Discover » Miniatures
by
fakebusker83
Version 1.5
A 5-pack of the hungriest pestilence found in the universe! Each scrapacius has a hinged jaw and ball-jointed neck joint. The legs are designed to grab onto 3mm diameter rods. Enjoys cuddling.
Each Scrapacius stands about 2cm tall.
This design is successfully tested in FUD and WSF. FUD is recommended to capture all the fine detail.
TFW2005 Radicon thread here.
A 5-pack of the hungriest pestilence found in the universe! Each scrapacius has a hinged jaw and ball-jointed neck joint. The legs are designed to grab onto 3mm diameter rods. Enjoys cuddling.
Each Scrapacius stands about 2cm tall.
This design is successfully tested in FUD and WSF. FUD is recommended to capture all the fine detail.
TFW2005 Radicon thread here.
by
kampfflieger
1/144 Airco DH.2 British WWI fighter.
The D.H.2 biplane was Geoffrey de Havilland's second design for the Aircraft Manufacturing Company. This highly successful pusher had good maneuverability with an excellent rate of climb. Mounting the engine to the rear of the fuselage permitted the use of a fixed, forward-firing machine gun before the advent of the synchronous machine gun. Superior to the Fokker E.III, the D.H.2 helped end the "Fokker Scourge." Well past its prime and almost two years after its introduction, some squadrons of the Royal Flying Corps were still equipped with D.H.2s.
The D.H.2 biplane was Geoffrey de Havilland's second design for the Aircraft Manufacturing Company. This highly successful pusher had good maneuverability with an excellent rate of climb. Mounting the engine to the rear of the fuselage permitted the use of a fixed, forward-firing machine gun before the advent of the synchronous machine gun. Superior to the Fokker E.III, the D.H.2 helped end the "Fokker Scourge." Well past its prime and almost two years after its introduction, some squadrons of the Royal Flying Corps were still equipped with D.H.2s.
Perfect for the wargamers and collectors.
by
bondp99
1/7000 scale heavy cruiser. Reliable cruiser to fight the Bork and the Domino.
by
Drawn-SteelHero
Detailed sniper assault rifle with flip-down bipod converts into a 56mm robot action figure with 9 points of articulation.
Gun mode comes with a choice of three handles, any one of which can be fit onto the figure during assembly (and since they are attached via a simple clip-in hinge, you can keep the others handy and swap them later if you choose). Option 1 is a standard 5mm post, which is compatible with any figure bearing a 5mm peg hole. Options 2 and 3 are modified versions of the post, which can still be used by figures with 5mm peg holes, but also have built-in clips which allow them to clip onto any 3mm diameter rail. One version has the opening of the clip positioned parallel to the length of the gun, the other perpendicular.
Supplied as a 18-piece kit. Finishing (painting/dyeing) required, alternatively can be purchased in one of the available pre-dyed colours .
Assembly and conversion instructions available HERE.
Gun mode comes with a choice of three handles, any one of which can be fit onto the figure during assembly (and since they are attached via a simple clip-in hinge, you can keep the others handy and swap them later if you choose). Option 1 is a standard 5mm post, which is compatible with any figure bearing a 5mm peg hole. Options 2 and 3 are modified versions of the post, which can still be used by figures with 5mm peg holes, but also have built-in clips which allow them to clip onto any 3mm diameter rail. One version has the opening of the clip positioned parallel to the length of the gun, the other perpendicular.
Supplied as a 18-piece kit. Finishing (painting/dyeing) required, alternatively can be purchased in one of the available pre-dyed colours .
Assembly and conversion instructions available HERE.
by
kampfflieger
1/144 Albatros D.II German WWI fighter.
The Albatros D.II was a modified version of the Albatros D.I. Pilots complained that the D.I offered poor visibility from the cockpit. To solve this problem, the D.IIs upper wing was brought closer to the fuselage. Mounted to the fuselage in front of the pilot, the D.IIs twin, synchronous machine guns set the standard for other German and Allied fighters. By the end of 1916, increased production of the Albatros gave Germany numerical superiority in the air war.
Perfect for the wargamers and collectors.
The Albatros D.II was a modified version of the Albatros D.I. Pilots complained that the D.I offered poor visibility from the cockpit. To solve this problem, the D.IIs upper wing was brought closer to the fuselage. Mounted to the fuselage in front of the pilot, the D.IIs twin, synchronous machine guns set the standard for other German and Allied fighters. By the end of 1916, increased production of the Albatros gave Germany numerical superiority in the air war.
Perfect for the wargamers and collectors.
by
Chaffmar
A custom designed electric guitar perfect for Lego minifigs. (Does not actually make sound)
Recommended Materials:
White Detail OR
Strong and Flexible
Recommended Materials:
White Detail OR
Strong and Flexible
by
Calistotash
Meet Chrysalis, Queen of the Changelings. She wants your love...so what are you waiting for?
by
Drawn-SteelHero
Fearsome-looking machine gun converts into a 56mm robot action figure with 10 points of articulation.
Gun mode's handle is a 5mm diameter peg, making it compatible with many larger robot action figures.
Supplied as a 14-piece kit. Finishing (painting/dyeing) required, alternatively can be purchased in one of the available pre-dyed colours.
Assembly instructions available at:
http://www.shapeways.com/forum/index.php?t=msg&goto=21214&#msg_21214
If you purchase Salvo, in any material, I'd love to see your results in the "It Arrived" forum!
Gun mode's handle is a 5mm diameter peg, making it compatible with many larger robot action figures.
Supplied as a 14-piece kit. Finishing (painting/dyeing) required, alternatively can be purchased in one of the available pre-dyed colours.
Assembly instructions available at:
http://www.shapeways.com/forum/index.php?t=msg&goto=21214&#msg_21214
If you purchase Salvo, in any material, I'd love to see your results in the "It Arrived" forum!
