Pen not included. This sleeve is for Kickstarter backers of the Pen Type-A campaign. If you bought a USA made version of the pen at shop.cwandt.c...

The intrauterine device (IUD) is the world's most widely used method of reversible birth control for women. But as their production and common mate...

Downloadable 3D Printable Bumper for the iPhone 5. As per Apple's dimensions and we have checked the corners on the iPhone 5 against an existing ca...

This is a small sample of the "full color sandstone" material, for calibration purposes. It can be used to determine what the colors of your 3d pri...

Gyrocam servo gear for Hitec HS-425BB servo

Capacitor bracket for a capacitor 47mm in diameter. Has a bridge to allow wires to pass underneath. It has holes along the circular portion to al...

Downloadable 3D Printable Case for the iPhone 5. As per Apple's dimensions and we have checked the corners on the iPhone 5 against an existing case...

Gyrocam lens gear for Contour Roam camera

Custom pedal design. Should fit on a standard pedal skeleton. I've prototyped this on Sandstone but it should be made from metal. I'm including sa...

Part to be used as support for the light foam wheel. - part of the quadcopter frame (under development)

Part to build a KK2.0 board protection on a HK q450 frame, youll need 4 of them. With the part "mittelkreuz" or the part "mittelkreuz zu" it will f...

Gyrocam rail mount for Contour Roam camera

DiaLFonZo produced the first prototype for his V-Tail copter frames in March 2012. This was one of two main size V-Tail frames he soon when on to p...

Gear 36 teeth, pitch radius 18mm

This is meant to hold our pleats without drilling into the window frame. Not yet tested if it's strong enough.

Finally the official release of the SkyLight SBG Digital Brushless Gimbal for GoPro Hero 2 HD Cameras!! Designed for the AlexMos SImple Brushless ...

Audi Hazard Trim Latch by MatthewLaBerge

5-spoke 52mm RC Car rim

2-Blatt Prop-Halter für EPP1045. Propellerachsen haben einen Durchmesservon oben 5mm, unten 4mm, um noch ein M5 Gewinde reinschneiden zu k&...

3-Blatt Prop-Halter für EPP1045. Propellerachsen haben einen Durchmesservon oben 5mm, unten 4mm, um noch ein M5 Gewinde reinschneiden zu k&ou...

This is a mounting solution for attaching a Primesense Asus Xtion Pro or Asus Xtion Pro Live to a DSLR or other camera for hybrid depth sensor/HD v...

This part is a replacement firing pin for the delta-wing missile launcher in the Shogun Warriors Raydeen/Popy Brave Reideen Jumbo Machinder. The p...

Project Details: http://yzrandome.blogspot.com/2012/06/darker-than-black-heis-dagger-replica.html

A connection piece to be used between the oversize clamp and Busch & Müller Ixon Bicycle Headlights. It's modeled based on the original part, but ...

Part of a wire leg for a multirotor. Each leg needs two hinges. It is held to 1/2" (13mm) square arm with two zip ties. The hinge either holds the ...

This is a basic bezel to fit over the TimeSquared watch made by adafruit industries. The watch is excellent by itself, but the LED matrix that make...

This is a replacement part for the rewind drive of a Bauer P6 16mm film projektor. My projector had problems rewinding the film after viewing. It l...

2-Blatt Prop-Halter für EPP1045. Propellerachsen haben einen Durchmesservon oben 5mm, unten 4mm, um noch ein M5 Gewinde reinschneiden zu k&oum...

This is a Sheet Set for a Hollow Mini Mendel. Parts were made hollow to cut down on cost of printing. Just fill them with some sort of epoxy resin ...

Military tire for 1/24 scale truck.