by
virtox
Accused of being fake, witchcraft and simply impossible..
This kinetic sculpture is inspired by the unlimited freedom of 3d printing,
it wobbles and turns with a slight movement of the hand.
Now give it a good spin or puff of air and it erupts in erratic and wild behavior.
This is the 5cm / 2" version, see the Gyro the Forms section for other shapes and sizes.
Corner stand available separately, or get the complete set below!
NEW!
Now also available as a pendant/keyfob!
In both Extra small and Small
Instructions
It is composed of four concentric cubes, each one spinning around a different axis.
The model needs some minor assembly:
Each inner cube has two knobs which need to be placed into the corresponding clamps in the parent cube. It's easiest to start with the inner most and continue outward.
And then... spin it away !
Notes
Do not be alarmed if your cube will not run smoothly at first!
Because of minor variations as a result of the printing process,
some need to wear in a little but will loosen up very quickly.
In the example video I am blowing on it to make it move, it's that smooth.
Be a little careful with (the assembly of) the Alumide version as this material is slightly less flexible/robust than the Strong & Flexible materials.
Get a complete set.
A default set consists of an Alumide Gyro the Cube and a White stand, you can change the materials in your cart later.
+ 
This kinetic sculpture is inspired by the unlimited freedom of 3d printing,
it wobbles and turns with a slight movement of the hand.
Now give it a good spin or puff of air and it erupts in erratic and wild behavior.
This is the 5cm / 2" version, see the Gyro the Forms section for other shapes and sizes.
Corner stand available separately, or get the complete set below!
NEW!
Now also available as a pendant/keyfob!
In both Extra small and Small
Instructions
It is composed of four concentric cubes, each one spinning around a different axis.
The model needs some minor assembly:
Each inner cube has two knobs which need to be placed into the corresponding clamps in the parent cube. It's easiest to start with the inner most and continue outward.
And then... spin it away !
Notes
Do not be alarmed if your cube will not run smoothly at first!
Because of minor variations as a result of the printing process,
some need to wear in a little but will loosen up very quickly.
In the example video I am blowing on it to make it move, it's that smooth.
Be a little careful with (the assembly of) the Alumide version as this material is slightly less flexible/robust than the Strong & Flexible materials.
Get a complete set.
A default set consists of an Alumide Gyro the Cube and a White stand, you can change the materials in your cart later.
+ 
by
COVO
Product Name "Screwdriver Ring". Designed by Japan.
Available in either stainless steel (antique bronze & gold plated)
The default size is 20.6 mm inner diameter but you can customize the size to your liking.
Click personalize to choose your US ring size.(Size support: # 8 to # 13.)
Please refer to a this page.
Conversion chart for ring sizes
US Ring Size Inside diameter
8 18.1mm
9 19.0mm
10 19.8mm
11 20.6mm
12 21.4mm
13 22.2mm
Please also see other designs.
Shop here.
http://www.shapeways.com/shops/forma
FORMA Laboratory Facebook Page!
Available in either stainless steel (antique bronze & gold plated)
The default size is 20.6 mm inner diameter but you can customize the size to your liking.
Click personalize to choose your US ring size.(Size support: # 8 to # 13.)
Please refer to a this page.
Conversion chart for ring sizes
US Ring Size Inside diameter
8 18.1mm
9 19.0mm
10 19.8mm
11 20.6mm
12 21.4mm
13 22.2mm
Please also see other designs.
Shop here.
http://www.shapeways.com/shops/forma
FORMA Laboratory Facebook Page!
by
Whystler
Size 13 AMazeRing Tower
(nice metal version)
A tower pops out of the middle of a wonky fantasy maze! I have only marked this ring up $4.90 (the base cost was $20.10)
(nice metal version)
A tower pops out of the middle of a wonky fantasy maze! I have only marked this ring up $4.90 (the base cost was $20.10)
by
monitep
A ring for special event.
The best is to order it in Stainless Steel. You can customise the internal diameter from 13 to 22mm
The best is to order it in Stainless Steel. You can customise the internal diameter from 13 to 22mm
by
nervoussystem
Inspired by the complex forms of radiolarians, where intricate pattern is integral to structure, these shapes derive from a simulation of spring meshes. We created interactive software to morph, twist, and subdivide each design, transforming a simple mesh to a complex patterned structure.
size (inner circumference)
5 - 49.0mm
6 - 51.5mm
7 - 54.0mm
8 - 56.6mm
9 - 59.1mm
10 - 62.1mm
11 - 64.6mm
12 - 67.2mm
click CREATE to select your size
Watch a video showing the software we created to design these pieces http://vimeo.com/10074976
size (inner circumference)
5 - 49.0mm
6 - 51.5mm
7 - 54.0mm
8 - 56.6mm
9 - 59.1mm
10 - 62.1mm
11 - 64.6mm
12 - 67.2mm
click CREATE to select your size
Watch a video showing the software we created to design these pieces http://vimeo.com/10074976
by
kaptsan
Spiral ring with inside twisted braid looks great in silver and gold.
A personal description or logo can be added on the inside.
Contact me for more info.
by
seedlingdesign
A neo-classical homage to Plato and his solids or a geeky tribute to Buckminster Fuller? Whichever way you want to look at it, this mathematically inspired highbrow bling by Seedling is a sure talking point. The upper spherical structure is made up of 60 triangular faces which float elegantly upon the faceted ring.
