Home » Community » 3D modelers for hire » Model Train Shell Designer
Search Search  
Show: Today's Messages    Show Polls    Message Navigator
Model Train Shell Designer [message #57883] Sun, 02 December 2012 20:44 UTC Go to next message
avatar peterlanc  is currently offline peterlanc
Messages: 1
Registered: August 2011
Go to my shop
Junior Member
About me:
Single male with plenty of time on my hands living in middle earth!

Expertise:
I've done mostly New Zealand train shells on a scale of 1:120

Experience:
http://www.shapeways.com/shops/kiwitrains

Portfolio:
http://www.shapeways.com/shops/kiwitrains

Rate:
Reasonable, typically never ask for more than $20 per model.
Re: Model Train Shell Designer [message #58014 is a reply to message #57883 ] Wed, 05 December 2012 13:59 UTC Go to previous messageGo to next message
avatar bartv  is currently offline bartv
Messages: 1667
Registered: December 2007
Go to my shop
Shapie Expert
Hi peterlanc,

the links to your experience and portfolio are the same. I assume that wasn't intentional?

Bart


Community Manager Europe | Shapeways
Re: Model Train Shell Designer [message #67274 is a reply to message #57883 ] Wed, 01 May 2013 17:38 UTC Go to previous messageGo to next message
avatar mgbusa  is currently offline mgbusa
Messages: 1
Registered: September 2011
Go to all my models
Junior Member
I sent you a PM

[Updated on: Wed, 01 May 2013 17:40 UTC]

Re: Model Train Shell Designer [message #104301 is a reply to message #57883 ] Thu, 04 December 2014 09:35 UTC Go to previous messageGo to next message
avatar surftram20  is currently offline surftram20
Messages: 8
Registered: April 2013
Go to all my models
Junior Member
have you done any n scale models?
Re: Model Train Shell Designer [message #112156 is a reply to message #57883 ] Sat, 14 March 2015 23:20 UTC Go to previous messageGo to next message
avatar wlupoli  is currently offline wlupoli
Messages: 1
Registered: October 2014
Go to all my models
Junior Member
I have a need for an HO scale electric locomotive body shell. Need the software that can print the body shell. The body, actually the boxcab in the attached, is approximately 8.25inches long, and I'd like a wall thickness of no more than 1/16 inch. I don't need the pantographs, bells, lights, and other paraphernalia, but would like the window frames, louver, and rivets on the sides and front. The body will fit over the frame of a Bachmann HO Scale GG-1. The frame will contain the motor, electronics, speaker, and weights. Attached diagram is the full scale prototype. Also. Sample brass model is what you are copying. Question: would it be easier to just make a rubber mold of the body and then make copies out of resin? Of course, we may not get the wall thickness that way.

Bill

  • Attachment: EP-3 Diagram.JPG
    (Size: 129.60KB, Downloaded 11 time(s))

  • Attachment: EP-3.jpg
    (Size: 245.44KB, Downloaded 9 time(s))

Re: Model Train Shell Designer [message #112472 is a reply to message #104301 ] Thu, 19 March 2015 09:05 UTC Go to previous messageGo to next message
avatar Loweland  is currently offline Loweland
Messages: 1
Registered: March 2015
Go to my shop
Junior Member

[Updated on: Thu, 19 March 2015 09:07 UTC]

Re: Model Train Shell Designer [message #112821 is a reply to message #57883 ] Wed, 25 March 2015 19:39 UTC Go to previous message
avatar Buzzmodels  is currently offline Buzzmodels
Messages: 6
Registered: May 2012
Go to all my models
Junior Member
Pm sent regarding 3d work for uk trains.

Andy

 
   
Previous Topic:Jewelry 3d designer
Next Topic:Freelance 3D printable Prototypes, Scale Models, Characters, Animations

Logo

Hello.

We're sorry to inform you that we no longer support this browser and can't confirm that everything will work as expected. For the best Shapeways experience, please use one of the following browsers:

Click anywhere outside this window to continue.