This is the worlds first cable guide to fit 4 cables and. This means that you can now mount the cables for your derailleurs, your rear brake, and your dropper post onto your frames cable guide mounts to give a clean looks to your bike and do away with those zip ties. This version accommodates 2 standard size gear cable outers, 2 standard size hydraulic hoses (brake hose and a Rock Shox Reverb hose). You can also fit a standard size cable brake cable into one of the hose slots. These are still undergoing testing so please send feedback as to what you thought of them and if any improvements can be made.

BE SURE TO CLICK THROUGH ALL PHOTOS USING THE ARROW BUTTONS TO SEE A/B SHOTS WITH AND WITHOUT THIS LENS. There are 8 total photos, but only 5 show at a time in the image bar. The four watch and microchip pictures are "with lens" and "without lens" iPhone 5 shots.

Make your own macro lens adapter for the iPhone 5. I designed the original version of this for my iPhone 4 (see "iPhone 4 Macro Lens" on Shapeways) when I couldn't find the close-up image quality I wanted for less than $60. This is far cheaper than anything commercially sold and, in my opinion, has better image quality.

Print this model and then buy a glass lens for $4 from Surplus Shed (http://www.surplusshed.com/). Their part number is L4471. For some reason the search function on the Surplus Shed site won't search part numbers. To find L4471, use the "Lens Finder" on their home page. In "Lens Finder" type:

Lens Type: PCX, Plano Convex
Diameter: 12mm to 12mm
Focal length: 51mm to 51mm

That will get you to L4471

The lens fits in a recess in the Shapeways model and is held in place with a few tiny drops of Superglue. If you get any glue on the lens it can be cleaned off with nail polish remover or acetone. The lens is plano-convex (one side is flat). When inserted in the model, the flat side of the lens should face the phone.

Note that the lens fits pretty snugly into the opening. Try fitting the lens before applying any glue. Before gluing, with the lens holder laying face-down on a table, lay the lens in position, and then push it into the recess by pushing the lens with the eraser-end of a pencil. Again, do this first WITHOUT glue. Once you know the lens fits cleanly, push it back out and put two tiny drops of superglue on opposite edges of the opening. I use a toothpick to apply the glue because squeezing the superglue directly out of the tube risks putting on too much. Only *tiny* drops are necessary. Then push the lens back in the same way as in the test fit.

The example photos of the watch and microchip have not been cropped or altered in any way. Those 4 shots were loaded straight from the iPhone 5 (though Shapeways compresses them). It appears that although Apple improved many aspects of the camera on the iPhone 5, focus range did not get closer, so this lens helps just as much for macro shots as it's brother did for the iPhone 4/4S .

PLEASE NOTE: This model will not slide over iPhone 5 cases. It fits only on an uncovered iPhone 5.

Portal Axle for Losi Mini Rock Crawler. You will need Mod. 0.5 gears with  20T and 30T.(www.Conrad.com Nr: 231835-51 and Nr:231843-51).This Portal Axle will fit 1.9" Tamiya rims. (Inner diametre greater than 43mm).
You will also need 4mm solid rod, to make some new axle for the hex, for mountig the tire.=========================================================================
Portal Achsen für den Losi Mini Rock Crawler. Dieses Set enthält alle Kunststoffteile zum Bau von 4 Portalachsen.
Die Achsen sind so designed das 0° Ackermann Effekt auftritt. Daher lassen sich die Portale auch als BTA montieren. (Spurstange hinter der Achse, oder davor.)

Weiters werden noch folgende Teile benötigt:
16 Stück Kugellager 8x4x3,
Jeweils 4 Stück Zahnräder von www.Conrad.com Nr: 231835-51 und Nr:231843-51
4 Stück 4mm Welle, auf der dann auch die Felge befestigt werden muss. Zb mit Querstift und Sechskant-Mitnehmer.

This is designed to have a small 1/2" OD bearing inserted, and used as a heavy duty swivel on my spinning kite bols. The fishing swivels currently in use are not really designed for the workout my kites provide them.

Huey 1:6 Scale Seat Frame Deck Fixing Point - required for all seat legs, these are fitted to the bottom of the legs with an M2 washer and Self Tapper to allow the twist lock flange to operate, it is then locked in position with the "Ring Pin".

Designed for customisers, this set of four sockets can be built into small scale figures to turn them into limbs for your combiner 'bots. They clip securely onto the larger figures' male plugs with a satisfying 'click', and won't come off until you want them to.
Also included is a bonus flap for the jet figure, which allows you to plug minibots onto his chest while in his combined form.

Contents: Four combiner sockets, one replacement flap for jet figure. Jet figure not included - sorry.

I love my bike! It's based on an old racing cycle frame combined with a lot of nice and rare bicycle parts. I do not want it stolen, so I carry it every day, 100 steps down, 100 steps up. Sometimes living on the 4th floor is a real disadvantage.
Adding a carrying handle seems useful and in fact it is working very well!

This carrying handle works nice on old steel bike racing frames. The diameter of the down- and seat-tube is 29 mm (1.14 inch). Please message me if you need it for another frame size.

It comes without screws and bolt nuts! You need two 4 mm screws and bolt nuts. The screws should be 10-15 mm (0.39-0.59 inch) long.

Bugaboo denote Left and Right facing to the front (small wheels forward) of the stroller so this disk is for the side without the brake lever.

This is a little mount I made for my GoPro when I realized that there wasn't a simple way to have the GoPro mounted on a bar or pole, facing axially / parallel to / along the direction of the bar.

I wanted something small, sturdy, and reliable, but I also wanted it to be cheap and even possibly disposable in case you have to leave it behind. I'm pretty happy with the way it came out.

How it works:
1. Buy one of these mounts for a size close to the diameter of the bar/pole/rod that you're mounting it to. It doesn't have to be exact! If you want, you can wrap some tape around the bar to beef it up to the right size and add some friction, but I didn't find this to be necessary in most cases. As long as you're close, you should be good to go.
2. Use two zip-ties to mount it to the bar (that's what the little rectangular divots are for!). Make sure you crank down nice and tight on the zip ties so that it doesn't slide or rotate around the bar. A tip: use some releasable zip-ties if you don't want to have to use scissors / pliers / a knife to get your mount back.
3. Lastly, pop out a screw and nut from any of your other GoPro mounts, and put them on this one. Mount your GoPro, and get some awesome footage!

Notes:
-> This is the 2" size, but should work well for bars that are between 0.5" and 1.5" in diameter.
-> To make sure that this actually works for everyone, I've already ordered three for myself in three different materials: Alumide, Sandstone, and White Strong & Flexible. All three came out beautiful looking, but the alumide came undersized and didn't quite fit :( and the sandstone is too brittle for me to recommend. please stick to White Strong and Flexible for a reliable mount!
-> I don't intend to make money off of this. I'm charging a $1 mark-up on each just to recover the costs of the test-prints, but the whole point is just to provide some unique mounts for the GoPro community so that we can get some sweet footage more easily. Please comment with any videos that you use these in, I want to see them!

This is my version of the Master FTO originally designed by Timur. For a detailed writeup on the history of this puzzle and a full review visit the topic at twistypuzzles.com: http://twistypuzzles.com/forum/viewtopic.php?f=15&t=21983.

This puzzle is based on my Dino Skewb, but has an extra shell required to attach the corner pieces. It moves quite well and is entirely stable.

Buying this model will get you all the plastic parts required to build a Master FTO. You will need to provide your own screws and stickers to finish the puzzle. Alternatively, fully assembled and stickered puzzles are available from me for a small additional fee at tom@tomvanderzanden.nl.

Metric Set
Part # Size
26307 0.71mm
26309 0.89mm
26313 1.27mm
26315 1.5mm
26320 2.0mm
26325 2.5mm
26330 3.0mm
26340 4.0m

Imperial Set
Part # Size
26307 0.028"
26309 0.035"
26313 0.050"
26316 1/16"
26320 5/64"
26323 3/32"
26327 7/64"
26331 1/8"

Requires 3 #6x1/2" wood screws for mounting. Grey Robust material is suggested.

Gyrocam servo gear for Hitec HS-425BB servo

The part to fix the boards to the base - part of the quadcopter frame (under development)

Monopoly Game Piece, or other uses where a very small miniature is needed. This prints very nicely, and has a nice heft when printed in Stainless Steel, for such a small piece. You can view a video of it on YouTube here: http://www.youtube.com/watch?v=WsPGjgcAaUA

Big Chop is a twisty puzzle like Rubik's Cube. It was named by Bram Cohen. The object of the puzzle is tor scramble the 120 pieces and try to turn them back. Twisty puzzle fans will be horrified to learn about the mechanism. There is a steel ball inside and all pieces have magnets that hold them around the ball. There is also a pedestal to support the puzzle. A special tool is needed to turn the puzzle.

Watch the YouTube clip
Read at the Shapeways Forum
Read more at the Twisty Puzzles Forum

Please contact Oskar directly if you are interested in obtaining a fully colored, stickered and assembled sample of this puzzle.
(That is, with steel ball and magnets)

DJI Phantom Landing Gear Kit V3, includes the Leg Mounts, Compass Mount and 4 Leg Ends. Now with ever wider stance than earlier. These mounts fit directly to your Phantom, using the stock screws, and replace your stock landing gear. You provide your own 6mm tubing (preferably carbon fibre or aluminium), cut to the desired length, to give you the height you want, in order to allow for taller gimbals/camera set up/dampening mounts and so on. I have found 5" tube to be an ideal length for my set up, with gimbal and GoPro. Please note, that the tubing is not included in the listing, they are to show what the assembled kit looks like on the leg extensions. The kit includes 4 Leg Mounts, 1 Compass Mount and 4 Leg Ends.

The leg mounts are directional, and there is now a small marking under each leg, to easily identify (1-4 dimples refering to the arm number as in the manual). 1 = front left arm, 2 = rear Left arm, 3 = rear right arm, 4 = front right arm. This is when the Phantom is viewed from the front.

These are a beefed up version of the previous Leg Mounts I made, and use in the video, showing how I made the set up on my Phantom. Updated, so tubing can be pushed into the holes (which are slightly cones), and secured with a 3mm fixing screw (not included). The mounts are directional, like your props. see pictures above for reference or check out this video of how I assembled mine http://vimeo.com/simensays/phantom This is a simple DIY mod that replaces the stock landing gear, allowing you to easily make your Phantom taller, more stable, save weight (depending on how long you want your legs and what type of tubing you use) and a better overall look and stance. Only basic tools are needed. I am setting up a blog on my website, where I will post info, videos etc on other mods I have done to my quad, including how to make the leg extensions. www.simensays.com Beware to mount your Compass correctly, to maintain optimal flight characteristics on your Phantom. It should be mounted perpendicular to the body, in a vertical position. The included compass Mounts makes this very easy when using these legs. I use velcro on to fasten my compass.

Nomad Panohead Samyang 7.5mm MFT +0° OMD

Visit thomashuang.net for more information

A compact and lightweight panohead with portability in mind, the Nomad Panohead is quick and simple to use. It is designed to mount a Samyang 7.5mm MFT fisheye lens with a Sony NEX or Micro Four Thirds (MFT) camera for creating spherical panoramic photos in 4 shots. The Samyang lens is also branded by Rokinon, Walimex Pro, and Bower. The Nomad Panohead body and fasteners are sold and shipped separately, due to the production process. You need to purchase fasteners to operate the Nomad Panohead.

• Fixed tilt +0°
• Fixed position at NPP of horizon
• Rotator at 15° increments, indicators for 4 + 6 divisions
• Flip rotator over for smooth rotation
• Free access to focus + aperture rings
• Camera orientation in portrait or 37°, grip up or down
• Material: Polymide 12 Nylon, strong and durable
• 3/8"-16 thread mount (1/4"-20 adapter not included)
• 9000 x 4500 px resolution with 16mp APS-C camera
• 10,400 x 5200 px resolution with 12mp MFT camera

This purchase is for the panohead body ONLY. Fasteners are sold and shipped separately. You MUST purchase fasteners to operate the Nomad Panohead. Camera, lens mount adapter, lens, tripod, monopod, thread adapter, tape, knife, bags, and other accessories in photos and videos are not included and need to be purchased on your own.

Compatible with:

• Olympus OMD E-M5, E-P1, P2, P3, PL1, PL2, PL3, PM1
• Panasonic GX1, G3, GF1, GF2, GF3, GF5
• Panasonic G1, G2, GH1, GH2, GH3 (grip up only)
• Sony NEX-7, NEX-6, NEX-5R, NEX-5n, NEX-5, NEX-f3, NEX-c3, NEX-3

Ultra-Micro P-51D Mustang Cockpit Kit (1:28 scale) (Pilots sold separately)

This is a tiny cockpit kit for the micro Mustangs. It's appropriate size for Parkzone Ultra-Micro series P-51D Mustangs, or for any similar sized planes.

Total weight for the parts: 1,8 grams.

Note: Shapeways has minimum order sum of $25.00. You need to buy multiple items to cover the minimum amount. Check all the other options at my shop: www.shapeways.com/shops/palmen3d

All the prices include shipping and non-EU members get the models free of VAT.

Assembly Video

Arm Mount R
Arm Mount L

NOTE: This is a kit to build a toy replica inspired by the weapons from the Assassin's Creed Series and Dishonored . This kit is designed specifically as a con-safe cosplay prop. The end of the prop is squared-off and blunt and is therefore in no way intended to create a potentially dangerous weapon. Any modification to the design as sold is outside the recommendation and responsibility of the creator and manufacturer of this kit.

Chip for the Sleeve to increase accuracy of the square malice pommel.

Helicopter Casing Clip (Working) with Lock pin - suitable for all scale Models, this item is currently 1:6 scale

Hypotrochoid gear system part 1 of 2. In order for you to combine two colors in the gear system, it is split into two products. You can find part 2 of 2 here:
http://www.shapeways.com/model/151829/hypotrochoid_3_to_5_part_2_of_2.html?gid=ug26333