by
virtox
Accused of being fake, witchcraft and simply impossible..
This kinetic sculpture is inspired by the unlimited freedom of 3d printing,
it wobbles and turns with a slight movement of the hand.
Now give it a good spin or puff of air and it erupts in erratic and wild behavior.
This is the 5cm / 2" version, see the Gyro the Forms section for other shapes and sizes.
Corner stand available separately, or get the complete set below!
NEW!
Now also available as a pendant/keyfob!
In both Extra small and Small
Instructions
It is composed of four concentric cubes, each one spinning around a different axis.
The model needs some minor assembly:
Each inner cube has two knobs which need to be placed into the corresponding clamps in the parent cube. It's easiest to start with the inner most and continue outward.
And then... spin it away !
Notes
Do not be alarmed if your cube will not run smoothly at first!
Because of minor variations as a result of the printing process,
some need to wear in a little but will loosen up very quickly.
In the example video I am blowing on it to make it move, it's that smooth.
Be a little careful with (the assembly of) the Alumide version as this material is slightly less flexible/robust than the Strong & Flexible materials.
Get a complete set.
A default set consists of an Alumide Gyro the Cube and a White stand, you can change the materials in your cart later.
+ 
This kinetic sculpture is inspired by the unlimited freedom of 3d printing,
it wobbles and turns with a slight movement of the hand.
Now give it a good spin or puff of air and it erupts in erratic and wild behavior.
This is the 5cm / 2" version, see the Gyro the Forms section for other shapes and sizes.
Corner stand available separately, or get the complete set below!
NEW!
Now also available as a pendant/keyfob!
In both Extra small and Small
Instructions
It is composed of four concentric cubes, each one spinning around a different axis.
The model needs some minor assembly:
Each inner cube has two knobs which need to be placed into the corresponding clamps in the parent cube. It's easiest to start with the inner most and continue outward.
And then... spin it away !
Notes
Do not be alarmed if your cube will not run smoothly at first!
Because of minor variations as a result of the printing process,
some need to wear in a little but will loosen up very quickly.
In the example video I am blowing on it to make it move, it's that smooth.
Be a little careful with (the assembly of) the Alumide version as this material is slightly less flexible/robust than the Strong & Flexible materials.
Get a complete set.
A default set consists of an Alumide Gyro the Cube and a White stand, you can change the materials in your cart later.
+ 
by
TerraCotta
If M.C. Escher had owned fidget toys, he would have worn "One ring to rule the ball" as a pendant. A single, continuous line contains a small ball that makes orbit after mesmerizing orbit but cannot escape, always held down in four directions. Available in solid, durable stainless steel with optional antique bronze and gold plated finishes to fit any context, "One ring to rule the ball" now also includes a free rubber necklace so that you can confuse your mind any time the fancy strikes you! One customer echoes many others in saying, "I couldn't put it down. This thing is just too fun!"
Purchases by those gracious customers have now paid for the design time on this piece so it is available on a pay-what-you-want basis. Ordering from this page contributes 5$ towards continuing work such as the new, even more impossible "One ring to pwn the ball" (just released October 18th!) which can be found at http://www.shapeways.com/model/145172/one_ring_to_pwn_the_ball.html and the open-source "Ultimate Desk Toy" at http://www.shapeways.com/model/109166/ultimate_desk_toy.html . To download the original 3d file for your own use under a CC-BY license ( http://creativecommons.org/licenses/by/2.5/ca ) click "Download" at top right . To learn more about this design or other work from Terra Cotta, visit our website at http://www.terracottapf.com
Purchases by those gracious customers have now paid for the design time on this piece so it is available on a pay-what-you-want basis. Ordering from this page contributes 5$ towards continuing work such as the new, even more impossible "One ring to pwn the ball" (just released October 18th!) which can be found at http://www.shapeways.com/model/145172/one_ring_to_pwn_the_ball.html and the open-source "Ultimate Desk Toy" at http://www.shapeways.com/model/109166/ultimate_desk_toy.html . To download the original 3d file for your own use under a CC-BY license ( http://creativecommons.org/licenses/by/2.5/ca ) click "Download" at top right . To learn more about this design or other work from Terra Cotta, visit our website at http://www.terracottapf.com
by
schreerdesign
(Note, prices reduced) This is a sound magnifier for your iPhone 4 or 4s (does not fit others), based on the old Gramophones of the late 19th and early 20th Centuries. NOTE: BASE AND HORN ARE NOW SOLD SEPARATELY FOR TECHNICAL REASON. THIS FILE IS THE BASE ONLY. SEE THIS LINK FOR THE HORN: http://shpws.me/5i0B . (Adding this to cart will add both)
+ 
Want to get a set?
+ 
by
Pazu
Working centrifugal compressor.
Designed to fit standard Mabuchi 130 motors.
Printed and tested.
Upon receiving the item, you'll need to use a 1.8mm drill bit to drill out the center hole. This is due to limitation of the printing process that may not allow the shaft of the motor to be inserted.
Designed to fit standard Mabuchi 130 motors.
Printed and tested.
Upon receiving the item, you'll need to use a 1.8mm drill bit to drill out the center hole. This is due to limitation of the printing process that may not allow the shaft of the motor to be inserted.
by
virtox
Phamora Ceramics!
Is inside out? Or is it not? Perhaps both?
This is an Amphora from another space-time.
An ancient object which we knew had to exist.
And after years of excavation in other dimensions we finally found it!
A very exotic vase with a unique near-impossible shape, suitable for use with dry flowers and striking enough to stand alone.
Theoretically it can also hold water in the toroidal bottom part, read practical details below.
Very suitable as a wedding gift to symbolize love and infinity.
The number eight (or sideways infinity) plays an important role in this piece,
both in the number of arms and the cross-section of this model.
Notes:
To improve print quality and after some deliberation with production, this model has been slightly updated on August 24th 2012; The arms have been thickened and the holes enlarged to improve strength and glazing.
Still I recommend not to put a lot of stress on the handles.
Refer to rendered images for the latest version. I will update photo's asap.
The bottom it stands on, is unglazed, which is invisible during normal display.
All clearly visible parts will be fully glazed, but there is a chance some parts on in the inside might not, which may compromise it's ability to hold water.
While production does their absolute best and all recent prints turned out perfectly glazed and hold water, due to the complexities involved, there is no 100% guarantee for to be absolutely watertight.
Is inside out? Or is it not? Perhaps both?
This is an Amphora from another space-time.
An ancient object which we knew had to exist.
And after years of excavation in other dimensions we finally found it!
A very exotic vase with a unique near-impossible shape, suitable for use with dry flowers and striking enough to stand alone.
Theoretically it can also hold water in the toroidal bottom part, read practical details below.
Very suitable as a wedding gift to symbolize love and infinity.
The number eight (or sideways infinity) plays an important role in this piece,
both in the number of arms and the cross-section of this model.
Notes:
To improve print quality and after some deliberation with production, this model has been slightly updated on August 24th 2012; The arms have been thickened and the holes enlarged to improve strength and glazing.
Still I recommend not to put a lot of stress on the handles.
Refer to rendered images for the latest version. I will update photo's asap.
The bottom it stands on, is unglazed, which is invisible during normal display.
All clearly visible parts will be fully glazed, but there is a chance some parts on in the inside might not, which may compromise it's ability to hold water.
While production does their absolute best and all recent prints turned out perfectly glazed and hold water, due to the complexities involved, there is no 100% guarantee for to be absolutely watertight.
by
TerraCotta
Even fidget toys get to have a "2.0" . An updated version of the popular "One ring to rule the ball" design with fewer twists, thicker wire, and a bigger ball, "One ring to pwn the ball" takes its steampunk ancestry in a smooth, contemporary direction that's twice as ruthless with your mind--it seems doubly impossible that this ball could be solidly contained by just one short, twisting wire. With no hole in the middle for a rubber or leather strap, you'll have to go to http://www.shapeways.com/model/145208/one_ring_to_pwn_the_ball_pendant.html to wear it around your neck. But in both cases you'll get solid stainless steel with optional bronze antiquing or gold plating, and a look that ties brains in knots.
For the classic "One ring to rule the ball" design, now available on a pay-what-you-want basis, go to http://www.shapeways.com/model/52936/one_ring_to_rule_the_ball.html . To learn more about this design or other work from Terra Cotta, visit our website at http://www.terracottapf.com
For the classic "One ring to rule the ball" design, now available on a pay-what-you-want basis, go to http://www.shapeways.com/model/52936/one_ring_to_rule_the_ball.html . To learn more about this design or other work from Terra Cotta, visit our website at http://www.terracottapf.com
by
vertigopolka
This is the original hand-crank fan. A slimmer (and less expensive) version can be seen here: Hand-Crank Fan - slim, and both models are still being tweaked a bit before they are released for sale.
This model is specifically designed for the loose tolerances of the WSF materials, and is a single print with six moving parts, although not really effective as a real fan. The entire model is printed with all of the parts in position; nothing is assembled post-production. The 1:9 gear ratio (made of two sets of gears each with a 1:3 gear ratio) makes the fan blades rotate nine times around for every single rotation of the crank. The grip of the handle rotates freely as well.
This model is specifically designed for the loose tolerances of the WSF materials, and is a single print with six moving parts, although not really effective as a real fan. The entire model is printed with all of the parts in position; nothing is assembled post-production. The 1:9 gear ratio (made of two sets of gears each with a 1:3 gear ratio) makes the fan blades rotate nine times around for every single rotation of the crank. The grip of the handle rotates freely as well.
by
ThreeDimensions
1:72 Scale Triceratops
Pictured model is printed in frosted detail, I sprayed it with a layer of grey model primer.
