this is the smallest i can make a wheel diameter wise that will fit the micro gear motors http://www.pololu.com/catalog/product/998 and it has the ...

Tube bracket to hold a 20mm (OD) tube in the Flexacopter. Holes are for m3 bolts. Plate distance is about 22mm after clamping the tube.

Module 0.5 Pressure angle: 25° Teeth: 10 Primitive diameter: 5mm Overall diameter: 6mm Teeth height: 4mm Bore diameter: 2mm

Want a gear on the top of a micro-servo? Here is what you want ! (Suggest to use Frosted Detail or Frosted Ultra Detail)

"Decepticon Logo" Software: 3Ds Max 2013, KeyShot 4 Pro. Hardware: Intel DX79SI, i7-3960X, 64GB RAM, GeForce GTX 690. See full work at: http://bit....

Motor mount for an automated Etch-a-Sketch

Rover ver 6.0, gear holder, Team Plan B, Googe Lunar XPRIZE. For rover (model) require -2 For ground station - 2 http://www.adobri.com/ProjectVe.aspx

Rover ver 6.0, antenna's gear holder, Team Plan B, Googe Lunar XPRIZE. For rover require -2 For ground station - 2 http://www.adobri.com/ProjectVe....

Rover ver 6.0, antenna's gear holder, Team Plan B, Googe Lunar XPRIZE. For rover (model) require -2 For ground station - 2 http://www.adobri.com/Pr...

Rover ver 6.0 / Ground station v 1.0, frame, Team Plan B, Googe Lunar XPRIZE. For rover (model) require -2 For ground station - 1 http://www.adobri...

Rover ver 6.0, part of the frame, Team Plan B, Googe Lunar XPRIZE. For rover (model) require -2 for ground station requare -2 http://www.adobri.co...

Arm Base component of the Serenade Project

1 required for whole assembly This is the index finger, or pointer finger, or 1st finger, knuckle-joint of the bob

***THIS MODEL IS UNTESTED, PURCHASE AT YOUR OWN RISK!*** A connector ramp for Metrotitan/Metroplex to allow him to connect with Micromaster bases....

This is a small bracket intended for attaching LED lights to a Quadcopter frame that uses square aluminum booms. It will hold two 5mm LEDs, one at ...

Team Plan B vehicle, wheel part

1 required for whole assembly This is the 'wrist' of the bob

I designed this wheel pod for use with a 40 mm diameter tire with a width of 15 mm or less. The axle hole is 1 mm to mark the bottom most point f...

1 required for whole assembly This is the tip of the thumb of the bob

A mount for attaching a C500 Series Logitech Web Camera to a RC servo.

This is a small bracket intended for attaching LED lights to a Quadcopter frame that uses square aluminum booms. It will hold two 5mm LEDs at a 45 ...

Arduino DFRobot LCD Shield - frame For panel mount -

1 required for whole assembly This is the middle, thumb bone on the bob

1 required for whole assembly This is the pinky-knuckle joint of the bob

1 required for whole assembly This is the half of the palm that supports the pinky and the 3rd finger of the bob

1 required for whole assembly This is the 'saddle joint' of the thumb that gets installed into the palm

1 required for whole assembly This is the first bone of the pinky, just off the pinky knuckle

prototype mechanism

1 required for whole assembly This is the bottom, thumb, long-bone just attached to the saddle joint

This is the cylinder part of a kind of sensor that is not so easy to find on the net, i just wanted to read my muscle status by their toughness var...

4x 6-Tooth High Strength Sprocket