This is the first update and the best solution for the first purchase! it is the most durable one and has two lids (with now 8 clipping balls) included ... also the holes for LED´s inside like on the 0.7mm version. for Boardsize V939, V202,H36,Ladybird 20x20mm hole distance battery up to 350mah Update 02 has holes for mounting the Hubsan board now! just cut them of, if not needed. Motors: 7x20mm Coreless (syma X1, hubsan, Ladybird.... thread: http://www.rcgroups.com/forums/showthread.php?t=1838771 Material alumide is not tested, but you can get this model in Colours!

This is the first Update in 0.7mm it has the two lids included. it has holes for 3mm LED´s inside and has a stronger lid closing cliping mechanism. it is about 3 grams less than the 1mm Microbody which is stronger of course.

This is a center piece for the six axes of a hexacopter. The axes are 10 x 10 mm, thickness 1mm.

80mm PC Fan Grill with custom text on it.

The alternative mount bottom part of the quadcopter frame (under development).

RANGE/SENSITIVITY ENHANCER FOR PING TYPE ULTRASONIC SENSOR

 

A low cost way to wring the maximum performance from your ultrasonic range finder without changing the set-up.

Improves the following performance characteristics:

• The over-all range of the unit  
• The directional properties of the unit (senses in the direction pointed)
• The sensitivity of the unit
  • Smaller targets can be detected
  • Better luck detecting  acoustically "soft" targets like cloth, stuffed animals, fur etc.

How to use:

• Simply slip the unit over the case of the transducer for instant improvements over no cone at all
• For a more permanent assembly a piece of tape to increase the friction fit or a dab of glue
• Use one on the receiving transducer for modest gain
• Use one on the transmitter and one on the receiver for maximum gain
• Mix and match with other shaped cones to tailor the gain and directional properties to match your application
   

 

*Warning!  The range can be increased to the point that detection of "old" ping signals results in erratic readings if range to target and speed of sound is not taken into account.

CO2 Car

Finally the official release of the SkyLight SBG Digital Brushless Gimbal for GoPro Hero 2 HD Cameras!! Designed for the AlexMos SImple Brushless Gimbal Control (SBGC) board, the SkyLight open source gimbal project offers full 360deg 2 axis stabilisation capable gimbal, specifically for the GoPro Hero 2 HD camera (Hero 3 coming soon!). cheap, light, strong, and fully balanced and ready to go "out of the box / off the printer"

This mounting bracket can be used to assembly and align the EMG 30 DC gearmotor. (also motors in diameter range from 25 – 33 mm)

The M4 threaded holes for set screws must itself be tapped. The set screws are M4 X 10 (2 X dog point, 1 X cone point)).

The mounting plates can be connected  with use of three M4 threaded rods.

The mounting plates are  designed for use during prototyping phase and not yet tested with external loads.

The center line of the DC motor mounted in a frame that consists of at least two mounting brackets and three threaded rods by means of two three set screws in any direction to make.

Allows mounting your flight controller board at a different angle than your power board or frame mounting holes.
3mm Holes at 45mm and 35mm to fit KK Multirotor, Multiwii (most) MultiWii Nano boards. Should fit any board with 45mm or 35mm hole to hole mounting size.
Note: Will not fit OpenPilot CopterControlor CC3D boards (32.5mm mounting hole to hole). See the other version in my shop for CC compatible board.

92mm PC Fan Grill with custom text on it.

Robots need caffeine too! This little surprise is hiding from the chaos of your desktop, simmering in his little world of mocha glee!

120mm PC Fan Grill.
Personalized version available at http://www.shapeways.com/model/170984/personalized_fan_grill_120mm.html

The feet part of the landing gear of the quadcopter frame (under development).

These are the herringbone pattern gears used in the Printrbot's extruder, designed by Brook Drumm (gears from Wade's Most Excellent Extruder). The gears that came in my Printrbot Plus kit were warped and misshapen. Laser-sintered nylon is a very precise way to make objects, why not my extruder gears? These are from the original STL files from the Printrbot.

See the picture with the black and the white gears:
The Black gear came with my Printrbot Plus kit. The STL file shows a diameter of 63.78 mm. The gear that was printed by a Printrbot in my kit measures 61.25 (averaged 8 measurements) The white gear was printed by Shapeways in Laser-sintered nylon and averages 63.25 mm

If you want a little Headhunter - Gothic - Cannibal - Biker vibe on your 3D Printer, check out the Skulltruder!

This is the second hardness sensor i made.
The two reasons that pushed me to do an HS2 is that the first one was too expensive, even if better, and it was too big. As the first version, this sensor has the capability of an internal wire connection, but, useless to say, you have to choose IR transmitter and receiver small enough.
You could use SFH 3100 F as photodiode and GL4800E0000F as emitter phototransistor.
The material should be plastic, as flexible as it could be. WSF could be ok, i'll now when it will arrive.

Rover ver 6.0, holder for bearing (inside each tube), Team Plan B, Googe Lunar XPRIZE. For rover (model) require -8 For ground station - 8 http://www.adobri.com/ProjectVe.aspx

This is a stock Losi Micro servo mount for custom chassis'. This will secure your servo to the chassis without the use of thick two-sided tape. This is the beta version and may or may not require slight modification's. Please comment or visit http://www.microtforum.com with feedback or question's or problem's with this part. Thanks Be sure to visit www.losimicroinfo.com for great information for the Losi micros.

Mechanical eyelid assembly for a 20mm eyeball.

Desktop stand for your Arduino Uno and Leonardo. High model. You can click on the board easy. The space underneath can be used to store a PC speaker. This stand is also usable to mount your Arduino Uno / Leonardo to a board or wall.

Fully functioning gear box.

When turning any gear will drive all other 5 gears. Transmission ratio is 1:1.