by
MyClone
This part is a replacement firing pin for the delta-wing missile launcher in the Shogun Warriors Raydeen/Popy Brave Reideen Jumbo Machinder. The part was designed by Popy and reverse-engineered by Sanjeev Selvaraj of http://brownnoize.blogspot.com/ -- thanks Sanjeev!
by
Yangorang
Project Details: http://yzrandome.blogspot.com/2012/06/darker-than-black-heis-dagger-replica.html
by
thorwil
A connection piece to be used between the oversize clamp and Busch & Müller Ixon Bicycle Headlights. It's modeled based on the original part, but the top is put on in reverse. See http://thorwil.wordpress.com/2012/02/25/3d-printing-to-the-rescue/ for details
by
trearick
Part of a wire leg for a multirotor. Each leg needs two hinges. It is held to 1/2" (13mm) square arm with two zip ties. The hinge either holds the end of the wire leg or the wide end of the cross arm.
by
keitarusm
This is a basic bezel to fit over the TimeSquared watch made by adafruit industries. The watch is excellent by itself, but the LED matrix that makes up the face has very sharp edges.
by
sgust
This is a replacement part for the rewind drive of a Bauer P6 16mm film projektor. My projector had problems rewinding the film after viewing. It looks like the original part had shrunk with age, developed cracks und finally broke. The replacement works without problems so far.
by
tabraham
2-Blatt Prop-Halter für EPP1045. Propellerachsen haben einen Durchmesservon oben 5mm, unten 4mm, um noch ein M5 Gewinde reinschneiden zu können. Die Rotationsachse hat 4mm.
by
freakinhuge
This is a Sheet Set for a Hollow Mini Mendel. Parts were made hollow to cut down on cost of printing. Just fill them with some sort of epoxy resin to give them strength.
Pretty expensive alternative to printing them yourself on a DIY 3D printer, but time is money... right?
These are provided AT COST. No profit here, since they are GNU GPL...
Original single hollow parts done by Marcus Wolschon @ http://www.thingiverse.com/thing:2204
Single sheet hollow parts page on thingiverse @ http://www.thingiverse.com/thing:5074
Pretty expensive alternative to printing them yourself on a DIY 3D printer, but time is money... right?
These are provided AT COST. No profit here, since they are GNU GPL...
Original single hollow parts done by Marcus Wolschon @ http://www.thingiverse.com/thing:2204
Single sheet hollow parts page on thingiverse @ http://www.thingiverse.com/thing:5074
by
Oskar_van_Deventer
Proportional Mixup was suggested by Alex Polonsky. The puzzle is a shape-mod of the Mixup Cube. By having rhombicuboctahedron-shaped cubies, the cubies can be proportional like in a regular Rubik's Cube. However, this puzzle also has 45 degrees slice moves, resulting in some weird shapeshifting.
Watch the YouTube video.
Read at the Shapeways Forum.
Read more at the Twisty Puzzles Forum.
Please contact Oskar directly if you are interested in obtaining a fully colored, stickered and assembled sample of this puzzle.
Watch the YouTube video.
Read at the Shapeways Forum.
Read more at the Twisty Puzzles Forum.
Please contact Oskar directly if you are interested in obtaining a fully colored, stickered and assembled sample of this puzzle.
by
dhdecandia
4 required for whole assembly
This is the second bone, the middle, finger bone (not middle-finger bone), for all four fingers, including the pinky.
by
PLss
This functionally tested Polyamid (PA 2200, Nylon) Part is used as a ventilation grid cap for the air ventilation system of a Ford Focus limousine. This part is fully functional and can be printed in different colors. As a 3D printing material we recommend Shapeways "Strong and Flexible". With this material and the resulting tolerances, the spare part will best guarantee interchangability. CAUTION! This part is for the RIGHT SIDE. Please find the part for the left side also in our shop.
by
Kimo_Sullivan
Female reversing ring for 58mm photography lens filters.
Threads: 58mm x 0.75mm
Length: 8mm
Outer diameter: 62mm
by
dhdecandia
4 required for whole assembly
This is the tip of the fingers, not the thumb, of the bob
by
Ted
Replacement clip mount on the Verizon Droid1 case. This clip will fit into a $4 suction arm set from MPJA here: http://www.mpja.com/prodinfo.asp?number=18521+MI ... Easy mod for mounting your droid 1!
by
Varadero
Führungsstück Windschild Ducati Multistrada Modelljahr 2013.
Wird 2 mal benötigt. Zur Beseitigung bzw. Milderung der Klappergeräusche
die mit den Orginalteilen am Windschild auftreten.
by
tbmartin12
Table top Roller Coaster, there is 2 ways to print this model.
1. print entire assembly with body and wheels.
2. print body and wheels separately for more color options.
Wheel are designed to spin!
Recommend printing "white strong & flexible" for best price and "do it yourself" custom painting.
Custom engraving is available by request for free! Enjoy!
by
toddsampson
Ten (10) tooth XL belt pulley for use with stepper motors with a 5mm shaft. Great for driving x and y axis belts on a Prusa or other RepRap 3d printer.
This model prints 10-up to help keep the cost around $5/each.
by
cbertucio
If you own a Sony wireless bluetooth lapel microphone (models ECM-AW3 or ECMHW2) you can place the microphone unit into the top and cover it with a Foam Windscreen, and you now have a wireless handheld stick mic.
