thatjohnkydd

by DavidAlan

This is a ring I created based on the one worn by Hal Jordan of the Green Lantern Corps. This version has a smaller face for a subtle look and feel. Choose your size from the list below and it will be added to your cart. You can select your preferred material in the cart before checkout.

Size 15

With the Shapeways Print-on-Demand service, you can order this ring in any size, in any material, at any time. Please note that, with the exception of the Full Color Sandstone material, the color, look, and feel of the ring is defined by the material you choose, not the model image.

This ring will be produced and delivered through Shapeways and it’s partners.

For questions regarding your order, please contact Shapeways through their contact page at shapeways.com/contact.

For questions regarding the design of this, or any of my other rings and models, feel free to send me a private message. Also, if you have any ideas for new rings that you would like to see me design, please let me know.

Green Lantern, Hal Jordan, and all related marks are trademarks of Warner Bros. and DC Comics.

(15)

From: $49.99

Green Lantern Silver Age Ring (Small)

in Stainless Steel

by DavidAlan

This is a ring I created based on the one worn by Hal Jordan of the Green Lantern Corps during the Silver Age of comics. This version has a smaller face for a subtle look and feel. Choose your size from the list below and it will be added to your cart. You can select your preferred material in the cart before checkout.

(10)

From: $49.99

Red Lantern Atrocitus Ring (Small)

in Stainless Steel

by DavidAlan

This is a ring I created based on the one worn by Atrocitus, founder of the Red Lantern Corps. This version has a smaller face for a subtle look and feel. Choose your size from the list below and it will be added to your cart. You can select your preferred material in the cart before checkout.

Size 15

With the Shapeways Print-on-Demand service, you can order this ring in any size, in any material, at any time. Please note that, with the exception of the Full Color Sandstone material, the color, look, and feel of the ring is defined by the material you choose, not the model image.

This ring will be produced and delivered through Shapeways and it’s partners.

For questions regarding your order, please contact Shapeways through their contact page at shapeways.com/contact.

For questions regarding the design of this, or any of my other rings and models, feel free to send me a private message. Also, if you have any ideas for new rings that you would like to see me design, please let me know.

Green Lantern, Red Lantern, Atrocitus, and all related marks are trademarks of Warner Bros. and DC Comics.

(9)

From: $49.99

Zheng3 Penny Ballista

in White Strong & Flexible

by zheng3

This ballista will easily launch a U.S. Penny across a cubicle farm, but most people use it to play Seej.

Seej is an Open Source tabletop wargame based around 3D printing. Rules and more information are available at www.s33j.net

If you'd like start playing Seej, there's a Seej Starter Set available on Shapeways, too. You'll need some extra bloxen", or possibly a whole lotta bloxen to really make a go of it. You'll want some flags, too. Construction is really simple! Needlenose pliers are recommended, but not strictly necessary.

You'll need two elastic bands to complete this ballista. Tie a single band through the bore on one of the two D-shaped locking keys. Repeat the process with the other locking key.

Feed the end of one band through the rectangular bore on the ballista's left post. Insert the tenons of the locking key into the square mortises on the post to lock the band in place. You'll be tempted to repeat the process with the other side, but don't give in. It will save you precious minutes of frustration.

Unlike the Zheng3 Penny Catapult, these locking keys should be a snug fit. If some settling of the plastic during printing has made the mortises too small, trim the tenons a bit with your blade of choice.

Center the nock on the knot that connects the two rubber bands. Make sure that the penny's cradle is facing forward.

Feed the end of the band that's been locked down through the rectangular bore on the nock. Tie the free end of the band to the second band. Now feed the free end of the second band through the outside of the rectangular bore on the right post and loop it through the second locking key.

The nock has a wee nub on its underside. Slide this nub into the ballista's firing groove; it will improve accuracy.

Load a penny into the nock, pull it back, and fire away. Be safe! Wear eye protection!

Be sure to check Zheng3.com for updates, or follow Zheng3 on Twitter.

(1)

From: $59.99

Hatak

in White Strong & Flexible

by EpytronOmega

Here is my rendition of the Hatak from Stargate SG-1. I did not create the design, merely made a copy of it thanks to several pictures from the model created by the original crew. Copyright MGM for the design

(3)

From: $17.99

New Class of Dice - Spring-loaded Icodie

in White Strong & Flexible Polished

by opresco

The die's faces are supported by springs meeting in its center.
Printed and tested OK
Copyright ©2011 Ovidiu Opresco

(4)

From: $16.95

Yellow Lantern Arkillo Ring (Small)

in Stainless Steel

by DavidAlan

This is a ring I created based on the one worn by Arkillo, second in command of the Yellow Lantern Sinestro Corps. This version has a smaller face for a subtle look and feel. Choose your size from the list below and it will be added to your cart. You can select your preferred material in the cart before checkout.

Size 15

With the Shapeways Print-on-Demand service, you can order this ring in any size, in any material, at any time. Please note that, with the exception of the Full Color Sandstone material, the color, look, and feel of the ring is defined by the material you choose, not the model image.

This ring will be produced and delivered through Shapeways and it’s partners.

For questions regarding your order, please contact Shapeways through their contact page at shapeways.com/contact.

For questions regarding the design of this, or any of my other rings and models, feel free to send me a private message. Also, if you have any ideas for new rings that you would like to see me design, please let me know.

Green Lantern, Yellow Lantern, Sinestro Corps, Arkillo, and all related marks are trademarks of Warner Bros. and DC Comics.

(10)

From: $49.99