http://www.shapeways.com/forum/index.php Shapeways: Bring your creativity to life in 3D http://www.shapeways.com/forum/index.php?t=rview&goto=4566&th=979#msg_4566
So I have ben pondering filling the void inside the model with something to make it a solid mass:

(Theory: Drill a little hole in an inconspicuous spot, fill, and seal.)


I'm posting this to get some ideas from the masses as I am sure I am not the first to think about this.

Some ideas I've come up with are:

Epoxy:
Mixing enough of it could be a little pricey and I am not sure if there would be a chemical reaction with the model's medium. 5 minute epoxy would add some serious strength to the model.

Sand:
Ya, regular old sand. Where I live I have access to the ocean and a seemingly inexhaustable supply of sand. I like the idea of how much weight this would add to the model, but think it might be near impossible to fill all the void inside. Big con here is that the Sand does not add any strength to the model.

Plaster of Paris:
Major concern here is that I know POP can get pretty hot when it cures, so the melting point of the model's medium wold be a concern. Otherwise, a decent choice.

Wax:
I'm sure the melting point of wax is far lower than the Model's medium, but since heat is involved here, it bears consideration.

Resin:
Dozens of choices here, but all of them extremely sticky potential mess. Curing time would also be a concern.

Glue:
Chemical reactions with the Model's medium would be a concern with many types of glues. And the curing time might make others a bad solution. But I'm sure there is a glue out there that might fit the bill.


I'm looking for feedback, other ideas, advice, words of wisdom, experience, etc, etc.

anyone out there already done something like this?



]]> WiKKiDWidgets 2009-05-23T15:08:50-00:00 http://www.shapeways.com/forum/index.php?t=rview&goto=4568&th=979#msg_4568 daddymack 2009-05-23T20:49:51-00:00 http://www.shapeways.com/forum/index.php?t=rview&goto=4569&th=979#msg_4569
Also curious about the weight of the model afterward. I know thats relative to the size of the model, but give me a general idea.

Thanks for the reply Daddymack!]]> WiKKiDWidgets 2009-05-23T21:30:54-00:00 http://www.shapeways.com/forum/index.php?t=rview&goto=4571&th=979#msg_4571
I'm using polyurethane here as it's the least toxic and fairly sturdy. My supplier in Australia is here


http://www.barnesonline.com.au/productsByCategory.asp?intCat alogID=1&strCatalog_NAME=Resins+-+Polyurethane

I'm using easycast from that page. Anything of a similar spec will suit

It's the same resin I'm using in the casting process so it's sturdy enough to hold it's own... I've used it on pieces with bits as small as 2mm

Good luck;)]]> daddymack 2009-05-24T01:42:42-00:00 http://www.shapeways.com/forum/index.php?t=rview&goto=4581&th=979#msg_4581
I am going to research that and see if I can find myself a local distributor or a similar substance. That sounds perfect!

Much obliged Daddymack!
]]> WiKKiDWidgets 2009-05-24T05:26:26-00:00 http://www.shapeways.com/forum/index.php?t=rview&goto=4593&th=979#msg_4593 Ushanka 2009-05-24T21:27:26-00:00 http://www.shapeways.com/forum/index.php?t=rview&goto=4598&th=979#msg_4598
I fill the model with water first and measure the water to estimate how much resin to mix and pour. Make sure the model has been allowed to dry properly before resinating it though Resin and water are not friends...

Good luck]]> daddymack 2009-05-25T02:18:35-00:00 http://www.shapeways.com/forum/index.php?t=rview&goto=4610&th=979#msg_4610 On thing I would caution you against, is filling your model with something jelly like, or flexible (ie. silicon). I notice that things with a rigid exterior and a softer interior are apt to shell breakage, where they would not otherwise break when they are empty.

A long while ago, I ordered some half-fist sized models in the detail materials, whose "shells" were quite thin. Yet I purposefully left no exit hole, so it held the support material inside. The support material of the detail materials is sort of waxy and rubbery. All of the items were easy to "crack" in normal wear situations. One of them cracked during delivery.

-Whystler]]> Whystler 2009-05-25T14:52:40-00:00 http://www.shapeways.com/forum/index.php?t=rview&goto=60391&th=979#msg_60391 http://www.alumilite.com/ProdDetail.cfm?Category=Casting%20R esins&Name=Alumilite%20White

Resin cures rock-hard so your hollow object becomes rigid.
If you wanna fill your object to make it solid, this resin
will do you justice.
A 28oz. kit lasts a long way for small objects.

You can find it at local hobby stores.
If your local hobby store doesn't carry this brand
you can find it here... www.hobbylobby.com

Here's a catalog of resin types, for those who wanna
venture into Resin Casting, for making replicas of your
Shapeways printed models...
http://www.alumilite.com/Category.cfm?Category=Casting%20Res ins

Enjoy.

]]> magengar 2013-01-18T13:18:19-00:00 http://www.shapeways.com/forum/index.php?t=rview&goto=61885&th=979#msg_61885 bobquincy 2013-02-12T15:33:34-00:00