by
virtox
Accused of being fake, witchcraft and simply impossible..
This kinetic sculpture is inspired by the unlimited freedom of 3d printing,
it wobbles and turns with a slight movement of the hand.
Now give it a good spin or puff of air and it erupts in erratic and wild behavior.
This is the 5cm / 2" version, see the Gyro the Forms section for other shapes and sizes.
Corner stand available separately, or get the complete set below!
NEW!
Now also available as a pendant/keyfob!
In both Extra small and Small
Instructions
It is composed of four concentric cubes, each one spinning around a different axis.
The model needs some minor assembly:
Each inner cube has two knobs which need to be placed into the corresponding clamps in the parent cube. It's easiest to start with the inner most and continue outward.
And then... spin it away !
Notes
Do not be alarmed if your cube will not run smoothly at first!
Because of minor variations as a result of the printing process,
some need to wear in a little but will loosen up very quickly.
In the example video I am blowing on it to make it move, it's that smooth.
Be a little careful with (the assembly of) the Alumide version as this material is slightly less flexible/robust than the Strong & Flexible materials.
Get a complete set.
A default set consists of an Alumide Gyro the Cube and a White stand, you can change the materials in your cart later.
+ 
This kinetic sculpture is inspired by the unlimited freedom of 3d printing,
it wobbles and turns with a slight movement of the hand.
Now give it a good spin or puff of air and it erupts in erratic and wild behavior.
This is the 5cm / 2" version, see the Gyro the Forms section for other shapes and sizes.
Corner stand available separately, or get the complete set below!
NEW!
Now also available as a pendant/keyfob!
In both Extra small and Small
Instructions
It is composed of four concentric cubes, each one spinning around a different axis.
The model needs some minor assembly:
Each inner cube has two knobs which need to be placed into the corresponding clamps in the parent cube. It's easiest to start with the inner most and continue outward.
And then... spin it away !
Notes
Do not be alarmed if your cube will not run smoothly at first!
Because of minor variations as a result of the printing process,
some need to wear in a little but will loosen up very quickly.
In the example video I am blowing on it to make it move, it's that smooth.
Be a little careful with (the assembly of) the Alumide version as this material is slightly less flexible/robust than the Strong & Flexible materials.
Get a complete set.
A default set consists of an Alumide Gyro the Cube and a White stand, you can change the materials in your cart later.
+ 
by
roessnakhan
A replica of Cobb's totem from the film "Inception". As a below review has noted, and from my own version, the top works very well, and spins upwards of 90 seconds before toppling. You just might be in a dream.
by
joabaldwin
This is a mobius strip of Level 1 or Super Mario Bros. The whole level is wrapped around itself in a single surface, and poor Mario begins and ends at the same spot every time :(
All the elements from the level are there: every mushroom, turtle, cloud and star. They are all carved out of the surface at different heights, which looks fantastic when you have a light coming from the side, and each block casts a shadow.
It's a great piece to have on your desk, or to hang from a string to let it spin around.
All the elements from the level are there: every mushroom, turtle, cloud and star. They are all carved out of the surface at different heights, which looks fantastic when you have a light coming from the side, and each block casts a shadow.
It's a great piece to have on your desk, or to hang from a string to let it spin around.
by
TheoJansen
[Note: This propeller propulsion add-on does not include a 3D printed Strandbeest, which should be bought seperately! This propeller does not fit the Ondula version!]
Theo Jansen’s 3D printed Strandbeest continues to evolve with the addition of a Propeller Propulsion system! The 3D printed Strandbeests can now walk autonomously, powered by the wind, just like Theo's full-scale Strandbeests. The new propeller add-on gives new and existing owners of these kinetic sculptures a new way to set them in motion!
The propeller addition is available as a separate kit, which can be mounted on the 3D printed Strandbeests. The propeller is compatible with the various evolutions of the Strandbeest, so existing owners of the “AGP” 5 and 7 model Strandbeests can use it as well. Consisting of 5 main parts, it can be mounted on the Strandbeest body in a few simple steps.
Also see our videos of the Strandbeest Propulsion in action, and the video with mounting instructions.
The 3D printed Strandbeest is sold separately.
A few tips to consider:
- Please look at our instruction video on mounting the Propeller Propulsion add-on, here.
- After mounting the Propeller Propulsion add-on it is best left mounted. Frequent dis-assembly can wear down the material which can result in play on the mechanism.
Theo Jansen’s 3D printed Strandbeest continues to evolve with the addition of a Propeller Propulsion system! The 3D printed Strandbeests can now walk autonomously, powered by the wind, just like Theo's full-scale Strandbeests. The new propeller add-on gives new and existing owners of these kinetic sculptures a new way to set them in motion!
The propeller addition is available as a separate kit, which can be mounted on the 3D printed Strandbeests. The propeller is compatible with the various evolutions of the Strandbeest, so existing owners of the “AGP” 5 and 7 model Strandbeests can use it as well. Consisting of 5 main parts, it can be mounted on the Strandbeest body in a few simple steps.
Also see our videos of the Strandbeest Propulsion in action, and the video with mounting instructions.
The 3D printed Strandbeest is sold separately.
A few tips to consider:
- Please look at our instruction video on mounting the Propeller Propulsion add-on, here.
- After mounting the Propeller Propulsion add-on it is best left mounted. Frequent dis-assembly can wear down the material which can result in play on the mechanism.
by
avandius
This is a 16mm to 24mm dice set modeled after the Deathly Hallows from Harry Potter.
The Black Strong & Flexible set (red background) was hand-painted using Spanish Copper and Gold rub'n'buff (sold separately).
Alumide set was dyed black and painted with silver enamel (sold separately).
The Black Strong & Flexible set (red background) was hand-painted using Spanish Copper and Gold rub'n'buff (sold separately).
Alumide set was dyed black and painted with silver enamel (sold separately).
by
joabaldwin
Low polygon Cloud Strife from Final Fantasy 7. I modeled him identical to the original low poly you see in the FF7 videogame (not the cutscenes version or fights version, but the playable, big headed one you actually control).
#####This is NOT an official model by Square Enix#####
I just made it myself since I couldn't find official merchandise with the low poly character.
The 3d print looks great, though the hair isn't as spiky as it should be, since color printing can't do such sharp points.
#####This is NOT an official model by Square Enix#####
I just made it myself since I couldn't find official merchandise with the low poly character.
The 3d print looks great, though the hair isn't as spiky as it should be, since color printing can't do such sharp points.
by
INNERLEAF
The Exoskeleton Shoe was Designed By Janina Alleyne & 3D Modelled for 3D Printing by INNER | LEAF. This full size shoe is for decorative purposes only, a wearable version is available upon request. Please email adam@inner-leaf.com.
by
Oskar_van_Deventer
Dino Cube is a classic cube design from the 1980's, designed by ...
Watch the YouTube video.
Please contact Oskar directly if you are interested in obtaining a fully colored, stickered and assembled sample of this puzzle.
Watch the YouTube video.
Please contact Oskar directly if you are interested in obtaining a fully colored, stickered and assembled sample of this puzzle.
