train wheel test upload - do not build, quote only

A replacement keyboard foot for the one I lost.

1 required for whole assembly This is the tip of the thumb of the bob

Lost one of the plastic feet from your Ikea Julius barstool? Replace it with this 3D print. Instructions: Force into metal foot of stool like you ...

SH06d Nerv Case for use with Incipio DualPro Silicon Sleeve

3rd version of the tilt-shift mechanism for Canon EOS. Tilt up to 10 degrees and shift up to 12 mm. A +10 diopter 58mm macro filter lens is neede...

A bobbin sized to fit Majacraft spinning wheels. This version is NOT FUNCTIONAL AS-IS: the holes at each end are about 0.1 mm too small and requir...

Case for "FEZ Cerbuino Bee"

1 required for whole assembly This is the middle, thumb bone on the bob

1 required for whole assembly This is the pinky-knuckle joint of the bob

1 required for whole assembly This is the half of the palm that supports the pinky and the 3rd finger of the bob

1 required for whole assembly This is the 'saddle joint' of the thumb that gets installed into the palm

1 required for whole assembly This is the first bone of the pinky, just off the pinky knuckle

UNTESTED: Gear for MXL Belt with 102 teeth, designed for a CCTV Prototype. 3mm mounting holes, 50mm hole in the middle.

1 required for whole assembly This is the bottom, thumb, long-bone just attached to the saddle joint

=====NOTE===== This design is still being worked on so it is not currently available for sale. Once I have tested that the rails fit and stay secur...

FOR AIRSOFT GBB ONLY. This is a custom slide for the KWA ATP. This is the first version. It currently has been tested and functions. It was pri...

DiaLFonZo produced the first prototype for his V-Tail copter frames in March 2012. This was one of two main size V-Tail frames he soon when on to p...

If your name is Patrick, or you have a Patrick in your life, this standing name plate is for you! This one has holes for 5mm LEDs and a channel fo...

This is an actual photo of a KJ66 Miniature Gas Turbine Engine. Stainless high strength Steel for high speed applications. Very finely toleranced, ...

Open Source Lens Motor Mk I Stepper motor based lens control motor, for use with eMotimo TB-3 or Dynamic Perception Mocobus boards. You need this t...

You need this to build the Open Lens Control Motor MkI. You also need the left shell.

4x 6-Tooth High Strength Sprocket

Centerplate to the HK KK2.0 LCD Board on HK Q450 Frame

Camera mount for the HobbyKing Q450 Glass Fiber Quadcopter Frame 450mm with Integrated PCB. Mount slides over one of the protrusions from the fram...

The original Rock Band guitars didn't have a ring around the Start button, making it very easy to accidentally halt game play by bumping the button...

DiaLFonZo produced the first prototype for his V-Tail copter frames in March 2012. This was one of two main size V-Tail frames he soon when on to p...

A set of Computer expansion slot cover plates free for you to download, modify, or have printed "commission free"

DiaLFonZo produced the first prototype for his V-Tail copter frames in March 2012. This was one of two main size V-Tail frames he soon when on to p...

0.95" tall foot for a 1.55"x0.95" inside dimension rectangular tubular leg. Inserts 0.45" in to the leg. Recessed "L" logo on one side.

This is a microscope ring light. Add 28 5 mm LEDs (Nichia NSPW500GS-K1 for example) and current regulators. I used LM317 based CC sources with 5-6 ...

1 Frame and 1 Pivot-Mount for GoPro Hero3, fits to "Herbert Richter" HR-4point-Mounts. Put a thin layer (1 to 2 mm) of foam rubber into the frame b...

The rear sight for my KWA ATP custom slide.