by
joabaldwin
This is a mobius strip of Level 1 or Super Mario Bros. The whole level is wrapped around itself in a single surface, and poor Mario begins and ends at the same spot every time :(
All the elements from the level are there: every mushroom, turtle, cloud and star. They are all carved out of the surface at different heights, which looks fantastic when you have a light coming from the side, and each block casts a shadow.
It's a great piece to have on your desk, or to hang from a string to let it spin around.
All the elements from the level are there: every mushroom, turtle, cloud and star. They are all carved out of the surface at different heights, which looks fantastic when you have a light coming from the side, and each block casts a shadow.
It's a great piece to have on your desk, or to hang from a string to let it spin around.
by
curvecreative
Nanolet
Everyone's wearing their Nano on their wrist nowadays, now you can wear it on a one part 3D printed nano bracelet.
The NANOLET simply wraps around your wrist and fits snugly up to your hand which is perfect for running and everyday use. An alternative to the plethora of nano watches that are around now.
Featured on: Mashable , Cult of Mac , Yanko Design and many more.
Suitable for medium sized wrists. Available in a range of colors
Medium is for a wrist of circumference 165mm - 185mm. The best way to measure your wrist is to wrap a piece of string around your wrist, mark it and then measure it. Maximum wrist size is 190mm.
Unboxing Video here
Click here for OTHER SIZES
Click here to visit our site
Or click here to keep up to date on Facebook
Interested in buying Nanolets in BULK at reduced price? For LARGE , MEDIUM and SMALL
by
s_f_x
Update: I am currently working on an updated version, which is more robust and uses a more conventional 3-axis design (one servo per axis). I will leave this model available for spare parts. The new model is currently being tested and should be available soon.
This is a 3-axis gyro-stabilsation gimbal for the GoPro HD Hero camera. Intended use is for aerial video and first-person view (FPV) flying.
(Picture shows all the parts - camera is not included, and this is model here is only the back cage. Check the 3D model to see it. For the complete kit you have to order the back cage, the front lid, the servo cage and the mounting arm. You will also need 3x MKS470 servos, and a 16mm x 8mm ball bearing, not shown)
Video demonstration:
Assembly and servo test
Preliminary Gyro stabilisation test
Current status:
This is still work in progress - the current version has been slightly improved from the version in the video (I strengthened some of the elastic parts and improved the balancing). The gyro control board is my own design and currently not available yet. I will post an update once it is. The IMU is my design as well, and is available here.
You are welcome to order this design now, but be aware that it's still somewhat "beta". Whatever you do with it is entirely your own risk and responsibility, I unfortunately cannot make any claims towards its usefulness, stability or safety...
I would recommend, before you put this on a flying contraption, consider using a safety string to attach the camera to the plane somehow. GoPro cameras are very robust inside their waterproof case, but not quite so robust without that protection. They don't like crashing into the ground (and trust me, I know - as is probably obvious from the picture of my camera... in all fairness, it did mostly survive...)
Assembly instructions
For the complete kit you have to order the back cage, the front lid, the servo cage and the mounting arm. The bearing at the top is a 16mm outer, 8mm inner diameter ball bearing, available from many places. Hobbyking sells those as well.
I will possibly modify the mounting bracket in the future and also offer one with a smaller bearing... this one is total overkill! :)
The servos that will fit are the MKS DS470 (available e.g. from Hobbyking). They do have a little play, but they are very smooth and by far the fastest servo I've seen in that size and price class. I'm still on the lookout for different servos that might be a bit smoother.
Assembly:
1) Press the servos onto the mounting bracket and the flexible arms of the back cage. What works quite well is to carefully push it on just a little (best to put the printed piece onto a flat surface, and gently push the servo in just a bit to align). Then use a screw (maybe with a washer to spread the force), and slowly pull the arm onto the crown. You only have to do that once, it'll be a tight, smooth fit afterwards.
Remove the servos again after this step.
2) Mount the 3 servos on the servo mounting frame. Start with the yaw servo (the vertical one in the middle).The yaw servo crown has to face downwards (might be a bit fiddly). Make sure the crown of the yaw servo is aligned with the little stub axle on the opposite side. The two roll/pitch servos have to be inserted so that the crown faces the camera (towards the flat side of the mounting arm).
3) Press the mounting bracket onto the yaw servo crown, and put in the screw to hold it in place. On the opposite side, press in the 16mm/8mm ball bearing.
4) Carefully push the disk-shaped closure knob into the cylinder at the top of the camera back cage. You might need to rotate it a bit to ease it into place
5) Push the flexible arms of the back cage onto the two roll/pitch servos, and fix with screws.
-- Update: Seems the MKS has too much gain for the yaw axis, and tends to oscillate a bit with all that weight swinging around. They are fine for the Pitch/Roll arms. I'm still looking for a small servo with high speed, smoothness and no (or little) play... Suggestions are of course welcome!!
-- The servos are still a very tight fit into the control arms and the bracket. I already made it a bit larger, but still not enough. What works quite well is to carefully push it on just a little (best to put the arms onto a flat surface, and gently push the servo in just a bit to align). Then use a screw (maybe with a washer to spread the force), and slowly pull the arm onto the crown. You only have to do that once, it'll be a tight, smooth fit afterwards.
This is a 3-axis gyro-stabilsation gimbal for the GoPro HD Hero camera. Intended use is for aerial video and first-person view (FPV) flying.
(Picture shows all the parts - camera is not included, and this is model here is only the back cage. Check the 3D model to see it. For the complete kit you have to order the back cage, the front lid, the servo cage and the mounting arm. You will also need 3x MKS470 servos, and a 16mm x 8mm ball bearing, not shown)
Video demonstration:
Assembly and servo test
Preliminary Gyro stabilisation test
Current status:
This is still work in progress - the current version has been slightly improved from the version in the video (I strengthened some of the elastic parts and improved the balancing). The gyro control board is my own design and currently not available yet. I will post an update once it is. The IMU is my design as well, and is available here.
You are welcome to order this design now, but be aware that it's still somewhat "beta". Whatever you do with it is entirely your own risk and responsibility, I unfortunately cannot make any claims towards its usefulness, stability or safety...
I would recommend, before you put this on a flying contraption, consider using a safety string to attach the camera to the plane somehow. GoPro cameras are very robust inside their waterproof case, but not quite so robust without that protection. They don't like crashing into the ground (and trust me, I know - as is probably obvious from the picture of my camera... in all fairness, it did mostly survive...)
Assembly instructions
For the complete kit you have to order the back cage, the front lid, the servo cage and the mounting arm. The bearing at the top is a 16mm outer, 8mm inner diameter ball bearing, available from many places. Hobbyking sells those as well.
I will possibly modify the mounting bracket in the future and also offer one with a smaller bearing... this one is total overkill! :)
The servos that will fit are the MKS DS470 (available e.g. from Hobbyking). They do have a little play, but they are very smooth and by far the fastest servo I've seen in that size and price class. I'm still on the lookout for different servos that might be a bit smoother.
Assembly:
1) Press the servos onto the mounting bracket and the flexible arms of the back cage. What works quite well is to carefully push it on just a little (best to put the printed piece onto a flat surface, and gently push the servo in just a bit to align). Then use a screw (maybe with a washer to spread the force), and slowly pull the arm onto the crown. You only have to do that once, it'll be a tight, smooth fit afterwards.
Remove the servos again after this step.
2) Mount the 3 servos on the servo mounting frame. Start with the yaw servo (the vertical one in the middle).The yaw servo crown has to face downwards (might be a bit fiddly). Make sure the crown of the yaw servo is aligned with the little stub axle on the opposite side. The two roll/pitch servos have to be inserted so that the crown faces the camera (towards the flat side of the mounting arm).
3) Press the mounting bracket onto the yaw servo crown, and put in the screw to hold it in place. On the opposite side, press in the 16mm/8mm ball bearing.
4) Carefully push the disk-shaped closure knob into the cylinder at the top of the camera back cage. You might need to rotate it a bit to ease it into place
5) Push the flexible arms of the back cage onto the two roll/pitch servos, and fix with screws.
-- Update: Seems the MKS has too much gain for the yaw axis, and tends to oscillate a bit with all that weight swinging around. They are fine for the Pitch/Roll arms. I'm still looking for a small servo with high speed, smoothness and no (or little) play... Suggestions are of course welcome!!
-- The servos are still a very tight fit into the control arms and the bracket. I already made it a bit larger, but still not enough. What works quite well is to carefully push it on just a little (best to put the arms onto a flat surface, and gently push the servo in just a bit to align). Then use a screw (maybe with a washer to spread the force), and slowly pull the arm onto the crown. You only have to do that once, it'll be a tight, smooth fit afterwards.
by
fakebusker83
Version 1.0
Edit: The world famous Transformers customizer Encline has put up a review of this pair of Optimus Prime's hands! In the video he shows the assembly process, installation, and he finally showcases how well the hands worked, holding weapons and giving various poses! Again, I am very honoured to have my designs reviewed in such an awesome manner. Link is located below!
A pair of hands for ROTF Leader class Optimus Prime! These hands are fully articulated with ball joints on the fingers, thumbs and wrists! Also, they are capable of holding 5mm peg mechtech weapons as well as his original rifle!
Recommended material: Strong Flexible
Edit: The world famous Transformers customizer Encline has put up a review of this pair of Optimus Prime's hands! In the video he shows the assembly process, installation, and he finally showcases how well the hands worked, holding weapons and giving various poses! Again, I am very honoured to have my designs reviewed in such an awesome manner. Link is located below!
A pair of hands for ROTF Leader class Optimus Prime! These hands are fully articulated with ball joints on the fingers, thumbs and wrists! Also, they are capable of holding 5mm peg mechtech weapons as well as his original rifle!
Recommended material: Strong Flexible
by
fakebusker83
Just added: a photo of an awesome leader Starscream custom using these hands, done by my good friend Encline!
Note: I have tested these hands in both Strong Flexible and Detail material, and I conclude SF is the better alternative as it is much hardier and is able to stand up to the wear and tear of the joints. Detail material is disappointingly unable to do so, and the joints are too loose for comfort. For better surface detail, I highly recommend ordering the hands in White Strong Flexible Polished!
A pair of posable hands for the Revenge of the Fallen Leader Starscream figure!
Each order comes with 2 hands with interchangeable core, giving customizers the freedom to mount the core with a 5mm socket to allow arming of compatible weapons, or the lack of a socket for an aesthetically pleasing appearance.
Each hand possesses 3 posable fingers on ball-joints, bending in 2 places, and 2 thumbs also mounted on ball joints.
The wrist too, is on a ball joint, allowing for dynamic poses on a already awesome figure.
Due to the nature of the installation, this model is for experienced customizers only. You need a dremel, cutting knife and a strong epoxy sculpt. These are for removing the existing hands and installing the wrist ball-joints in their place.
Flickr set is here.
TFW2005 thread is here. (Includes assembly instructions)
Note: I have tested these hands in both Strong Flexible and Detail material, and I conclude SF is the better alternative as it is much hardier and is able to stand up to the wear and tear of the joints. Detail material is disappointingly unable to do so, and the joints are too loose for comfort. For better surface detail, I highly recommend ordering the hands in White Strong Flexible Polished!
A pair of posable hands for the Revenge of the Fallen Leader Starscream figure!
Each order comes with 2 hands with interchangeable core, giving customizers the freedom to mount the core with a 5mm socket to allow arming of compatible weapons, or the lack of a socket for an aesthetically pleasing appearance.
Each hand possesses 3 posable fingers on ball-joints, bending in 2 places, and 2 thumbs also mounted on ball joints.
The wrist too, is on a ball joint, allowing for dynamic poses on a already awesome figure.
Due to the nature of the installation, this model is for experienced customizers only. You need a dremel, cutting knife and a strong epoxy sculpt. These are for removing the existing hands and installing the wrist ball-joints in their place.
Flickr set is here.
TFW2005 thread is here. (Includes assembly instructions)
by
fakebusker83
Version 1.6
A little robotic cat that transforms into a cyber cassette that fits into the deluxe War for Cybertron Soundwave figure! It comes with 2 detachable missile accessories.
Radicon thread here.
Flickr thread here.
A little robotic cat that transforms into a cyber cassette that fits into the deluxe War for Cybertron Soundwave figure! It comes with 2 detachable missile accessories.
Radicon thread here.
Flickr thread here.
by
fakebusker83
Version 2.0
A pair of posable hands for the Dark of the Moon Leader class Ironhide figure! Each finger is double-jointed, the wrists and thumbs are also ball-jointed, and the hands still fit behind the windscreen in his alt mode!
Not for casual collectors. You will need a dremel and some skill to install these hands.
I recommend these to be printed in Strong Flexible material for maximum reliability.
Radicon thread here. (With installation instructions)
Flickr gallery here.
A pair of posable hands for the Dark of the Moon Leader class Ironhide figure! Each finger is double-jointed, the wrists and thumbs are also ball-jointed, and the hands still fit behind the windscreen in his alt mode!
Not for casual collectors. You will need a dremel and some skill to install these hands.
I recommend these to be printed in Strong Flexible material for maximum reliability.
Radicon thread here. (With installation instructions)
Flickr gallery here.
by
joabaldwin
Half Life 2 meets Portal. Gordon Freeman and Alyx Vance's best friend, DOG, contemplating the beauty of his new toy, a companion cube. What else could you possibly want? Oh, that's right, Half-Life 2 Episode 3 would be nice...
Gabe, are you listening?
This uses the original texture maps from the game, you can even see the Lambda Half Life logo on DOG's back.
It wasn't easy! I had to remap all the textures manually, and fix all the geometry to make it printable and thick enough to support the weight. I also made most large pieces hollow, but you won't notice that at all (except in the reduced price this provided).
Gabe, are you listening?
This uses the original texture maps from the game, you can even see the Lambda Half Life logo on DOG's back.
It wasn't easy! I had to remap all the textures manually, and fix all the geometry to make it printable and thick enough to support the weight. I also made most large pieces hollow, but you won't notice that at all (except in the reduced price this provided).
by
fakebusker83
Version 4.5: Edited for peg locks to be sturdier.
Finally, after a long wait and 4(!) iterations of design, here is the release version of the much anticipated Snitch! The Snitch is a robotic avian that transforms into a cyber-cassette mode which stores in the War for Cybertron deluxe Soundwave figure!
This version is successfully tested on WSF and FUD.
Radicon thread here
Flickr gallery here.
Finally, after a long wait and 4(!) iterations of design, here is the release version of the much anticipated Snitch! The Snitch is a robotic avian that transforms into a cyber-cassette mode which stores in the War for Cybertron deluxe Soundwave figure!
This version is successfully tested on WSF and FUD.
Radicon thread here
Flickr gallery here.
by
VF5SS
Part designed by Sanjeev for use with Kanzen Henkei Fighter Variable (all types). Comes with two complete hinges. 4 mm type. Uses existing screws and pins from stock toy. Can also use same size metal tacks for hinge joint.
Visit Sanjeev's toy studio at http://brownnoize.blogspot.com/
by
fakebusker83
Version 1.5
A pair of posable hands for use with the ROTF leader Optimus Prime figure! The wrists, thumbs and all fingers are ball-jointed. Additionally, the back of each hand unfolds to form a deadly knuckle duster!
This design is recommended in Strong Flexible material.
TFW Radicon thread here.
Flickr gallery here.
A pair of posable hands for use with the ROTF leader Optimus Prime figure! The wrists, thumbs and all fingers are ball-jointed. Additionally, the back of each hand unfolds to form a deadly knuckle duster!
This design is recommended in Strong Flexible material.
TFW Radicon thread here.
Flickr gallery here.
by
richgain
This cube really is something quite special.
About a year ago, after seeing the Transformers movie, I was inspired, by the behaviour of the alien technology in the AllSpark cube, to try and design a puzzle that could expand equally in all directions. To make things even harder, I wanted each piece to be locked in place by the preceding move.
After many prototypes I finally succeeded in creating this unique sculpture consisting of six parts.
The first stage in solving the puzzle involves discovering how the pieces fit together in the expanded configuration. (One of these moves includes a rotation, which makes it much harder to crack by computer!)
The second stage is to collapse the expanded cube down to the smaller cube by pressing each of the faces in the correct sequence.
The name of the puzzle comes from a (now obsolete) alternative to the Big Bang Theory proposed by Fred Hoyle. I like the fact that from its expanded, steady state the cube can either collapse inwards or explode outwards.
© Richard Gain 2008
About a year ago, after seeing the Transformers movie, I was inspired, by the behaviour of the alien technology in the AllSpark cube, to try and design a puzzle that could expand equally in all directions. To make things even harder, I wanted each piece to be locked in place by the preceding move.
After many prototypes I finally succeeded in creating this unique sculpture consisting of six parts.
The first stage in solving the puzzle involves discovering how the pieces fit together in the expanded configuration. (One of these moves includes a rotation, which makes it much harder to crack by computer!)
The second stage is to collapse the expanded cube down to the smaller cube by pressing each of the faces in the correct sequence.
The name of the puzzle comes from a (now obsolete) alternative to the Big Bang Theory proposed by Fred Hoyle. I like the fact that from its expanded, steady state the cube can either collapse inwards or explode outwards.
© Richard Gain 2008
by
fakebusker83
Version 2.0
This is an update for the pair of hands I did for ROTF Leader class Optimus Prime. Much time has been invested in making them look as movie accurate as possible. These hands, like their predecessors, are fully articulated with ball joints on the fingers, thumbs and wrists and they are capable of holding 5mm peg mechtech weapons as well as his original rifle!
Recommended materials: Strong Flexible
This is an update for the pair of hands I did for ROTF Leader class Optimus Prime. Much time has been invested in making them look as movie accurate as possible. These hands, like their predecessors, are fully articulated with ball joints on the fingers, thumbs and wrists and they are capable of holding 5mm peg mechtech weapons as well as his original rifle!
Recommended materials: Strong Flexible
by
fakebusker83
In response to requests from friends and supporters, I did a revised version of my posable hands for the DOTM leader Sentinel Prime figure, this time to be much more movie accurate and with even more detail!
Each hand is articulated at the wrist with a ball joint. The fingers each are double jointed, and even the thumbs are on ball joints. The leader's hands are big enough for me to design it such that it can hold weapons without relying on the tension of the finger joints, so you can pose them in many different ways, with many different weapons. Transformation is very much possible, I made sure of that (yay!). Just make sure the fingers are arranged properly, kinda similar to how the original fingers were. IssuesThe test sample has a loose wrist ball-joint. This issue is not fixed as I used the same measurements as my other hands. Those hands came out with tight joints so it beats me why this sample was loose. Use super glue to tighten if necessary. As the joints are all designed to be sturdy and the pieces are kinda chunky, I will not recommend ordering them in Detail material or Frosted Ultra Detail material as they will most likely break under that pressure. However, I still will make these materials available for those who are picky about their surface detail. Buyer beware!
TFW2005 thread here. (Includes assembly instructions)
Flickr gallery here.
Each hand is articulated at the wrist with a ball joint. The fingers each are double jointed, and even the thumbs are on ball joints. The leader's hands are big enough for me to design it such that it can hold weapons without relying on the tension of the finger joints, so you can pose them in many different ways, with many different weapons. Transformation is very much possible, I made sure of that (yay!). Just make sure the fingers are arranged properly, kinda similar to how the original fingers were. IssuesThe test sample has a loose wrist ball-joint. This issue is not fixed as I used the same measurements as my other hands. Those hands came out with tight joints so it beats me why this sample was loose. Use super glue to tighten if necessary. As the joints are all designed to be sturdy and the pieces are kinda chunky, I will not recommend ordering them in Detail material or Frosted Ultra Detail material as they will most likely break under that pressure. However, I still will make these materials available for those who are picky about their surface detail. Buyer beware!
TFW2005 thread here. (Includes assembly instructions)
Flickr gallery here.
by
Drawn-SteelHero
Detailed sniper assault rifle with flip-down bipod converts into a 56mm robot action figure with 9 points of articulation.
Gun mode comes with a choice of three handles, any one of which can be fit onto the figure during assembly (and since they are attached via a simple clip-in hinge, you can keep the others handy and swap them later if you choose). Option 1 is a standard 5mm post, which is compatible with any figure bearing a 5mm peg hole. Options 2 and 3 are modified versions of the post, which can still be used by figures with 5mm peg holes, but also have built-in clips which allow them to clip onto any 3mm diameter rail. One version has the opening of the clip positioned parallel to the length of the gun, the other perpendicular.
Supplied as a 18-piece kit. Finishing (painting/dyeing) required, alternatively can be purchased in one of the available pre-dyed colours .
Assembly and conversion instructions available HERE.
Gun mode comes with a choice of three handles, any one of which can be fit onto the figure during assembly (and since they are attached via a simple clip-in hinge, you can keep the others handy and swap them later if you choose). Option 1 is a standard 5mm post, which is compatible with any figure bearing a 5mm peg hole. Options 2 and 3 are modified versions of the post, which can still be used by figures with 5mm peg holes, but also have built-in clips which allow them to clip onto any 3mm diameter rail. One version has the opening of the clip positioned parallel to the length of the gun, the other perpendicular.
Supplied as a 18-piece kit. Finishing (painting/dyeing) required, alternatively can be purchased in one of the available pre-dyed colours .
Assembly and conversion instructions available HERE.
by
Drawn-SteelHero
Fearsome-looking machine gun converts into a 56mm robot action figure with 10 points of articulation.
Gun mode's handle is a 5mm diameter peg, making it compatible with many larger robot action figures.
Supplied as a 14-piece kit. Finishing (painting/dyeing) required, alternatively can be purchased in one of the available pre-dyed colours.
Assembly instructions available at:
http://www.shapeways.com/forum/index.php?t=msg&goto=21214&#msg_21214
If you purchase Salvo, in any material, I'd love to see your results in the "It Arrived" forum!
Gun mode's handle is a 5mm diameter peg, making it compatible with many larger robot action figures.
Supplied as a 14-piece kit. Finishing (painting/dyeing) required, alternatively can be purchased in one of the available pre-dyed colours.
Assembly instructions available at:
http://www.shapeways.com/forum/index.php?t=msg&goto=21214&#msg_21214
If you purchase Salvo, in any material, I'd love to see your results in the "It Arrived" forum!
by
fakebusker83
Version 3.0
"It's Seismus. The 'S' is silent."
Seismus hails from the Smashmasters, a clan of alien robots who eschews the cowardly methods of ranged combat in preference of going into the thick of things and smashing their enemies. Obviously, no matter how good their legendary close combat skills are, many of them are unable to survive the realities of war, and many of them perished to the guns they hated so much.
There are few who remain, but those with the fortune of having one as an ally will discover they still seethe with uncontrollable rage and raw power.
Seismus comes armed with a spear, shield and a mini-Seismus hammer, and he can be transformed into a lethal war hammer. The shaft of the spear, or the handle of the hammer is 3mm in diameter, but he comes with 2 conversion sheaths to allow larger figures with 5mm peg fists to be able to hold him.
This model is tested in White Strong Flexible.
Flickr gallery here.
TFW2005 thread here.
"It's Seismus. The 'S' is silent."
Seismus hails from the Smashmasters, a clan of alien robots who eschews the cowardly methods of ranged combat in preference of going into the thick of things and smashing their enemies. Obviously, no matter how good their legendary close combat skills are, many of them are unable to survive the realities of war, and many of them perished to the guns they hated so much.
There are few who remain, but those with the fortune of having one as an ally will discover they still seethe with uncontrollable rage and raw power.
Seismus comes armed with a spear, shield and a mini-Seismus hammer, and he can be transformed into a lethal war hammer. The shaft of the spear, or the handle of the hammer is 3mm in diameter, but he comes with 2 conversion sheaths to allow larger figures with 5mm peg fists to be able to hold him.
This model is tested in White Strong Flexible.
Flickr gallery here.
TFW2005 thread here.
by
Drawn-SteelHero
Powerful hand-held thermal cannon converts into a 56mm robot action figure with 9 points of articulation.
Gun mode comes with a choice of two handles, either of which can be glued in to the mounting point on the figure's back. Option 1 is a standard 5mm post, which is compatible with any figure bearing a 5mm peg hole. Option 2 is a modified version of the post, which can still be used by figures with 5mm peg holes, but also has a built-in clip which allows it to clip onto any 3mm diameter rail.
Supplied as a 16-piece kit. Finishing (painting/dyeing) required, alternatively can be purchased in one of the available pre-dyed colours.
Assembly instructions coming soon...
Gun mode comes with a choice of two handles, either of which can be glued in to the mounting point on the figure's back. Option 1 is a standard 5mm post, which is compatible with any figure bearing a 5mm peg hole. Option 2 is a modified version of the post, which can still be used by figures with 5mm peg holes, but also has a built-in clip which allows it to clip onto any 3mm diameter rail.
Supplied as a 16-piece kit. Finishing (painting/dyeing) required, alternatively can be purchased in one of the available pre-dyed colours.
Assembly instructions coming soon...
by
fakebusker83
Version 1.5
A pair of claw weapons for the HFTD Tomahawk figure! This design is inspired by the appearance of the Wrecker Whirl in the IDW comics, and are meant to emulate his 4 fingered claw design.
Each finger-claw has 2 ball joints and are mounted on a wrist section which can rotate 360d as well.
Because of the fist-sheath that is supposed to hide the original hands of the figure, these claws are not suitable for all figures. As a rough guideline, the width of the figure's forearm should be equal to or narrower than 12mm. Also, the figure should be able to hold a 5mm peg handle.
A pair of claw weapons for the HFTD Tomahawk figure! This design is inspired by the appearance of the Wrecker Whirl in the IDW comics, and are meant to emulate his 4 fingered claw design.
Each finger-claw has 2 ball joints and are mounted on a wrist section which can rotate 360d as well.
Because of the fist-sheath that is supposed to hide the original hands of the figure, these claws are not suitable for all figures. As a rough guideline, the width of the figure's forearm should be equal to or narrower than 12mm. Also, the figure should be able to hold a 5mm peg handle.
by
fakebusker83
Version 2.5
A design for DOTM Megatron's right hand built to be used for DOTM leader Sentinel Prime figure! This hand design is made famous by Limewire's custom leader class DOTM Megatron and is now made available to you!
A design for DOTM Megatron's right hand built to be used for DOTM leader Sentinel Prime figure! This hand design is made famous by Limewire's custom leader class DOTM Megatron and is now made available to you!
by
fakebusker83
Version 2.0
This pair of hands are specially designed for the Human Alliance Bumblebee figure! Not only are they extremely posable, the right arm cannon feature of the figure is preserved and everything fits nicely in alt mode!
TFW2005 thread here (with assembly instructions.)
This pair of hands are specially designed for the Human Alliance Bumblebee figure! Not only are they extremely posable, the right arm cannon feature of the figure is preserved and everything fits nicely in alt mode!
TFW2005 thread here (with assembly instructions.)
by
Automaster
AVAILABLE NOW!!
Here is Seeker Missile 2.0. Designed to be more in scale with your Seeker's arm than the store bought clunky ones, and it has added detail. This gives you, the fan, the choice of weapon length for your Seeker Army.
For smoothest results order in White Strong & Flexible Polished. Perfect for Classics/Henkei/Universe/Generations Starscream, Skywarp, Thundercracker, Ramjet, Dirge, Thrust, and Acid Storm.
I've personally designed these missiles for your Seeker army. These are sleek and lean compared to the clunky store bought versions. Looks great printed in white, black, or gray strong & flexible. For a super smooth store-like finish order in White, Strong & Flexible Polished and paint accordingly.
If you've ordered my products and are really happy with them, please take a minute to leave me feedback at tfw2005.com:
http://www.tfw2005.com/boards/commissioner-listing-feedback/476321-automaster-customs-shapeways-tf-accessories.html
I appreciate your business and your feedback will help me make more and better products.
Here is Seeker Missile 2.0. Designed to be more in scale with your Seeker's arm than the store bought clunky ones, and it has added detail. This gives you, the fan, the choice of weapon length for your Seeker Army.
For smoothest results order in White Strong & Flexible Polished. Perfect for Classics/Henkei/Universe/Generations Starscream, Skywarp, Thundercracker, Ramjet, Dirge, Thrust, and Acid Storm.
I've personally designed these missiles for your Seeker army. These are sleek and lean compared to the clunky store bought versions. Looks great printed in white, black, or gray strong & flexible. For a super smooth store-like finish order in White, Strong & Flexible Polished and paint accordingly.
If you've ordered my products and are really happy with them, please take a minute to leave me feedback at tfw2005.com:
http://www.tfw2005.com/boards/commissioner-listing-feedback/476321-automaster-customs-shapeways-tf-accessories.html
I appreciate your business and your feedback will help me make more and better products.
by
fakebusker83
A pair of wrists, hands and add-on accessories for the ROTF voyager Starscream figure! Every finger is posable on ball joints, and the wrists are double-jointed for maximum posability!
These hands can collapse neatly in jet mode for a more satisfying, streamlined appearance. Additionally, the add-on weapons can be mounted on the underwing hardpoints. There are so many ways to customise this set!
Flickr set is here.
TFW2005 thread is here. (Includes assembly instructions)
These hands can collapse neatly in jet mode for a more satisfying, streamlined appearance. Additionally, the add-on weapons can be mounted on the underwing hardpoints. There are so many ways to customise this set!
Flickr set is here.
TFW2005 thread is here. (Includes assembly instructions)
by
Kitty
The inner workings for F-toys AT-AT scale 1:144 foot.
material, white or black detail
requires removing inside support and toes from original model
The pivotrods (0.5mm diameter brass recommended) are not included
this is just 1 foot, you need 4 of them
material, white or black detail
requires removing inside support and toes from original model
The pivotrods (0.5mm diameter brass recommended) are not included
this is just 1 foot, you need 4 of them
by
Drawn-SteelHero
Powerful hand-held acid blaster rifle converts into a 56mm robot action figure with 9 points of articulation.
Gun mode comes with a choice of three handles, any of which can be glued in to the mounting point on the figure's back.
Option 1 is a standard 5mm post, which is compatible with any figure bearing a 5mm peg hole.
Option 2 is a modified version of the post, which can still be used by figures with 5mm peg holes, but also has a built-in clip which allows it to clip onto any 3mm diameter rail.
Option 3 is a two-stage post, which like Option 1, can fit into any 5mm peg hole, but also has a narrowed end allowing it to be used by figures with 4mm diameter peg holes.
Newly redesigned hands are able to hold or clip onto any 3mm diameter rod.
A new hinge design means this figure is now available to be printed in the Detail materials as well as WSF. However, WSF Polished is recommended for the best combination of durability and smoothness.
Supplied as a 14-piece kit. Finishing (painting/dyeing) required, alternatively can be purchased in one of the available pre-dyed colours.
Assembly instructions coming soon...
Gun mode comes with a choice of three handles, any of which can be glued in to the mounting point on the figure's back.
Option 1 is a standard 5mm post, which is compatible with any figure bearing a 5mm peg hole.
Option 2 is a modified version of the post, which can still be used by figures with 5mm peg holes, but also has a built-in clip which allows it to clip onto any 3mm diameter rail.
Option 3 is a two-stage post, which like Option 1, can fit into any 5mm peg hole, but also has a narrowed end allowing it to be used by figures with 4mm diameter peg holes.
Newly redesigned hands are able to hold or clip onto any 3mm diameter rod.
A new hinge design means this figure is now available to be printed in the Detail materials as well as WSF. However, WSF Polished is recommended for the best combination of durability and smoothness.
Supplied as a 14-piece kit. Finishing (painting/dyeing) required, alternatively can be purchased in one of the available pre-dyed colours.
Assembly instructions coming soon...
by
fakebusker83
Version 1.5
Edit: Added spare fingers. Just in case!
A variant of the hands done for the Masterpiece Seeker figure, but this version has its wrist joint replaced with a ridged peg. The wrist peg is 5mm in diameter and peg section is 7mm long.
Edit: Added spare fingers. Just in case!
A variant of the hands done for the Masterpiece Seeker figure, but this version has its wrist joint replaced with a ridged peg. The wrist peg is 5mm in diameter and peg section is 7mm long.
by
Drawn-SteelHero
Powerful hand-held acid blaster rifle converts into a 56mm robot action figure with 9 points of articulation.
Gun mode comes with a choice of three handles, any one of which can be fit onto the figure during assembly (and since they are attached via a simple clip-in hinge, you can keep the others handy and swap them later if you choose).
Option 1 is a standard 5mm post, which is compatible with any figure bearing a 5mm peg hole.
Options 2 and 3 are modified versions of the post, which can still be used by figures with 5mm peg holes, but also have built-in clips which allow them to clip onto any 3mm diameter rail. One version has the opening of the clip positioned parallel to the length of the gun, the other perpendicular.
Supplied as a 17-piece kit. Finishing (painting/dyeing) required, alternatively can be purchased in one of the available pre-dyed colours.
Assembly instructions coming soon...
Gun mode comes with a choice of three handles, any one of which can be fit onto the figure during assembly (and since they are attached via a simple clip-in hinge, you can keep the others handy and swap them later if you choose).
Option 1 is a standard 5mm post, which is compatible with any figure bearing a 5mm peg hole.
Options 2 and 3 are modified versions of the post, which can still be used by figures with 5mm peg holes, but also have built-in clips which allow them to clip onto any 3mm diameter rail. One version has the opening of the clip positioned parallel to the length of the gun, the other perpendicular.
Supplied as a 17-piece kit. Finishing (painting/dyeing) required, alternatively can be purchased in one of the available pre-dyed colours.
Assembly instructions coming soon...
by
Drawn-SteelHero
Hand-held electron rifle converts into a 56mm robot action figure with 9 points of articulation.
Gun mode comes with a choice of three handles, any of which can be glued in to the mounting point on the figure's back.
Option 1 is a standard 5mm post, which is compatible with any figure bearing a 5mm peg hole.
Option 2 is a modified version of the post, which can still be used by figures with 5mm peg holes, but also has a built-in clip which allows it to clip onto any 3mm diameter rail.
Option 3 is a two-stage post, which like Option 1, can fit into any 5mm peg hole, but also has a narrowed end allowing it to be used by figures with 4mm diameter peg holes.
Also has a series of tabs mounted on his back, which allow him to be used with certain figures as a vehicle-mounted weapon. Note that these do not in any way hamper his functionality with other figures.
Newly redesigned hands are able to hold or clip onto any 3mm diameter rod.
A new hinge design means this figure is now available to be printed in the Detail materials as well as WSF. However, WSF Polished is recommended for the best combination of durability and smoothness.
Supplied as a 14-piece kit. Finishing (painting/dyeing) required, alternatively can be purchased in one of the available pre-dyed colours.
Assembly instructions coming soon...
Gun mode comes with a choice of three handles, any of which can be glued in to the mounting point on the figure's back.
Option 1 is a standard 5mm post, which is compatible with any figure bearing a 5mm peg hole.
Option 2 is a modified version of the post, which can still be used by figures with 5mm peg holes, but also has a built-in clip which allows it to clip onto any 3mm diameter rail.
Option 3 is a two-stage post, which like Option 1, can fit into any 5mm peg hole, but also has a narrowed end allowing it to be used by figures with 4mm diameter peg holes.
Also has a series of tabs mounted on his back, which allow him to be used with certain figures as a vehicle-mounted weapon. Note that these do not in any way hamper his functionality with other figures.
Newly redesigned hands are able to hold or clip onto any 3mm diameter rod.
A new hinge design means this figure is now available to be printed in the Detail materials as well as WSF. However, WSF Polished is recommended for the best combination of durability and smoothness.
Supplied as a 14-piece kit. Finishing (painting/dyeing) required, alternatively can be purchased in one of the available pre-dyed colours.
Assembly instructions coming soon...
by
Cypherplex
Designed for the Generations Red Alert mold, this head modification will fit any 5mm standard ball joint neck.
Transform your spare Generations Red Alert into the Headmaster known as CHROMEDOME! The Chromehead upgrade is modeled based on the character's representation in the Takara's "The Headmasters" Transformers anime.
The recommended material is Polished White Strong and Flexible, though the figure is detailed enough to warrant a Frosted Ultra Detail production. I would only recommend that choice to customizers that will be able to finely detail the paint apps.
Be forewarned: Frosted Ultra Detail is extremely fragile on this model. Ball joints are known to break for no reason other than transforming back into robot mode. That's why I would recommend a more resistant material like WSF.
You might need to sand the three posts on the back of Chromehead's face. They are slightly longer by design to allow the head to pop off and on to the ball joint, but the excess in height leaves a visible crease (only if you look at it sideways... and you can easily position the arms of the figure to hide those anyway, I'm just writing it out here so that I don't get crappy feedback about shoddy design).
Sanding required to "tighten", though bear in mind that paint will also do the same.
Painting / dyeing required. Check out G2P-005b for the chest "Tech Spec Meter" and G2P-005c for G1 Toy Inspired guns!
by
fakebusker83
Version 1.5
Edit: Thickened front spikes for greater endurance and strength.
A vicious, spiky hand cannon to arm your alien robotic ground troops with! Made to be as accurate to the movie footage as possible, this design contains hoses, armour plates and other features that cannot be easily replicated with conventional molding techniques.
Printing in Strong Flexible is recommended due to the amount of fine, fragile details.
This model is tested in WSF.
Edit: Thickened front spikes for greater endurance and strength.
A vicious, spiky hand cannon to arm your alien robotic ground troops with! Made to be as accurate to the movie footage as possible, this design contains hoses, armour plates and other features that cannot be easily replicated with conventional molding techniques.
Printing in Strong Flexible is recommended due to the amount of fine, fragile details.
This model is tested in WSF.
by
VF5SS
Replacement part for Fighter Variable Zero. Complete set of shoulder and elbow parts. Requirements minor disassembly. For right side.
by
printedCat
This 5 cm nylon skeleton toy is an ideal gadget for Halloween or your keyboard's companion. Funny, tricky and cool
by
fakebusker83
Version 2.0
THIS VERSION IS UNTESTED. TEST PRICES AVAILABLE. ORDER AT YOUR OWN RISK.
This set contains all 3 individual head designs of the D.R.E.A.D series.
Version 1.0 has been tested in Frosted Ultra Detail and experienced some fit issues. Version 2.0 is fixed but untested. Frosted Ultra Detail is recommended.
THIS VERSION IS UNTESTED. TEST PRICES AVAILABLE. ORDER AT YOUR OWN RISK.
This set contains all 3 individual head designs of the D.R.E.A.D series.
Version 1.0 has been tested in Frosted Ultra Detail and experienced some fit issues. Version 2.0 is fixed but untested. Frosted Ultra Detail is recommended.
by
TecromDesigns
This is the latest version of the Oracle designs. The model when printed can be used with the Transformers Prime RID Arcee figure. The figures pictures was printed using the "Frosted Ultra Detail material." If the model is used with this toy, the head can remain attached during transformation. The model only includes the head as seen in the digital rotation.. Also pictured is an artists paint up of the figure with the head. The action figure is sold separately.
by
Goji62
The chief attack ship and interceptor of the Terran Navy, based on the older Sun Viper interceptor but with two extra wings and engines and a second turret for serious defense. Able to perform as both interceptor and bomber, the crews call them "XY" or androgynous ships. The wings look better on the miniature you will receive!
