by
curvecreative
Nanolet
Everyone's wearing their Nano on their wrist nowadays, now you can wear it on a one part 3D printed nano bracelet.
The NANOLET simply wraps around your wrist and fits snugly up to your hand which is perfect for running and everyday use. An alternative to the plethora of nano watches that are around now.
Featured on: Mashable , Cult of Mac , Yanko Design and many more.
Suitable for medium sized wrists. Available in a range of colors
Medium is for a wrist of circumference 165mm - 185mm. The best way to measure your wrist is to wrap a piece of string around your wrist, mark it and then measure it. Maximum wrist size is 190mm.
Unboxing Video here
Click here for OTHER SIZES
Click here to visit our site
Or click here to keep up to date on Facebook
Interested in buying Nanolets in BULK at reduced price? For LARGE , MEDIUM and SMALL
by
s_f_x
Update: I am currently working on an updated version, which is more robust and uses a more conventional 3-axis design (one servo per axis). I will leave this model available for spare parts. The new model is currently being tested and should be available soon.
This is a 3-axis gyro-stabilsation gimbal for the GoPro HD Hero camera. Intended use is for aerial video and first-person view (FPV) flying.
(Picture shows all the parts - camera is not included, and this is model here is only the back cage. Check the 3D model to see it. For the complete kit you have to order the back cage, the front lid, the servo cage and the mounting arm. You will also need 3x MKS470 servos, and a 16mm x 8mm ball bearing, not shown)
Video demonstration:
Assembly and servo test
Preliminary Gyro stabilisation test
Current status:
This is still work in progress - the current version has been slightly improved from the version in the video (I strengthened some of the elastic parts and improved the balancing). The gyro control board is my own design and currently not available yet. I will post an update once it is. The IMU is my design as well, and is available here.
You are welcome to order this design now, but be aware that it's still somewhat "beta". Whatever you do with it is entirely your own risk and responsibility, I unfortunately cannot make any claims towards its usefulness, stability or safety...
I would recommend, before you put this on a flying contraption, consider using a safety string to attach the camera to the plane somehow. GoPro cameras are very robust inside their waterproof case, but not quite so robust without that protection. They don't like crashing into the ground (and trust me, I know - as is probably obvious from the picture of my camera... in all fairness, it did mostly survive...)
Assembly instructions
For the complete kit you have to order the back cage, the front lid, the servo cage and the mounting arm. The bearing at the top is a 16mm outer, 8mm inner diameter ball bearing, available from many places. Hobbyking sells those as well.
I will possibly modify the mounting bracket in the future and also offer one with a smaller bearing... this one is total overkill! :)
The servos that will fit are the MKS DS470 (available e.g. from Hobbyking). They do have a little play, but they are very smooth and by far the fastest servo I've seen in that size and price class. I'm still on the lookout for different servos that might be a bit smoother.
Assembly:
1) Press the servos onto the mounting bracket and the flexible arms of the back cage. What works quite well is to carefully push it on just a little (best to put the printed piece onto a flat surface, and gently push the servo in just a bit to align). Then use a screw (maybe with a washer to spread the force), and slowly pull the arm onto the crown. You only have to do that once, it'll be a tight, smooth fit afterwards.
Remove the servos again after this step.
2) Mount the 3 servos on the servo mounting frame. Start with the yaw servo (the vertical one in the middle).The yaw servo crown has to face downwards (might be a bit fiddly). Make sure the crown of the yaw servo is aligned with the little stub axle on the opposite side. The two roll/pitch servos have to be inserted so that the crown faces the camera (towards the flat side of the mounting arm).
3) Press the mounting bracket onto the yaw servo crown, and put in the screw to hold it in place. On the opposite side, press in the 16mm/8mm ball bearing.
4) Carefully push the disk-shaped closure knob into the cylinder at the top of the camera back cage. You might need to rotate it a bit to ease it into place
5) Push the flexible arms of the back cage onto the two roll/pitch servos, and fix with screws.
-- Update: Seems the MKS has too much gain for the yaw axis, and tends to oscillate a bit with all that weight swinging around. They are fine for the Pitch/Roll arms. I'm still looking for a small servo with high speed, smoothness and no (or little) play... Suggestions are of course welcome!!
-- The servos are still a very tight fit into the control arms and the bracket. I already made it a bit larger, but still not enough. What works quite well is to carefully push it on just a little (best to put the arms onto a flat surface, and gently push the servo in just a bit to align). Then use a screw (maybe with a washer to spread the force), and slowly pull the arm onto the crown. You only have to do that once, it'll be a tight, smooth fit afterwards.
This is a 3-axis gyro-stabilsation gimbal for the GoPro HD Hero camera. Intended use is for aerial video and first-person view (FPV) flying.
(Picture shows all the parts - camera is not included, and this is model here is only the back cage. Check the 3D model to see it. For the complete kit you have to order the back cage, the front lid, the servo cage and the mounting arm. You will also need 3x MKS470 servos, and a 16mm x 8mm ball bearing, not shown)
Video demonstration:
Assembly and servo test
Preliminary Gyro stabilisation test
Current status:
This is still work in progress - the current version has been slightly improved from the version in the video (I strengthened some of the elastic parts and improved the balancing). The gyro control board is my own design and currently not available yet. I will post an update once it is. The IMU is my design as well, and is available here.
You are welcome to order this design now, but be aware that it's still somewhat "beta". Whatever you do with it is entirely your own risk and responsibility, I unfortunately cannot make any claims towards its usefulness, stability or safety...
I would recommend, before you put this on a flying contraption, consider using a safety string to attach the camera to the plane somehow. GoPro cameras are very robust inside their waterproof case, but not quite so robust without that protection. They don't like crashing into the ground (and trust me, I know - as is probably obvious from the picture of my camera... in all fairness, it did mostly survive...)
Assembly instructions
For the complete kit you have to order the back cage, the front lid, the servo cage and the mounting arm. The bearing at the top is a 16mm outer, 8mm inner diameter ball bearing, available from many places. Hobbyking sells those as well.
I will possibly modify the mounting bracket in the future and also offer one with a smaller bearing... this one is total overkill! :)
The servos that will fit are the MKS DS470 (available e.g. from Hobbyking). They do have a little play, but they are very smooth and by far the fastest servo I've seen in that size and price class. I'm still on the lookout for different servos that might be a bit smoother.
Assembly:
1) Press the servos onto the mounting bracket and the flexible arms of the back cage. What works quite well is to carefully push it on just a little (best to put the printed piece onto a flat surface, and gently push the servo in just a bit to align). Then use a screw (maybe with a washer to spread the force), and slowly pull the arm onto the crown. You only have to do that once, it'll be a tight, smooth fit afterwards.
Remove the servos again after this step.
2) Mount the 3 servos on the servo mounting frame. Start with the yaw servo (the vertical one in the middle).The yaw servo crown has to face downwards (might be a bit fiddly). Make sure the crown of the yaw servo is aligned with the little stub axle on the opposite side. The two roll/pitch servos have to be inserted so that the crown faces the camera (towards the flat side of the mounting arm).
3) Press the mounting bracket onto the yaw servo crown, and put in the screw to hold it in place. On the opposite side, press in the 16mm/8mm ball bearing.
4) Carefully push the disk-shaped closure knob into the cylinder at the top of the camera back cage. You might need to rotate it a bit to ease it into place
5) Push the flexible arms of the back cage onto the two roll/pitch servos, and fix with screws.
-- Update: Seems the MKS has too much gain for the yaw axis, and tends to oscillate a bit with all that weight swinging around. They are fine for the Pitch/Roll arms. I'm still looking for a small servo with high speed, smoothness and no (or little) play... Suggestions are of course welcome!!
-- The servos are still a very tight fit into the control arms and the bracket. I already made it a bit larger, but still not enough. What works quite well is to carefully push it on just a little (best to put the arms onto a flat surface, and gently push the servo in just a bit to align). Then use a screw (maybe with a washer to spread the force), and slowly pull the arm onto the crown. You only have to do that once, it'll be a tight, smooth fit afterwards.
by
MichielCornelissen
Don’t let unruly wires get between you and your music. Pod à porter is the easiest way to wear your music, and it’s now available for the iPod shuffle 4th generation.
Manufactured from tough but flexible, 3D-printed polyamide, Pod à porter is ultralight and has a finely textured surface finish; each ordered product is manufactured just for you. It fits the iPod shuffle 4th generation and its earbuds, leaving all controls accessible. It also works with other Apple earphones, including ones with a built-in remote control - make sure the plug is the same shape and size as the 4th generation shuffle's.
If you're new to the Shapeways site: to order, you'll be asked to create an account; you can sign in with twitter or facebook. Available in black, and limited edition colors shown below; check the support/materials section of this website for more information. Pod à porter is great for walking, strolling, commuting and many other activities, but it has not been specifically designed or tested for use during work-outs or sports, so it may not be suitable for your particular type of exercise. Product is shipped in basic Shapeways packaging.
Assembly is easy: just run the headphone wire through the product, and attach the Ipod shuffle. Have a look here for some images. If you have any feedback or questions on this item, please feel free to contact me directly through michiel-at-michielcornelissen-dot-com.
Some of the mentions of Pod à porter when it was originally released:
Wear your shuffle and nothing else...
gizmodo.com
Pod à porter, a 3d-printed iPod shuffle necklace
wired.com
Wanted: the cleverest way to wear an iPod shuffle
fastcodesign.com
Very smart.
joshspear.com
mocoloco.com
notcot.org
ilounge.com
design-milk.com
NY Times mentions Pod å`porter!
nytimes.com
Manufactured from tough but flexible, 3D-printed polyamide, Pod à porter is ultralight and has a finely textured surface finish; each ordered product is manufactured just for you. It fits the iPod shuffle 4th generation and its earbuds, leaving all controls accessible. It also works with other Apple earphones, including ones with a built-in remote control - make sure the plug is the same shape and size as the 4th generation shuffle's.
If you're new to the Shapeways site: to order, you'll be asked to create an account; you can sign in with twitter or facebook. Available in black, and limited edition colors shown below; check the support/materials section of this website for more information. Pod à porter is great for walking, strolling, commuting and many other activities, but it has not been specifically designed or tested for use during work-outs or sports, so it may not be suitable for your particular type of exercise. Product is shipped in basic Shapeways packaging.
Assembly is easy: just run the headphone wire through the product, and attach the Ipod shuffle. Have a look here for some images. If you have any feedback or questions on this item, please feel free to contact me directly through michiel-at-michielcornelissen-dot-com.
Some of the mentions of Pod à porter when it was originally released:
Wear your shuffle and nothing else...
gizmodo.com
Pod à porter, a 3d-printed iPod shuffle necklace
wired.com
Wanted: the cleverest way to wear an iPod shuffle
fastcodesign.com
Very smart.
joshspear.com
mocoloco.com
notcot.org
ilounge.com
design-milk.com
NY Times mentions Pod å`porter!
nytimes.com
by
lens42
Make your own slide-on macro lens for the iPhone 4 or 4S. I designed this for my iPhone 4 when I couldn't find the image quality I wanted for less than $60.
Print this model and then buy the glass lens for $4 from Surplus Shed (http://www.surplusshed.com/). The Surplus Shed part number is L4471. For some reason the search box on the Surplus Shed home page does not work with part numbers. To get to L4471, use the "Lens Finder". In the Lens Finder type:
Print this model and then buy the glass lens for $4 from Surplus Shed (http://www.surplusshed.com/). The Surplus Shed part number is L4471. For some reason the search box on the Surplus Shed home page does not work with part numbers. To get to L4471, use the "Lens Finder". In the Lens Finder type:
Lens Type: PCX, Plano Convex
Diameter: 12mm to 12mm
Focal length: 51mm to 51mm
It will get you to L4471
The lens fits in a recess in the model and is held in place with a few tiny drops of Superglue. If you get any glue on the lens it can cleaned off with nail polish remover or acetone. The lens is plano-convex (one side is flat). When inserted in the holder, the flat side of the lens faces the phone.
Note that the lens fits pretty snugly into the opening. Try fitting the lens before applying any glue. A good technique is, with the lens holder laying face-down on a table, lay the lens in position, and then push it into the recess by poking the lens with the eraser-end of a pencil. Once you know the lens fits cleanly, push it back out and put two tiny drops of superglue on opposite edges of the opening. I use a toothpick to apply the glue because squeezing the superglue directly out of the tube risks putting on too much. Then push the lens back in the same way as in the test fit.
The object pictures in the photo gallery (dime, ruler, and watch) are unedited and uncropped shots directly from my iPhone4.
This model will not slide over iPhone cases.
by
byShapeways
Type in your text and we turn it into a customized metal branding iron.
Does not include the lighter.
The lighter is a BIC World, Classic, Maxi.
Want to make your own? Download the lighter attachment part here: http://www.shapeways.com/model/121517/ Do not flip/mirror the image, ie. please upload one you want as the actual result of the branding. If you have trouble uploading image like invalid file type, please make sure the filename has extension, for example, .jpg
Does not include the lighter.
The lighter is a BIC World, Classic, Maxi.
Want to make your own? Download the lighter attachment part here: http://www.shapeways.com/model/121517/ Do not flip/mirror the image, ie. please upload one you want as the actual result of the branding. If you have trouble uploading image like invalid file type, please make sure the filename has extension, for example, .jpg
by
Pazu
Working centrifugal compressor.
Designed to fit standard Mabuchi 130 motors.
Printed and tested.
Upon receiving the item, you'll need to use a 1.8mm drill bit to drill out the center hole. This is due to limitation of the printing process that may not allow the shaft of the motor to be inserted.
Designed to fit standard Mabuchi 130 motors.
Printed and tested.
Upon receiving the item, you'll need to use a 1.8mm drill bit to drill out the center hole. This is due to limitation of the printing process that may not allow the shaft of the motor to be inserted.
by
virtox
It arrived in WSF, and it works for real :-)
Gear system based on hypotrochoid shapes.
It is printed as a 9 piece puzzle, a VERY frustrating one at that ;-)
Depending on the print batch, it might need some minor sanding to make it run properly.
Steel available on request, still untested by me.
I think steel will work but probably needs some more sanding to make it fit.
With the new pricing scheme, the steel version is no longer available.
If you want one in steel, please send me a message and we will find a way.
Gear system based on hypotrochoid shapes.
It is printed as a 9 piece puzzle, a VERY frustrating one at that ;-)
Depending on the print batch, it might need some minor sanding to make it run properly.
Steel available on request, still untested by me.
I think steel will work but probably needs some more sanding to make it fit.
With the new pricing scheme, the steel version is no longer available.
If you want one in steel, please send me a message and we will find a way.
by
Mstyle183
This is an iphone 4/4s case
Are you tired of carrying a bunch of other stuff in your pockets? do you ever wonder i wish i could just get one item that does it all? Well after a lot of research and personal pocket experience i have ben able to design a product that covers pretty much everything you will need out in the road.. Wallet, credit card holder, id holder, bussiness card holder, money clip.. and YES a bottle OPENER.. all in a tiny very compact case that will also prevent damages to your iphone.. this is like the Macgyver of the iphone cases.. this is like the swiss army of wallets.. this is like the master of money clips.. this is insanity and this case can be yours for the cheap price of $$ **prices depend on the materials.. **
This Design has been printed and tested.. You can now safely purchase it.
I have several variations of this case that fit the iphone 5 and soon the Glaxy S3. I also have variations with kickstand and earbud organizers. Check out my store and have other features like kickstand. So if you like to see other models visit shapeways.com/shops/amznfx
**If you want more space for more cards without the bulk i would suggest getting a slim wallet. They are extremely thin.
slim-minimalistic-wallet-money-clip-bottleopener
or
slim-minimalistic-wallet-with-money-clip
or for the ladies
the bikini Wallet
** metal piece for the bottle opener has been created but needs to be purchased SEPARATELY. it will only be available for purchase for those who have purchase my case. You will need to provide the order number by email for verification purposes.
Go to amznfx.com/shopping-cart
Are you tired of carrying a bunch of other stuff in your pockets? do you ever wonder i wish i could just get one item that does it all? Well after a lot of research and personal pocket experience i have ben able to design a product that covers pretty much everything you will need out in the road.. Wallet, credit card holder, id holder, bussiness card holder, money clip.. and YES a bottle OPENER.. all in a tiny very compact case that will also prevent damages to your iphone.. this is like the Macgyver of the iphone cases.. this is like the swiss army of wallets.. this is like the master of money clips.. this is insanity and this case can be yours for the cheap price of $$ **prices depend on the materials.. **
This Design has been printed and tested.. You can now safely purchase it.
I have several variations of this case that fit the iphone 5 and soon the Glaxy S3. I also have variations with kickstand and earbud organizers. Check out my store and have other features like kickstand. So if you like to see other models visit shapeways.com/shops/amznfx
**If you want more space for more cards without the bulk i would suggest getting a slim wallet. They are extremely thin.
slim-minimalistic-wallet-money-clip-bottleopener
or
slim-minimalistic-wallet-with-money-clip
or for the ladies
the bikini Wallet
** metal piece for the bottle opener has been created but needs to be purchased SEPARATELY. it will only be available for purchase for those who have purchase my case. You will need to provide the order number by email for verification purposes.
Go to amznfx.com/shopping-cart
by
spruce
Many photographers lose there lenscap, especially me.
So it was time to solve this problem.
With this cap holder you just click your lenscap in and are ready to go.
This model is specially added to my shop for people who can't find there size.
So please make sure that your size isn't available in my shop before purchase this one.
Use the shapeways personalize option to send my your requested diameter.
So it was time to solve this problem.
With this cap holder you just click your lenscap in and are ready to go.
This model is specially added to my shop for people who can't find there size.
So please make sure that your size isn't available in my shop before purchase this one.
Use the shapeways personalize option to send my your requested diameter.
by
noesis
The CardCase is now customizable! See Below
The CardCase for the IPhone 4 does what other card carrying IPhone cases can do and then some!
The sleek, patent pending, snap-on case not only protects your IPhone, but can also replaces your wallet or current business card holder and the integrated card slot on the side allows you to use any available card as an instant stand in portrait or landscape mode! Perfect for watching movies on the go, Facetime chatting, or using your IPhone as an alarm clock!
The CardCase can comfortably hold 2 credit or ID cards, or 4-5 business cards, and works perfectly with either the AT&T or Verizon IPhone versions.
And the CardCase is now customizable! When ordering you can change the side text to anything you'd like up to 15 characters (company name, twitter username, real name etc.) you can also choose the text orientation and alignment.
Designed by Noesis Design Lab and manufactured by Shapeways, this durable nylon polyamide case has a unique look and grippy feel to help keep your IPhone (and cards) safe.
The case is shipped worldwide directly from Shapeways.
Available in a multitude of colors If you don't specify a color, the default is white
The CardCase for the IPhone 4 does what other card carrying IPhone cases can do and then some!
The sleek, patent pending, snap-on case not only protects your IPhone, but can also replaces your wallet or current business card holder and the integrated card slot on the side allows you to use any available card as an instant stand in portrait or landscape mode! Perfect for watching movies on the go, Facetime chatting, or using your IPhone as an alarm clock!
The CardCase can comfortably hold 2 credit or ID cards, or 4-5 business cards, and works perfectly with either the AT&T or Verizon IPhone versions.
And the CardCase is now customizable! When ordering you can change the side text to anything you'd like up to 15 characters (company name, twitter username, real name etc.) you can also choose the text orientation and alignment.
Designed by Noesis Design Lab and manufactured by Shapeways, this durable nylon polyamide case has a unique look and grippy feel to help keep your IPhone (and cards) safe.
The case is shipped worldwide directly from Shapeways.
Available in a multitude of colors If you don't specify a color, the default is white
by
RemivanOers
CLIP-IT for iPhone
Your charge buddy on the go.
Clip-it for iPhone converts your Euro iPhone charger to a wall dock; making sure that you can easily charge your phone at every wall socket. Unfurnished rooms, hotels and conference rooms are no longer a problem.
Clip-it lets you wind the usb cable easily around your charger while taking it with you.
Clip-it makes use of your existing Apple Dock Connector to USB Cable. Simply snap it in and lock the cable at the bottom. Clip-it is perfectly engineered to hold the latest two generations of original 30 pin Apple charging cables.
Clip-it is designed for the iPhone 4 & iPhone 4S and the included Apple USB Power Adapter (European version).
After all the excitement, an US version of Clip-it is available here!
Clip-it is manufactured by innovative 3D-printing in tough but lightweight polyamide. The surface has a fine texture. The product will be shipped in basic Shapeways packaging. Some powder residue from the 3D-printing process may be found on the product itself; if this is the case, it should be easy to clean off with small tooth sticks & brushes. When you ordered Clip-it in colour it might be wise to clean it with water under the tap, so the dyeing pigments that might still be on the product don’t colour your white Apple gadgets. For further information & support contact the Shapeways customer service.
Your charge buddy on the go.
Clip-it for iPhone converts your Euro iPhone charger to a wall dock; making sure that you can easily charge your phone at every wall socket. Unfurnished rooms, hotels and conference rooms are no longer a problem.
Clip-it lets you wind the usb cable easily around your charger while taking it with you.
Clip-it makes use of your existing Apple Dock Connector to USB Cable. Simply snap it in and lock the cable at the bottom. Clip-it is perfectly engineered to hold the latest two generations of original 30 pin Apple charging cables.
Clip-it is designed for the iPhone 4 & iPhone 4S and the included Apple USB Power Adapter (European version).
After all the excitement, an US version of Clip-it is available here!
Clip-it is manufactured by innovative 3D-printing in tough but lightweight polyamide. The surface has a fine texture. The product will be shipped in basic Shapeways packaging. Some powder residue from the 3D-printing process may be found on the product itself; if this is the case, it should be easy to clean off with small tooth sticks & brushes. When you ordered Clip-it in colour it might be wise to clean it with water under the tap, so the dyeing pigments that might still be on the product don’t colour your white Apple gadgets. For further information & support contact the Shapeways customer service.
by
IHeartEngineering
The part allows you to mount the Parallax Ping))) sensor on the Hitec HS-325HB Servo. It has been optimized for Shapeways printing with the Grey Robust material.
The activity light and connector pin outs are visible.
This part will require drilling and fasteners. Two M3x5mm and two M2x6mm screws are suggested. If you don''t have the necessary taps you can use nuts.
YouTube assembly Video is available here. http://www.youtube.com/watch?v=h5oXFVhrQr8
The activity light and connector pin outs are visible.
This part will require drilling and fasteners. Two M3x5mm and two M2x6mm screws are suggested. If you don''t have the necessary taps you can use nuts.
YouTube assembly Video is available here. http://www.youtube.com/watch?v=h5oXFVhrQr8
