by
virtox
Accused of being fake, witchcraft and simply impossible..
This kinetic sculpture is inspired by the unlimited freedom of 3d printing,
it wobbles and turns with a slight movement of the hand.
Now give it a good spin or puff of air and it erupts in erratic and wild behavior.
This is the 5cm / 2" version, see the Gyro the Forms section for other shapes and sizes.
Corner stand available separately, or get the complete set below!
NEW!
Now also available as a pendant/keyfob!
In both Extra small and Small
Instructions
It is composed of four concentric cubes, each one spinning around a different axis.
The model needs some minor assembly:
Each inner cube has two knobs which need to be placed into the corresponding clamps in the parent cube. It's easiest to start with the inner most and continue outward.
And then... spin it away !
Notes
Do not be alarmed if your cube will not run smoothly at first!
Because of minor variations as a result of the printing process,
some need to wear in a little but will loosen up very quickly.
In the example video I am blowing on it to make it move, it's that smooth.
Be a little careful with (the assembly of) the Alumide version as this material is slightly less flexible/robust than the Strong & Flexible materials.
Get a complete set.
A default set consists of an Alumide Gyro the Cube and a White stand, you can change the materials in your cart later.
+ 
This kinetic sculpture is inspired by the unlimited freedom of 3d printing,
it wobbles and turns with a slight movement of the hand.
Now give it a good spin or puff of air and it erupts in erratic and wild behavior.
This is the 5cm / 2" version, see the Gyro the Forms section for other shapes and sizes.
Corner stand available separately, or get the complete set below!
NEW!
Now also available as a pendant/keyfob!
In both Extra small and Small
Instructions
It is composed of four concentric cubes, each one spinning around a different axis.
The model needs some minor assembly:
Each inner cube has two knobs which need to be placed into the corresponding clamps in the parent cube. It's easiest to start with the inner most and continue outward.
And then... spin it away !
Notes
Do not be alarmed if your cube will not run smoothly at first!
Because of minor variations as a result of the printing process,
some need to wear in a little but will loosen up very quickly.
In the example video I am blowing on it to make it move, it's that smooth.
Be a little careful with (the assembly of) the Alumide version as this material is slightly less flexible/robust than the Strong & Flexible materials.
Get a complete set.
A default set consists of an Alumide Gyro the Cube and a White stand, you can change the materials in your cart later.
+ 
by
JoshuaHarker
The filigree design over the skull symbolizes ever growing renewal over the ghost of the past. This is the original design as featured on Kickstarter. It became their #1 most funded sculpture project of all time. Small is pictured sitting in the hand. See pic of all 3 sizes together for comparison.
by
TheoJansen
The third public evolution of the Animaris Geneticus Parvus. #7 has evolved legs, with pointy feet instead of flat. Featuring a fully working Theo Jansen mechanism as used in his work "the Rhinoceros".
Also see our new Propeller Propulsion add-on, to have your Strandbeest walk autonomously!
The mechanism is printed assembled, and will work without further assembly right after birth from the printer.
A few tips to consider:
- After birth there might be a little powder left in some joints, or it might not go supersmooth. This will fix itself after the animal has a little bit of practice!
- Some surfaces work better than others. The legs require a little friction, and a flat surface. So for example: A rough table or floor, thin flat carpeting, or a thin rubber sheet. It will slip on a too smooth surface.
- The best way to push it is by its nameplate. Do not push down, but forward.
- The beest is light, but quite strong. It can actually be dropped without breaking. It is not a "toy" however, and not suitable for children. The 3D printer material is easy to stain so clean hands are advised.
Also see our new Propeller Propulsion add-on, to have your Strandbeest walk autonomously!
The mechanism is printed assembled, and will work without further assembly right after birth from the printer.
A few tips to consider:
- After birth there might be a little powder left in some joints, or it might not go supersmooth. This will fix itself after the animal has a little bit of practice!
- Some surfaces work better than others. The legs require a little friction, and a flat surface. So for example: A rough table or floor, thin flat carpeting, or a thin rubber sheet. It will slip on a too smooth surface.
- The best way to push it is by its nameplate. Do not push down, but forward.
- The beest is light, but quite strong. It can actually be dropped without breaking. It is not a "toy" however, and not suitable for children. The 3D printer material is easy to stain so clean hands are advised.
by
TheoJansen
[Note: This propeller propulsion add-on does not include a 3D printed Strandbeest, which should be bought seperately! This propeller does not fit the Ondula version!]
Theo Jansen’s 3D printed Strandbeest continues to evolve with the addition of a Propeller Propulsion system! The 3D printed Strandbeests can now walk autonomously, powered by the wind, just like Theo's full-scale Strandbeests. The new propeller add-on gives new and existing owners of these kinetic sculptures a new way to set them in motion!
The propeller addition is available as a separate kit, which can be mounted on the 3D printed Strandbeests. The propeller is compatible with the various evolutions of the Strandbeest, so existing owners of the “AGP” 5 and 7 model Strandbeests can use it as well. Consisting of 5 main parts, it can be mounted on the Strandbeest body in a few simple steps.
Also see our videos of the Strandbeest Propulsion in action, and the video with mounting instructions.
The 3D printed Strandbeest is sold separately.
A few tips to consider:
- Please look at our instruction video on mounting the Propeller Propulsion add-on, here.
- After mounting the Propeller Propulsion add-on it is best left mounted. Frequent dis-assembly can wear down the material which can result in play on the mechanism.
Theo Jansen’s 3D printed Strandbeest continues to evolve with the addition of a Propeller Propulsion system! The 3D printed Strandbeests can now walk autonomously, powered by the wind, just like Theo's full-scale Strandbeests. The new propeller add-on gives new and existing owners of these kinetic sculptures a new way to set them in motion!
The propeller addition is available as a separate kit, which can be mounted on the 3D printed Strandbeests. The propeller is compatible with the various evolutions of the Strandbeest, so existing owners of the “AGP” 5 and 7 model Strandbeests can use it as well. Consisting of 5 main parts, it can be mounted on the Strandbeest body in a few simple steps.
Also see our videos of the Strandbeest Propulsion in action, and the video with mounting instructions.
The 3D printed Strandbeest is sold separately.
A few tips to consider:
- Please look at our instruction video on mounting the Propeller Propulsion add-on, here.
- After mounting the Propeller Propulsion add-on it is best left mounted. Frequent dis-assembly can wear down the material which can result in play on the mechanism.
by
isohedral
An espresso cup specially designed with fins, to ensure the successful deployment of your rocket fuel. All systems are go! Paraboloid bowl holds approximately 1.5 fl oz. or 45 mL. (Note that I previously claimed the cup held 60 mL. While my 3D modelling software still reports that as the internal volume, some combination of the printing process and glazing is robbing me of internal volume. Contact me if you'd be interested in a larger, more expensive 60 mL cup.)
After receiving feedback from Shapeways, I've created a slightly revised model for the cup. I'm told that this model will be easier to print and glaze, leading to a more reliable product. The changes are minor -- it's a little wider, a little heavier, and has more rounding on edges that were previously sharp (a 3D rendering shows the differences above).
Update (April 13th, 2013): The cup has had a great run on Shapeways, and I deeply appreciate the attention and positive feedback it has received. The bad news is that I've got to stop offering it for sale here. The good news is that the cup is now available commercially! It's being manufactured by Fred and Friends, sold under the name "Blast Off! Espresso Cup Set". It's already available for purchase online (perpetualkid.com, thinkgeek.com), and I'm sure you'll be able to find it in your favourite housewares store soon.
by
MichielCornelissen
Tool, symbol or both?
The bits on this pendant are based on actual bit sizes - including an IKEA standard tool - so 'a bit cross' can be used for light jobs. Just remember the steel isn't tempered like 'real' tool bits and tolerances may vary.
I recommend using it with a red leather cord of about 78 cm/ 31 inch.
If you are new to the Shapeways website: to order you will be asked to create an account (it's easy).
The bits on this pendant are based on actual bit sizes - including an IKEA standard tool - so 'a bit cross' can be used for light jobs. Just remember the steel isn't tempered like 'real' tool bits and tolerances may vary.
I recommend using it with a red leather cord of about 78 cm/ 31 inch.
If you are new to the Shapeways website: to order you will be asked to create an account (it's easy).
by
TheoJansen
The first public evolution of the Animaris Geneticus Parvus, #5. Featuring a fully working Theo Jansen mechanism as used in his work "the Rhinoceros". The mechanism is printed assembled, and will work without further assembly right after birth from the printer.
Also see our new Propeller Propulsion add-on, to have your Strandbeest walk autonomously!
A few tips to consider:
- After birth there might be a little powder left in some joints, or it might not go supersmooth. This will fix itself after the animal has a little bit of practice!
- Some surfaces work better than others. The legs require a little friction, and a flat surface. So for example: A rough table or floor, thin flat carpeting, or a thin rubber sheet.
- The best way to push it is by its nameplate. Do not push down, but forward
Also see our new Propeller Propulsion add-on, to have your Strandbeest walk autonomously!
A few tips to consider:
- After birth there might be a little powder left in some joints, or it might not go supersmooth. This will fix itself after the animal has a little bit of practice!
- Some surfaces work better than others. The legs require a little friction, and a flat surface. So for example: A rough table or floor, thin flat carpeting, or a thin rubber sheet.
- The best way to push it is by its nameplate. Do not push down, but forward
by
joabaldwin
The design is based on the classic Celtic-style knot symbol for the World Tree from Norse mythology, Yggdrasil.
Inside the leaves you can see a small sphere of blue. If you look reaaally carefully, you could notice that the continents in the blue ball are in the shape of Pangea and not our current distribution.
Inside the leaves you can see a small sphere of blue. If you look reaaally carefully, you could notice that the continents in the blue ball are in the shape of Pangea and not our current distribution.
by
virtox
Phamora Ceramics!
Is inside out? Or is it not? Perhaps both?
This is an Amphora from another space-time.
An ancient object which we knew had to exist.
And after years of excavation in other dimensions we finally found it!
A very exotic vase with a unique near-impossible shape, suitable for use with dry flowers and striking enough to stand alone.
Theoretically it can also hold water in the toroidal bottom part, read practical details below.
Very suitable as a wedding gift to symbolize love and infinity.
The number eight (or sideways infinity) plays an important role in this piece,
both in the number of arms and the cross-section of this model.
Notes:
To improve print quality and after some deliberation with production, this model has been slightly updated on August 24th 2012; The arms have been thickened and the holes enlarged to improve strength and glazing.
Still I recommend not to put a lot of stress on the handles.
Refer to rendered images for the latest version. I will update photo's asap.
The bottom it stands on, is unglazed, which is invisible during normal display.
All clearly visible parts will be fully glazed, but there is a chance some parts on in the inside might not, which may compromise it's ability to hold water.
While production does their absolute best and all recent prints turned out perfectly glazed and hold water, due to the complexities involved, there is no 100% guarantee for to be absolutely watertight.
Is inside out? Or is it not? Perhaps both?
This is an Amphora from another space-time.
An ancient object which we knew had to exist.
And after years of excavation in other dimensions we finally found it!
A very exotic vase with a unique near-impossible shape, suitable for use with dry flowers and striking enough to stand alone.
Theoretically it can also hold water in the toroidal bottom part, read practical details below.
Very suitable as a wedding gift to symbolize love and infinity.
The number eight (or sideways infinity) plays an important role in this piece,
both in the number of arms and the cross-section of this model.
Notes:
To improve print quality and after some deliberation with production, this model has been slightly updated on August 24th 2012; The arms have been thickened and the holes enlarged to improve strength and glazing.
Still I recommend not to put a lot of stress on the handles.
Refer to rendered images for the latest version. I will update photo's asap.
The bottom it stands on, is unglazed, which is invisible during normal display.
All clearly visible parts will be fully glazed, but there is a chance some parts on in the inside might not, which may compromise it's ability to hold water.
While production does their absolute best and all recent prints turned out perfectly glazed and hold water, due to the complexities involved, there is no 100% guarantee for to be absolutely watertight.
by
MichaelMueller
No matter what everyone say... you deserve it!
It is written on the ring to remember you about this fact.
The default Ring Size is US 8.
Large diameter rings (sizes 10 - 12) have seven instead of six spikes... to fit nice.
Use one of the following links to choose a different ring size.
US Ring Size 4
Inside Diameter: 14.88 mm / 0.586 in
Inside circumference: 46.80 mm / 1.84 in
US Ring Size 5.5
Inside Diameter: 16.10 mm / 0.634 in
Inside circumference: 50.60 mm / 1.99 in
US Ring Size 6.5
Inside Diameter: 16.92 mm / 0.666 in
Inside circumference: 53.15 mm / 2.09 in
US Ring Size 7
Inside Diameter: 17.32 mm / 0.682 in
Inside circumference: 54.41 mm / 2.14 in
US Ring Size 8 (default)
Inside Diameter: 18.14 mm / 0.714 in
Inside circumference: 56.86 mm / 2.24 in
US Ring Size 8.5
Inside Diameter: 18.54 mm / 0.73 in
Inside circumference: 58.3 mm / 2.29 in
US Ring Size 9
Inside Diameter: 18.95 mm / 0.746 in
Inside circumference: 59.69 mm / 2.34 in
US Ring Size 10
Inside Diameter: 19.76 mm / 0.778 in
Inside circumference: 62.20 mm / 2.44 in
US Ring Size 11
Inside Diameter: 20.57 mm / 0.81 in
Inside circumference: 64.72 mm / 2.54 in
US Ring Size 12
Inside Diameter: 21.39 mm / 0.842 in
Inside circumference: 67.23 mm / 2.65 in
Other size needed? Just send me a message!
Note:
The silver material is very bright and shiny. Some designs look much better when deeper parts are blackened. You can do this easily by yourself by putting the silver jewelry in a small glass with bleach for a few minutes. After it turns dark, you can polish it partial with a sponge or a towel.
It is written on the ring to remember you about this fact.
The default Ring Size is US 8.
Large diameter rings (sizes 10 - 12) have seven instead of six spikes... to fit nice.
Use one of the following links to choose a different ring size.
US Ring Size 4
Inside Diameter: 14.88 mm / 0.586 in
Inside circumference: 46.80 mm / 1.84 in
US Ring Size 5.5
Inside Diameter: 16.10 mm / 0.634 in
Inside circumference: 50.60 mm / 1.99 in
US Ring Size 6.5
Inside Diameter: 16.92 mm / 0.666 in
Inside circumference: 53.15 mm / 2.09 in
US Ring Size 7
Inside Diameter: 17.32 mm / 0.682 in
Inside circumference: 54.41 mm / 2.14 in
US Ring Size 8 (default)
Inside Diameter: 18.14 mm / 0.714 in
Inside circumference: 56.86 mm / 2.24 in
US Ring Size 8.5
Inside Diameter: 18.54 mm / 0.73 in
Inside circumference: 58.3 mm / 2.29 in
US Ring Size 9
Inside Diameter: 18.95 mm / 0.746 in
Inside circumference: 59.69 mm / 2.34 in
US Ring Size 10
Inside Diameter: 19.76 mm / 0.778 in
Inside circumference: 62.20 mm / 2.44 in
US Ring Size 11
Inside Diameter: 20.57 mm / 0.81 in
Inside circumference: 64.72 mm / 2.54 in
US Ring Size 12
Inside Diameter: 21.39 mm / 0.842 in
Inside circumference: 67.23 mm / 2.65 in
Other size needed? Just send me a message!
Note:
The silver material is very bright and shiny. Some designs look much better when deeper parts are blackened. You can do this easily by yourself by putting the silver jewelry in a small glass with bleach for a few minutes. After it turns dark, you can polish it partial with a sponge or a towel.
by
arthurditlef
ARTIFICIAL NATURE SERIES
Inspired by Nature, with an artificial twist.
Inspired by Nature, with an artificial twist.
by
MichaelMueller
Harr, harr, pirate stuff.
Ship ahoy!
The default Ring Size is US 6.5.
Use one of the following links to choose a different ring size.
US Ring Size 4
Inside Diameter: 14.88 mm / 0.586 in
Inside circumference: 46.80 mm / 1.84 in
US Ring Size 5
Inside Diameter: 15.7 mm / 0.618 in
Inside circumference: 49.3 mm / 1.94 in
US Ring Size 5.5
Inside Diameter: 16.1 mm / 0.634 in
Inside circumference: 50.6 mm / 1.99 in
US Ring Size 6.5 (default)
Inside Diameter: 16.92 mm / 0.666 in
Inside circumference: 53.15 mm / 2.09 in
US Ring Size 7
Inside Diameter: 17.32 mm / 0.682 in
Inside circumference: 54.41 mm / 2.14 in
US Ring Size 8
Inside Diameter: 18.14 mm / 0.714 in
Inside circumference: 56.86 mm / 2.24 in
US Ring Size 9
Inside Diameter: 18.95 mm / 0.746 in
Inside circumference: 59.69 mm / 2.34 in
US Ring Size 10
Inside Diameter: 19.76 mm / 0.778 in
Inside circumference: 62.20 mm / 2.44 in
US Ring Size 11
Inside Diameter: 20.57 mm / 0.81 in
Inside circumference: 64.72 mm / 2.54 in
US Ring Size 12
Inside Diameter: 21.39 mm / 0.842 in
Inside circumference: 67.23 mm / 2.65 in
Other size needed? Just send me a message!
Ship ahoy!
The default Ring Size is US 6.5.
Use one of the following links to choose a different ring size.
US Ring Size 4
Inside Diameter: 14.88 mm / 0.586 in
Inside circumference: 46.80 mm / 1.84 in
US Ring Size 5
Inside Diameter: 15.7 mm / 0.618 in
Inside circumference: 49.3 mm / 1.94 in
US Ring Size 5.5
Inside Diameter: 16.1 mm / 0.634 in
Inside circumference: 50.6 mm / 1.99 in
US Ring Size 6.5 (default)
Inside Diameter: 16.92 mm / 0.666 in
Inside circumference: 53.15 mm / 2.09 in
US Ring Size 7
Inside Diameter: 17.32 mm / 0.682 in
Inside circumference: 54.41 mm / 2.14 in
US Ring Size 8
Inside Diameter: 18.14 mm / 0.714 in
Inside circumference: 56.86 mm / 2.24 in
US Ring Size 9
Inside Diameter: 18.95 mm / 0.746 in
Inside circumference: 59.69 mm / 2.34 in
US Ring Size 10
Inside Diameter: 19.76 mm / 0.778 in
Inside circumference: 62.20 mm / 2.44 in
US Ring Size 11
Inside Diameter: 20.57 mm / 0.81 in
Inside circumference: 64.72 mm / 2.54 in
US Ring Size 12
Inside Diameter: 21.39 mm / 0.842 in
Inside circumference: 67.23 mm / 2.65 in
Other size needed? Just send me a message!
by
COVO
Product Name "Screwdriver Ring". Designed by Japan.
Available in either stainless steel (antique bronze & gold plated)
The default size is 20.6 mm inner diameter but you can customize the size to your liking.
Click personalize to choose your US ring size.(Size support: # 8 to # 13.)
Please refer to a this page.
Conversion chart for ring sizes
US Ring Size Inside diameter
8 18.1mm
9 19.0mm
10 19.8mm
11 20.6mm
12 21.4mm
13 22.2mm
Please also see other designs.
Shop here.
http://www.shapeways.com/shops/forma
FORMA Laboratory Facebook Page!
Available in either stainless steel (antique bronze & gold plated)
The default size is 20.6 mm inner diameter but you can customize the size to your liking.
Click personalize to choose your US ring size.(Size support: # 8 to # 13.)
Please refer to a this page.
Conversion chart for ring sizes
US Ring Size Inside diameter
8 18.1mm
9 19.0mm
10 19.8mm
11 20.6mm
12 21.4mm
13 22.2mm
Please also see other designs.
Shop here.
http://www.shapeways.com/shops/forma
FORMA Laboratory Facebook Page!
by
arthurditlef
ARTIFICIAL NATURE SERIES
Inspired by Nature, with an artificial twist.
New Version! More support added so it is now harder to fall due pen weight.
Inspired by Nature, with an artificial twist.
New Version! More support added so it is now harder to fall due pen weight.
by
COVO
Product Name "Brick Ring". Designed by Japan.
Want to know more puroduct detail? Watch movie.
The material of movie is Silver Glossy.
Available in either stainless steel (antique bronze & gold plated) or silver.
The default size is 20.6 mm inner diameter but you can customize the size to your liking.
Click personalize to choose your US ring size.(Size support: # 8 to # 13.)
The brick can be attached by all the sizes.
Please refer to a this page.
Conversion chart for ring sizes
US Ring Size Inside diameter
8 18.1mm
9 19.0mm
10 19.8mm
11 20.6mm
12 21.4mm
13 22.2mm
Please also see other designs.
Shop here.
http://www.shapeways.com/shops/forma
Want to know more puroduct detail? Watch movie.
The material of movie is Silver Glossy.
Available in either stainless steel (antique bronze & gold plated) or silver.
The default size is 20.6 mm inner diameter but you can customize the size to your liking.
Click personalize to choose your US ring size.(Size support: # 8 to # 13.)
The brick can be attached by all the sizes.
Please refer to a this page.
Conversion chart for ring sizes
US Ring Size Inside diameter
8 18.1mm
9 19.0mm
10 19.8mm
11 20.6mm
12 21.4mm
13 22.2mm
Please also see other designs.
Shop here.
http://www.shapeways.com/shops/forma
by
cooldjez
This is an awesome looking ring, but it's still comfortable to wear.
Contact me if you want a size outside of the co-creator range. I can also provide this ring on request in a plastic material for casting in silver or gold.
Contact me if you want a size outside of the co-creator range. I can also provide this ring on request in a plastic material for casting in silver or gold.
by
susantio
An elegant and modern vase inspired by the Japanese paper-folding craft. Height 28 cm.
by
COVO
Product Name "Cat Skull Ring". Designed by Japan.
Want to know more puroduct detail? Watch movie.
The material of movie is Silver Glossy.
Available in either stainless steel (antique bronze & gold plated) or silver.
The default size is 20.6 mm inner diameter but you can customize the size to your liking.
Click personalize to choose your US ring size.(Size support: # 8 to # 11.)
Please refer to a this page.
Conversion chart for ring sizes
US Ring Size Inside diameter
8 18.1mm
9 19.0mm
10 19.8mm
11 20.6mm
Please also see other designs.
Shop here.
http://www.shapeways.com/shops/forma
Want to know more puroduct detail? Watch movie.
The material of movie is Silver Glossy.
Available in either stainless steel (antique bronze & gold plated) or silver.
The default size is 20.6 mm inner diameter but you can customize the size to your liking.
Click personalize to choose your US ring size.(Size support: # 8 to # 11.)
Please refer to a this page.
Conversion chart for ring sizes
US Ring Size Inside diameter
8 18.1mm
9 19.0mm
10 19.8mm
11 20.6mm
Please also see other designs.
Shop here.
http://www.shapeways.com/shops/forma
by
archenemy76
Other Sizes available: scroll down to see.
When I model in 3D it often feels like I'm sculpting. I build each piece, put it into place, tweak/adjust, then add the next piece. With the Triangulated cuff I really wanted a design that seemed minimal yet dynamic, and I adjusted my model until I got the effect I was satisfied with. The final result was 3D printed in a black plastic nylon material (BSF - Black Strong & Flexible). It's a very lightweight yet strong and flexible material (as the name implies). The ends of the cuff are rounded so it slides on and off easily.
Sizing:
*Size Extra-Small/Petite interior dimensions: 2 1/8 inches wide x 1 1/2 inches tall [54mmx38mm]. Available from Shapeways here: http://shpws.me/3qW1
*Size Small interior dimensions: 2 1/4 inches wide x 1 3/4 inches tall [57mmx44.5mm]. Available from Shapeways here: http://shpws.me/3qW0
*Size Medium interior dimensions : 2 1/3 inches wide x 2 inches tall [59mmx51mm]. Available from Shapeways here: http://shpws.me/3qW2
by
MacBurro
A Little SteamPunk World Model for Desk Decoration
by
COVO
Headphone Jack Accessory.
Fits in the 3.5mm headphone jack.
Dress up and prettify your iPods, smartphones, and music players.
It prevents dirt from getting into the earphone jack.
Fits in the 3.5mm headphone jack.
Dress up and prettify your iPods, smartphones, and music players.
It prevents dirt from getting into the earphone jack.
by
{DF}
This case has been designed following Apple's strict guidelines for iPhone cases - this assures a precise and tight fit and unconstrained functionality.
Protection
The Strong & Flexible material from Shapeways is durable enough to keep your iPhone completely safe when dropped. It can be combined with commercially available screen protectors. I would recommend combining it with the InvisibleShield for a nice combo protection.
Also, it is dishwasher-safe. If your case gets dirty over time, put it in your dishwasher and it will look brand new!
If you find that you accidentally touch the part of the iPhone antenna that reduces reception, you won't have that problem with this case. If you usually talk with your iPhone in your left hand, and if you are often in areas with marginal signal coverage, this case will make it less likely for you to lose a signal and drop a call.
Playing games or using the GPS raises your iPhone's body heat much. That's because you use your CPU at max. According to Apple's knowledge-base, if the interior temperature of the device exceeds normal operating temperatures, you may experience the following as it attempts to regulate its temperature: Device stops charging, Display dims, Weak cellular signal, Camera flash is disabled, Temperature warning screen appears with the message "iPhone needs to cool down before you can use it". To help your iPhone keep normal operating temperatures, you should use a bumper or a case such as this one, since it does not cover the back of the iPhone and does not trap the heat inside.
Design
This case doesn't distract much from the feel of the iPhone. It has the advantage of being the "un-case" because it is so minimal and does not cover the front or the back of the iPhone. Neither the sides.
It doesn't distract from the design of the iPhone either. The problem with traditional cases is that they completely cover up the iPhone. Using a traditional case you end up feeling like you are holding rubber in your hand when you hold your iPhone. The iPhone's design is really amazing and it would be a pity to hide. The case allows both the design to show and a quite smooth feel instead.
Easy to use
This case allows to plug in the 30-pin dock connector without removing the case, while all controls and connections remain accessible.
Materials
Recommended material for purchase: Strong & Flexible (any color).
Make sure that you check under 'Select Material' for currently available color options.
Instructions
To put the iPhone in the case, start at one of the top corners. To take it out, start from the bottom corners where there are no buttons.
Protection
The Strong & Flexible material from Shapeways is durable enough to keep your iPhone completely safe when dropped. It can be combined with commercially available screen protectors. I would recommend combining it with the InvisibleShield for a nice combo protection.
Also, it is dishwasher-safe. If your case gets dirty over time, put it in your dishwasher and it will look brand new!
If you find that you accidentally touch the part of the iPhone antenna that reduces reception, you won't have that problem with this case. If you usually talk with your iPhone in your left hand, and if you are often in areas with marginal signal coverage, this case will make it less likely for you to lose a signal and drop a call.
Playing games or using the GPS raises your iPhone's body heat much. That's because you use your CPU at max. According to Apple's knowledge-base, if the interior temperature of the device exceeds normal operating temperatures, you may experience the following as it attempts to regulate its temperature: Device stops charging, Display dims, Weak cellular signal, Camera flash is disabled, Temperature warning screen appears with the message "iPhone needs to cool down before you can use it". To help your iPhone keep normal operating temperatures, you should use a bumper or a case such as this one, since it does not cover the back of the iPhone and does not trap the heat inside.
Design
This case doesn't distract much from the feel of the iPhone. It has the advantage of being the "un-case" because it is so minimal and does not cover the front or the back of the iPhone. Neither the sides.
It doesn't distract from the design of the iPhone either. The problem with traditional cases is that they completely cover up the iPhone. Using a traditional case you end up feeling like you are holding rubber in your hand when you hold your iPhone. The iPhone's design is really amazing and it would be a pity to hide. The case allows both the design to show and a quite smooth feel instead.
Easy to use
This case allows to plug in the 30-pin dock connector without removing the case, while all controls and connections remain accessible.
Materials
Recommended material for purchase: Strong & Flexible (any color).
Make sure that you check under 'Select Material' for currently available color options.
Instructions
To put the iPhone in the case, start at one of the top corners. To take it out, start from the bottom corners where there are no buttons.
by
Mezmera
This arrow-shaped ring wraps around your finger. It can be worn as a single ring, simple and elegant, or with two or three creating a zigzag pattern.
The left version has its left side below the right side of the ring, making a perfect fit on your left ring finger or little finger. The 'right' version is the same design, but mirrored, for your right ring finger or little finger.
This ring is US size 6 and for the left hand. For ordering other sizes (see this chart to find your ring size), click on the buttons below after selecting the right material in the upper right corner of the page.
Size 6 - right Size 6 1/2 - left Size 6 1/2 - right Size 7 - left Size 7 - right Size 7 1/2 - left Size 7 1/2 - right Size 8 - left Size 8 - right Size 8 1/2 - left Size 8 1/2 - right Size 9 - left Size 9 - right Size 10 - left Size 10 - right Size 11 - left Size 11 - right
Is your ring size not listed? No problem, just contact me via the 'Contact Designer' button (upper right corner) and I'll try to make it available within 24 hours.
by
MacBurro
A Medium Steampunk Themed Model of a World for desk decorations
by
COVO
Product Name "Techno Ring". Designed by Japan.
Want to know more puroduct detail? Watch movie.
The material of movie is Silver Glossy.
Available in either stainless steel (antique bronze & gold plated) or silver.
The default size is 20.6 mm inner diameter but you can customize the size to your liking.
Click personalize to choose your US ring size.(Size support: # 8 to # 13.)
Please refer to a this page.
Conversion chart for ring sizes
US Ring Size Inside diameter
8 18.1mm
9 19.0mm
10 19.8mm
11 20.6mm
12 21.4mm
13 22.2mm
Please also see other designs.
Shop here.
http://www.shapeways.com/shops/forma
Want to know more puroduct detail? Watch movie.
The material of movie is Silver Glossy.
Available in either stainless steel (antique bronze & gold plated) or silver.
The default size is 20.6 mm inner diameter but you can customize the size to your liking.
Click personalize to choose your US ring size.(Size support: # 8 to # 13.)
Please refer to a this page.
Conversion chart for ring sizes
US Ring Size Inside diameter
8 18.1mm
9 19.0mm
10 19.8mm
11 20.6mm
12 21.4mm
13 22.2mm
Please also see other designs.
Shop here.
http://www.shapeways.com/shops/forma
by
Eeppium
A ring with crystals growing from it .
Printed from Stainless Steel
Hole diameter 21,30mm size 12
*It is recommended to add clear nailpolish to the innerparts, that are in contact with skin*
See also the earrings to go with the ring Crystal Earring
Printed from Stainless Steel
Hole diameter 21,30mm size 12
*It is recommended to add clear nailpolish to the innerparts, that are in contact with skin*
See also the earrings to go with the ring Crystal Earring
by
COVO
Product Name "Cat Ring". Designed by Japan.
Want to know more puroduct detail? Watch movie.
The material of movie is Silver Glossy.
Available in either stainless steel (antique bronze & gold plated) or silver.
You can customize the size to your liking.
Click personalize to choose your US ring size.(Size support: # 8 to # 13.)
Please refer to a this page.
Conversion chart for ring sizes
US Ring Size Inside diameter
8 18.1mm
9 19.0mm
10 19.8mm
11 20.6mm
12 21.4mm
13 22.2mm
Please also see other designs.
Shop here.
http://www.shapeways.com/shops/forma
Want to know more puroduct detail? Watch movie.
The material of movie is Silver Glossy.
Available in either stainless steel (antique bronze & gold plated) or silver.
You can customize the size to your liking.
Click personalize to choose your US ring size.(Size support: # 8 to # 13.)
Please refer to a this page.
Conversion chart for ring sizes
US Ring Size Inside diameter
8 18.1mm
9 19.0mm
10 19.8mm
11 20.6mm
12 21.4mm
13 22.2mm
Please also see other designs.
Shop here.
http://www.shapeways.com/shops/forma
by
Innovo
The ''Skull'' Keychain / Pendant Multitool is both a decorative as well as practical keychain accessory.
It can be used for screwing, puncturing, cutting, nail removal and even cable stripping.
It can be carried in a keychain, worn as a pendant or used as a decorative fob.
''Skull'' Multitool specifications:
Length: 2,7 cm / Height: 3,2 cm / Width: 0,3 cm / Weight: 7gr
Available in several finishes and materials (Stainless Steel, Antique Bronze Matte, Antique Bronze Glossy, Gold Plated Matte, Gold Plated Glossy). Please choose from the right.
by
arthurditlef
ARTIFICIAL NATURE SERIES
Inspired by Nature, with an artificial twist.
Inspired by Nature, with an artificial twist.
by
lauradangerous
Abstract folded design ring with pointed ends and a crumpled paper look.
Recommended in White Strong & Flexible and Stainless Steel. White Detail for a beautiful snow-like matte finish (though not as durable)
by
COVO
Product Name "Puzzle Ring". Designed by Japan.
Want to know more puroduct detail? Watch movie.
The material of movie is Silver Glossy.
Available in either stainless steel (antique bronze & gold plated) or silver.
You can customize the size to your liking.
Click personalize to choose your US ring size.(Size support: # 8 to # 13.)
Please refer to a this page.
Conversion chart for ring sizes
US Ring Size Inside diameter
8 18.1mm
9 19.0mm
10 19.8mm
11 20.6mm
12 21.4mm
13 22.2mm
Please also see other designs.
Shop here.
http://www.shapeways.com/shops/forma
Want to know more puroduct detail? Watch movie.
The material of movie is Silver Glossy.
Available in either stainless steel (antique bronze & gold plated) or silver.
You can customize the size to your liking.
Click personalize to choose your US ring size.(Size support: # 8 to # 13.)
Please refer to a this page.
Conversion chart for ring sizes
US Ring Size Inside diameter
8 18.1mm
9 19.0mm
10 19.8mm
11 20.6mm
12 21.4mm
13 22.2mm
Please also see other designs.
Shop here.
http://www.shapeways.com/shops/forma
