fit Immersion 600mW FPV Transmitter
December 17, 2013, 9:25 pm
After minor modifications to fit Immersion 600mW FPV Transmitter
December 17, 2013, 9:24 pm
Unboxing of this item + stock battery cage
December 17, 2013, 9:23 pm
Unboxing of this item + stock battery cage
December 17, 2013, 9:22 pm
Unboxing of this item + stock battery cage
December 17, 2013, 9:21 pm
Unboxing of this item + stock battery cage
December 17, 2013, 9:21 pm
Unboxing of this item + stock battery cage
December 17, 2013, 9:20 pm
Unboxing of this item + stock battery cage
December 17, 2013, 9:20 pm
@Marsj027 Hi there - No currently it is designed around the stock setup, not a gimbal. Others have purchased the kit and modded it (with a dremel/craft knife) to fit in a variety of ways but as yet i've not seen anyone using it with a Zenmuse.
September 2, 2013, 9:44 am
Does this kit fit with DJI Zenmuse H3-2D?
September 2, 2013, 9:31 am
Do you have a photo of how your holding the transmitter in place. By this photo it looks like you have a few screws going into the holes but mine didn't come with a piece for those screws to hold the TX in place.
August 19, 2013, 10:06 pm
@techindahaus Yep this version of the tray has the transmitter tray built into it (i cannot be removed). If you scroll to the left through the pictures you will see a digital image of the actual design that is printed. I have other versions of the tray that don't have the transmitter tray built in but you would need to buy it and the TX holder seperatley. Maybe best to Privat Message me with what you are intending to do with your setup and I can advise what combo might be best.
August 8, 2013, 10:28 pm
Also, what if I want to mount an OSD setup? Is there room for that?
August 8, 2013, 10:27 pm
@d3wey Thanks. So just to be clear, the tray only includes the Fat Shark transmitter tray. Or I could just basically buy each componant seperatley at no real extra charge.
August 8, 2013, 10:06 pm
@techindahaus Hi there - The photo shows the undertray with the filter housing and the GoPro housing fitted so you can see how it would work if you buy all of the parts. This listing is just the undertray itself. Sorry for the confusion. I will update this listing to make sure that is noted. You 'could' squeeze two batteries in the gap on the tray but it will be quite a squeeze and if you still need it, you will have to mount the filter housing elsewhere via velcro. I designed the undertray with the intention to take one battery (in the battery cage) on the underside with another inside the phantom itself. This is how I fly it with dual battery mode. If you did squeeze two batteries on the underside (leaving the inside of the phantom free), you would need to be aware that the camera won't be able to tilt down very far as the batts will get in the way. Hope that is of help.
August 8, 2013, 9:43 pm
This design appears to also include the Fat Shark filter housing and GoPro housing. Is that correct? Also, can you then install two LIPO batteries in the gap?
August 8, 2013, 9:10 pm
@d3wey Hello i'm french.
August 5, 2013, 3:42 pm
@Doubidou Hi There - I can help find some if it helps... what country are you from?
August 5, 2013, 2:54 pm
@tctx3 hi you have a place to buy the brass spacers ? thxxx
August 4, 2013, 3:24 pm
Top quality product have fitted it and works great keeps it all neat and tidy very happy, bought the brass spacers off ebay if anybody is looking for them to use with this system. !!
July 23, 2013, 6:53 pm
 
  • White Strong & Flexible

    White nylon plastic with a matte finish and slight grainy feel.

    $37.63
Buy Now
Logo

Hello.

We're sorry to inform you that we no longer support this browser and can't confirm that everything will work as expected. For the best Shapeways experience, please use one of the following browsers:

Click anywhere outside this window to continue.